Question about 2000 Dodge Stratus

1 Answer

I can't get the crankshaft damper pulley off of a 2000 Dodge Stratus, 2.4L, DOHC. My end goal is to remove the timing belt. I have already removed the accessory drive belts, but cannot remove the crankshaft damper pully. Before the pulley gets out far enough to remove it, the pulley bumps up against a body component.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Download this link and find your Service manual for your vehicle. It will serve you well and to keep for future reference

http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

Posted on May 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I set the timing on a 1996 dodge stratus 2.4l engine


  1. Using sprocket installation tool No. 6792 or equivalent, press the crankshaft sprocket onto the crankshaft.
  2. Install the camshaft sprockets onto the camshafts. Install and tighten the sprocket retaining bolts to 75 ft. lbs. (101 Nm).


0900c152800896f5.jpg
enlarge_icon.gifenlarge_tooltip.gif
Fig. Fig. 4: Proper camshaft sprocket alignment for timing belt installation

  1. Install the crankshaft sprocket. Set the crankshaft sprocket to Top Dead Center (TDC) by aligning the notch on the sprocket with the arrow on the oil pump housing.
  2. Set the camshafts to align the timing marks on the sprockets.
  3. Move the crankshaft to 1 / 2 notch before TDC.
  4. Install the timing belt starting at the crankshaft, then around the water pump sprocket, idler pulley, camshaft sprockets, and then around the tensioner pulley.
  5. Move the crankshaft sprocket to TDC to take up the belt slack.
  6. Install the tensioner to the engine block, but do not tighten.
  7. Using a torque wrench on the tensioner pulley apply 250 inch lbs. (28 Nm) of tighten to the tensioner pulley.
  8. With torque being applied to the tensioner pulley, move the tensioner up against the tensioner pulley bracket and tighten the fasteners to 275 inch lbs. (31 Nm).
  9. Remove the tensioner plunger pin. The tension is correct when the plunger pin can be removed and replaced easily.
  10. Rotate the crankshaft 2 revolutions and recheck the timing marks. Wait several minutes and then recheck that the plunger pin can easily be removed and installed.
  11. Reinstall the front timing belt cover(s).
  12. Reinstall the engine mount bracket.
  13. Reinstall the right engine mount.
  14. Remove the floor jack from under the vehicle.
  15. Install the crankshaft damper and tighten to 105 ft. lbs. (142 Nm).
  16. Install the accessory drive belts and adjust to the proper tension.
  17. Install the right inner splash shield.
  18. Reconnect the negative battery cable.
  19. Check for leaks and proper engine operation.

Source: Autozone.com

May 22, 2013 | 1996 Dodge Stratus

1 Answer

1999 ford taurus 3.0 dohc


this job does require some special tools to remove the crankshaft balancer....
Removal
1. Disconnect battery ground cable.
2. Remove drive belt.
3. Raise vehicle on hoist.
4. Remove RH front wheel and tire assembly.
5. Remove four crankshaft pulley to damper retaining bolts and remove crankshaft pulley.

printer.png Zoom and Print Options42_fm99tausa_303.01a-027b.png&width=448&height=330&displaytype=display&imgrotation=&links=

6. Remove crankshaft damper retaining bolt and washer.

7. CAUTION: Use care when removing damper so as not to damage crankshaft or create burrs.

Remove damper from crankshaft using Crankshaft Damper Remover 303-009 (T58P-6316-D) and Vibration Damper Remover Adapter 303-176 (T82L-6316-B).

Jun 15, 2012 | 1999 Ford Taurus

1 Answer

Im trying to find crank sensor for 2000 dodge stratus 2.4,where is it located on motor


Make the FixYa experience better for everyone by voting.

Hi,

My name is Ben and I'm your guru, i.e., mentor, an influential teacher or popular expert: a management guru. - origin from Sanskrit, 'weighty, grave' for today.


Query: I'm trying to find crank sensor for 2000 dodge stratus 2.4,where is it located on motor

Response: On the passenger side of the engine. You'll have to go under the car and look for the harmonic balancer -- located on the end of the crankshaft and you should see it.It has 1 screw and it is on the engine under the passenger side under the tire by the bottom pulley.

