Question about 2003 Chrysler PT Cruiser

1 Answer

Location of crankshaft position sensor for 2003 pt cruiser

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Had this problem. The crankshaft position sensor (on 2003 non-turbo) is located directly under the starter. The Haynes and Chilton books will tell you the complete opposite. They state that it is located near the alternator. WRONG. Oh, it is really a pain to get to FYI.

Posted on May 25, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22246 Answers

SOURCE: There is no sensor on

around the bellhousing where it can access the flywheel is the most logical ,have you had a good look at the engine and looked at both front pulley and the bellhousing first though before asking?but some vehicles do have them in the block level with the craknshaft ,just have a good look and you will no doubt find it

Posted on Feb 19, 2011

blueextc3221
  • 15935 Answers

SOURCE: Crankshaft Position Sensor location 04 PT Cruiser

It is located behind the **** of the starter on the front of the engine starting in '03 the 2.4 lt was changes the repair manual failed to update this..you may sneak it out with small fingers with out pulling out the starter.

7e1821a.jpg

Posted on Feb 08, 2009

  • 27 Answers

SOURCE: were i the crankshaft position

near the oil filter.. above it...under exhaust manifold one small bolt holds it on. If the is a no start condition look for frayed wiring near crank sensor..... it has a harness that hangs too low on some of those. & rubs on cv shaft

Posted on Sep 15, 2010

  • 3 Answers

SOURCE: location crankshaft position sensor 2004

Its located on the engine block usually the front

Posted on Mar 24, 2011

emissionwiz
  • 76846 Answers

SOURCE: whats the position of the crankshaft position sensor on 2005 pt cruiser non turbo

P0344 CHRYSLER - Camshaft Position Sensor Intermittent Interruption Bank 1 Sensor 1
Possible causes - Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit

Posted on Dec 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whats the position of the crankshaft position sensor on 2005 pt cruiser non turbo


P0344 CHRYSLER - Camshaft Position Sensor Intermittent Interruption Bank 1 Sensor 1
Possible causes - Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit

Dec 14, 2011 | 2005 Chrysler PT Cruiser

2 Answers

Where is crank sensor on 2005 PT Cruiser? It absolutely is not above the oil filter as on 01-03 PT's.


REMOVAL - 2.0, 2.4, 2.4L TURBO
The Crankshaft Position Sensor is in the front of the engine block just under the starter motor (CRANKSHAFT POSITION SENSOR LOCATION).

Disconnect the negative battery cable.
Raise vehicle and support.
On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
Remove the Structural Collar (Structural Collar and Bending Strut-(Automatic Transaxle Equipped) ), refer to the Engine, Structural Collar Removal and Installation section.
Unlock and disconnect the electrical connector to the crankshaft position sensor.
Remove the crankshaft position sensor bolt.
Remove the sensor. Arrow points to sensor in picture.


emissionwiz_108.gif

Aug 22, 2011 | 2005 Chrysler PT Cruiser

1 Answer

Were i the crankshaft position sensor located o a 2005 pt cruiser


near the oil filter.. above it...under exhaust manifold one small bolt holds it on. If the is a no start condition look for frayed wiring near crank sensor..... it has a harness that hangs too low on some of those. & rubs on cv shaft

Sep 14, 2010 | 2005 Chrysler PT Cruiser

1 Answer

Need to know where the crank shat sensor s located on a 2003 pt crusier


Follow your plug wires to your coil packs. Your coil packs are attached to the ignition module. There will two wires running form ignition module right to the crankshaft position sensor which should be in the engine block

Aug 07, 2010 | 2003 Chrysler PT Cruiser

2 Answers

After changing the camshaft censor and the car still wont start what could be the problem also is there a fuse that needs to be replaced this is a 2004 pt cruiser the code say its the camshaft censor also...


P0016 crankshaft/camshaft timing misalignment
p0340 camshaft sensor

intermittent crankshaft sensor

PCM detects an error when the camshaft position is out of phase with the crankshaft position

Sep 26, 2009 | 2004 Chrysler PT Cruiser

1 Answer

Where can I find the crankshaft position sensor on a 2005 Pt Cruiser Non turbo gasoline


IT IS LOCATED IN THE BLOCK BELOW THE STARTER..UNPLUG CONNECTOR AND 1 BOLT..IT MAY BE STUCK IN BLOCK..SPRAY WITH PENETRATING OIL..MOVE BACK AND FORTH PULL OUT OF BLOCK

Jul 14, 2009 | 2004 Chrysler PT Cruiser

1 Answer

Replace crankshaft sensor


Crank sensor on that car should be located near the pulley end of the motor, and near the firewall side. Fairly easy to get to.

Mar 06, 2009 | 2003 Chrysler PT Cruiser

1 Answer

Crankshaft Position Sensor location 04 PT Cruiser


It is located behind the **** of the starter on the front of the engine starting in '03 the 2.4 lt was changes the repair manual failed to update this..you may sneak it out with small fingers with out pulling out the starter.

7e1821a.jpg

Feb 08, 2009 | 2004 Chrysler PT Cruiser

Not finding what you are looking for?
2003 Chrysler PT Cruiser Logo

2,170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...