Question about 1996 Nissan 200SX

2 Answers

1996 200sx brake pedal goes to floor. no brakes

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

Sounds like you might have a bad master cylinder or a brake fluid leak, such as a rusted out brake line.

Posted on May 02, 2010

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer got voted for 20 times.

  • Contributor
  • 361 Answers

You have lost your fluid. in other words you have a leak, probably from a caliper on the wheel. look behind your wheels and see if there is any fluid on the tire or floor. Top up the reserverve and pump the brakes with the engine running see if this brings some of the pedal back. then get it to a brake shop and get it fixed.

Posted on May 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The brake pedal goes right to the floor


Did you try bleeding the brakes? Sounds like air in the line.

Dec 22, 2012 | 2002 Ford Explorer

3 Answers

Are there vacuum hose on the brakes hydraulic system?


NO. the vacuum is used to make the brake pedal easy to push, power brakes. the pedal would be hard without vacuum, that is why the pedal gets hard with the key off and engine not running. the problem you are having is more of a hydraulic problem.
Have the brakes checked asap. the brake system may have a leak causing the pedal to go low. check the fluid level and if it is low or empty then there is a problem, could be a rotted brake line leaking or a wheel cylinder leaking.

Dec 07, 2012 | 1997 Ford Probe

1 Answer

What are the proper steps to bleeding your brakes on a 1990 vw golf deisel


For left hand drive vehicles: (If the car does not have ABS system you do not need any diagnostic equipment!)

IMPORTANT NOTE: You need using diagnostic equipment connected to the data link connector of the car in order to bleed the ABS block. Follow instructions by scantool equipment for bleeding the ABS block.


1. This bleeding procedure requires two people. Remove the brake system reservoir cap, and fill up with new brake fluid until "MAX" level is reached.
2. Lift the car, or use a channel for access under vehicle.
3. Put the gearbox in "N" - Neutral position, or in "P" - Parking position for automatic transmission.
4. Start the engine and push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor.
5. Begin with the rear right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
6. Repeat steps no.#4 and no.#5 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

7. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
8. Continue with the rear left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
9. Repeat steps no.#7 and no.#8 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

10. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
11. Continue with the front right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
12. Repeat steps no.#10 and no.#11 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

13. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
14. Continue with the front left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
15. Repeat steps no.#13 and no.#14 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.
16. Now the brakes are bleeded. Check the brake fluid level in the reservoir. Fill up with new brake fluid until "MAX" level is reached. Put back the brake reservoir cap.
17. Test the car brake system. The brake pedal movement no more than 1/3 of total stroke until the floor, when brake pedal is applied. Maximum admissible is 1/2 of total stroke.

Dec 06, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

Bleeding front brakes and brake pedal still goes to floor board


Must bleed all four brakes to determine if there is air in the lines.

If after bleeding several times, the brake pedal still goes to the floor board, the master cylinder may be determined to be bad.

Aug 12, 2010 | 2002 Buick LeSabre

1 Answer

Brake pedal goes to floor on first depression; then pumps up fine


Try this,apply the emergency before stepping on the brake.
If this helps the pedal,the rear brakes are out of adjustment.

Jul 01, 2010 | 2000 Saturn L-Series

1 Answer

Brake pedal goes to the floor


check vacumn and\or connections to the vacumn boost cannister.

Apr 21, 2010 | 1985 Ford F150

2 Answers

With motor running, brake pedal goes to floor and swoosh of air is heard


Could be brake booster leaking. When engine is off the brake pedal should be firm and not go to the floor. If the pedal goes to the floor engine off, there may be a master cylinder problem also.

Oct 28, 2009 | 2005 GMC Envoy Xl

1 Answer

Brakes spongy after shop replaced rotors braked pads on 2001 buic


Sounds like air is still in the brake lines, the air sound that you hear is the power assist, but the brake pedal needs to be "high and hard".

if the pedal goes to the floor, that is not good. Sometimes, when pumping brakes for bleeding purposes, the master cylinder gets damaged, as the piston goes past it's normal "travel zone" and gets damged on deposits.....

Now, with that being said, if everything was perfect, brakes are typically not as firm after replacement, due to differences in new pads/shoes and old rotors and drums. Pedal to the floor, however, is never okay.

Doc

Sep 18, 2009 | 1995 Chevrolet Blazer

1 Answer

Brake pedal will go all the way to the floor


make sure brake fluid is full. then pump brakes for one minuite check the fluid to see if it went down or stayed full. if it went down then check the system for a leak . if it stays full then you will need a new mastercylender . i dont think you have a vacum problem cause this causes a verry stiff brake pedal not one that goes to the floor

Dec 26, 2008 | 1993 Ford Crown Victoria

2 Answers

97 ford e350 brake pedal goes to the floor...


are your rear drums set up? why did you bleed the brakes. when only when you installed new pads?

Sep 11, 2008 | 2002 Ford E350

Not finding what you are looking for?
1996 Nissan 200SX Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...