All the best,

Ben

Sep 12, 2011 | 2000 Dodge Stratus

1 Answer

How do i use a 10 inch three jaw adjustable puller to remove a crankshaft damper on a 1997 2.4 liter D.O.H.C dodge stratus?


You don't. There is a special 3 jaw puller, specific for Chrysler products and a few other vehicles. I comes with three various length rods that slide into the hole in the end of the crankshaft and into the end of the puller bolt to obtain the correct length. The jaws of the puller have slots rather than hooks that slide onto machined surfaces in the inner part of the damper. These pullers are available for rent at auto parts stores. usually it's free, you just leave a deposit. trying to use a standard puller on the outside of the damper will damage the damper.

Aug 17, 2011 | Dodge Stratus Cars & Trucks

1 Answer

WHAT IS CORRECT TIMING MARKS FOR TIMING BELT INSTALLATION. 2000 NUBIRA 2.0 DOHC AND CRNKSHAFT MARKS. Thanks Joe


TIMING BELT
Removal
Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing.
Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt.
Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle.
Support engine assembly from above with Support Fixture (J-28467-B). Remove engine mount bracket from timing belt end of engine.Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine).
Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 .
CAUTION: Engine damage could result if camshaft sprockets are not properly aligned with notches on valve cover.
Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. Remove timing belt.
Fig. 4: Aligning Crankshaft Sprocket Timing Mark
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim_4.jpg
Fig. 5: Aligning Camshaft Sprocket Timing Marks
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim2_3.jpg
Installation
Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS .
Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch.
If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt.
Install right front splash shield. Install right front wheel. Install air filter housing and resonator. Connect air intake temperature sensor connector. Connect negative battery cable.
Fig. 7: Identifying Timing Belt Routing
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim3_1.jpg
here

http://www.2carpros.com/questions/daewoo-leganza-2000-daewoo-leganza-timing-marks

Feb 17, 2011 | 2000 Daewoo Nubira

1 Answer

I have a 2002 dodge stratus with a 2.4l 4cyl dohc change oil pump


The oil pump is built in the front cover of the crankshaft,it is a kit that installs,to make the pump,check the oil pump screen first,they get stopped up on these,so it could just be that.

Jun 06, 2010 | 2002 Dodge Stratus

1 Answer

I am having troubles locating the cam shaft timing marks on my 1999 VW passat VR6 engine. any ideas


hi, here is a guide i have come across on this site written by another expert it should be the one for your engine but always double check.

If you are unsure what you are doing then please go out and buy a haines workshop manual as these tell you every detail you need to know so that would be your best solution.

Please dont do this work if your unsure what you are doing as you could damage the engine beyond repair so you have been warned;

it covers single cam and if you scroll down it shows double cam ok

Sep 14, 2009 - VW Passat & Audi A4 1990-2000 Repair Guide
Timing Belt - REMOVAL & INSTALLATION

2.8L SOHC (AFC) V6 Engine
  1. Note the radio security code and disconnect the negative battery cable.
  2. Place the (hood) lock carrier in the service position. For additional information, please refer to the following topic(s): Body And Trim, Service Position, Front Bumper, Hood Lock Carrier.
  3. Remove the engine accessory drive belt. For additional information, please refer to the following topic(s): General Information And Maintenance, Routing Maintenance And Tune-up.
  4. Turn the engine by hand to Top Dead Center (TDC) on the firing stroke for cylinder No. 1.
NOTE The large holes in the camshaft sprocket lock plates should be on the inside facing one another.
  1. Remove the Crankshaft Position (CKP) sensor from the lower left side of the engine block. Make sure the engine is at TDC and install the threaded crankshaft holding pin Tool No. 3242 and lightly tighten.
  2. Remove the upper timing belt covers, the crankshaft vibration damper and then the lower timing belt cover.
  3. Loosen the camshaft sprocket bolts slightly and use a suitable pulley to release the sprockets from the tapered ends of the camshafts.
  4. Loosen the tensioner roller and remove the drive belt.
To install :
  1. Install the timing belt over the sprockets, then the idler rollers and lastly over the tensioner.
  2. Install camshaft alignment tool holder Tool No. 3243 into the camshaft alignment flanges.
  3. Check and adjust the cam belt tension such that the upper left portion of the belt between the tensioner and the left cam gear can just be twisted 90° ( 1 / 4 turn).
  4. Tighten the cam belt tensioning roller to 33 ft. lbs. (45 Nm), and the camshaft sprocket bolts.
  5. The balance of the installation is in reverse order of removal.

