Question about 2000 Nissan Xterra

1 Answer

2000 nissan xterra abs light - 2000 Nissan Xterra

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 462 Answers

Any lights for control systems cannot be diagnosed without scaning the memory of car computers ,
mechanic shops only , unless you have this equipment.

Posted on May 02, 2010

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Torque and sequence to Intake Manifold for 3.3L Nissan Xterra 2000

Hi El Faraon,
I believe that you're dealing with 12 mm bolts and nuts....THESE ARE NOT THE SPECS FOR YOUR ENGINE, but I believe that if you use them you'll be close....Tighten in three stages up to 22nm....choose the bolts from the centre of the manifold and circle outwards until you reach the last one.....It may be a good idea to draw an overhead or plan view of the unit, marking out the bolt positions.....Start at the centre and mark the sequence and follow that....What is important is starting at the centre, so that nothing becomes warped....

Hope this helps,

Regards, Johngee10

Posted on Sep 06, 2008

TwinTurboZ
  • 78 Answers

SOURCE: 2000 Nissan Xterra Service Engine soon indicator is always on

The knock sensor is not a huge deal to replace and will not turn on the light. It should be dont though.

The crankshaft sensor is located directly between the engine and transmission. It is dead center at the bottom.

Posted on May 21, 2009

  • 1 Answer

SOURCE: 000 NISSAN Xterra -- after warming up, loses RPM by 500-1000..... have replaced ignition wires and distributor, checked mass air flow sensor and OK.....

I had a problem on my Nissan Xterra 2000. Symptons sound similar. In my case, it ran fine for a while and then suddenly the engine starts to stumble and lose output. At one point it did not even have enough HP to move. Irregular idling too. Thought it was water in my fuel. Bought water remover from the store and added to gas tank. Problem did not go away. Instead, "Service Engine Soon" light came on. Had to have it towed to the dealer as there was no way the engine could keep up with traffic. Dealer replaced the "Crank Position Sensor" today. Parts $33.00, Labor: $300 (about 3 hrs worth of work). Seems to work fine now but I will wait and see. Dealer also stated that Distributor bearing appears to be noisy and will need to be replaced sooner or later. I will wait for it to go before I fix that.

Posted on May 27, 2009

  • 16 Answers

SOURCE: parking lights nissan 2002 xterra

Open the back lift door. Inside next to the lights there are screws that need to be removed before you can get the whole parking light off. After you get the screws out, you will have to force the whole plastic light cover to get to the burn out light. Once you get the whole light out, replace the bulb and follow the process in reverse.

Posted on Jul 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Abs light turns on


What codes came up ?

Need a repair shop to resolve the abs system,
unless you have factory manuals

Oct 25, 2012 | 2000 Nissan Xterra

1 Answer

My 2000 Nissan xterra while driving the ABS light came on then the air bag and seatbelt lights started blinking and then the radio lights blinked a couple times and then completely went blank. Any...


absolutely no idea offhand to be honest i would suspect a earth connection behind the dash somewhere as my first suspicion ,but it may pay to ask a local dealer as a dealer fitter who only works on one make of vehicle would undoubtly have more experiance of their own make of vehicle than a general mechanic like myself who will attempt anything on any vehicle but doesnt know the itty ***** gritty of that or this particular model ---but i would sort it in the end that i can say

May 02, 2011 | 2000 Nissan Xterra

1 Answer

I have a 2000 Nissan Xterra, when I first got it the ABS light came on and I had the whole module replaced (2004) approximately a year ago it came back on. I understand that a sensor is probably bad but I...


I would suggest finding out what code there is causing the light to come on. Some parts stores or repair shops can retreive the code which should tell you where and what to check.

Oct 18, 2010 | 2000 Nissan Xterra

Not finding what you are looking for?
2000 Nissan Xterra Logo

Related Topics:

790 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...