2.8L DOHC 5V (AHA) V6 Engine
  1. Note the radio security code and disconnect the negative battery cable.
  2. Place the (hood) lock carrier in the service position. For additional information, please refer to the following topic(s): Body And Trim, Service Position, Front Bumper, Hood Lock Carrier.
  3. Remove the engine accessory drive belt. For additional information, please refer to the following topic(s): General Information And Maintenance, Routing Maintenance And Tune-up.
  4. Turn the engine by hand to Top Dead Center (TDC) on the firing stroke for cylinder No. 1.
NOTE The large holes in the camshaft sprocket lock plates should be on the inside facing one another.
  1. On the cylinder block near the crankshaft, remove the sealing plug from the lower left side of the engine block. Make sure the engine is at TDC and install the threaded crankshaft holding pin Tool No. 3242 and lightly tighten.
  2. Remove the upper timing belt covers, the crankshaft vibration damper and then the lower timing belt cover.
  3. Loosen the camshaft sprocket bolts slightly and use a suitable pulley to release the sprockets from the tapered ends of the camshafts.
  4. Using a 8mm Allen® wrench, rotate the timing belt tensioner roller clockwise until the tensioner is compressed; then, insert a 2mm spring pin through the tensioner housing and tensioner plunger to secure it in place. When the plunger is secure, release the wrench tension.
  5. Remove the damper-to-crankshaft bolts and the damper.
NOTE It is not necessary to remove the center bolt when removing the crankshaft damper.
  1. Remove the serpentine belt idler and the crankshaft damper guard.
  2. Mark the running direction of the timing belt and remove it from the pulleys.
58637f8.jpg

Fig. Crankshaft pulley alignment location for TDC-Audi 2.8L V6 engines


d58d8c0.jpg

Fig. Left camshaft sprocket alignment position for TDC; right camshaft position is similar-Audi 2.8L V6 engines


934cbaf.jpg

Fig. View of crankshaft holding tool installed-Audi 2.8L V6 engines


9091ff0.jpg

Fig. View of camshaft locator bar installed-Audi 2.8L V6 engines


To install:
  1. Make sure that the camshaft pulleys and the crankshaft pulley are in alignment with TDC of the No. 1 cylinder's compression stroke.
  2. Install the timing belt; make sure the timing belt is installed in the correct running direction from which it was removed.
  3. Using a 8mm Allen® wrench, rotate the timing belt tensioner roller clockwise until the tensioner is compressed; then, remove the 2mm spring pin from the tensioner housing. Slowly, release the tensioner spring pressure to put pressure on the timing belt.
  4. Install the crankshaft damper guard and the serpentine belt idler pulley; torque the idler pulley bolts to 33 ft. lbs. (45 Nm).
  5. Install the crankshaft damper and torque the damper-to-crankshaft bolts to 15 ft. lbs. If the damper-to-crankshaft center bolt was removed, torque it to 147 ft. lbs. (200 Nm) plus 180° 1 / 2 turn).
  6. Remove the Crankshaft Holder tool No. 3242 and install the sealing plug.
  7. Replace the remaining components by reversing the removal procedures.
  8. Refill the cooling system and the automatic transaxle. Connect the electrical connectors. Install the negative battery cable last.
  9. Test drive the vehicle.

Jan 18, 2010 | Volkswagen Passat Cars & Trucks

1 Answer

Where is the crankshaft sensor on a 05 dodge stratus


I need more info..Like what size motor,,this car came with 4 different moros..2.4 sohc 2.4 dohc 2.7 dohc. and a 3.0 sohc...once i get that i can help you out, because they are in different areas, and they look different

Dec 24, 2009 | 2005 Dodge Stratus

Not finding what you are looking for?
2000 Dodge Stratus Logo

1,047 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...