Question about 1996 Chevrolet Monte Carlo

1 Answer

What are the torque spec's for the exhaust

What are the torque spec's for the exhaust manifold on a 1996 Monte Carlo with a 3.1 engine.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 76 Answers

To torque nuts and bolts start in the center using a criss cross pattern working outward.. final torque is 12 ftlbs.

Posted on May 02, 2010

Testimonial: "Thank You!"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm installing a 2.2 in a 2003 Oldsmobile Alero and I'd like to know the torque specs on the Exhaust bolts and studs. Thanks


Exhaust Manifold To Cylinder Head - 9.58 ft lbs
Exhaust Pipe To Exhaust Manifold - 20 ft lbs
you can check it out here, also all other torque specs for your engine.
Torque Specs Database

Feb 23, 2015 | 2003 Oldsmobile Alero

1 Answer

How do iremove oil pan 01 montecarlo


OIL PAN
Removal & Installation
1. Disconnect negative battery cable. Remove engine torque strut. Raise and support vehicle. Drain
crankcase. Disconnect oil level sensor electrical connector. Remove oil level sensor and oil filter.
Disconnect front exhaust pipe from manifold. Remove right front wheel and splash shield.
2. Disconnect oil cooler pipes. Disconnect A/C compressor electrical connector. Remove A/C compressor,
and position aside. Disconnect engine mounts from frame.
3. Remove flexplate access cover. Use transmission jack at transaxle to raise engine. Remove oil pan bolts
and oil pan. To install, reverse removal procedure. Install oil level sensor after oil pan is installed. Tighten
retaining bolts to specification. See TORQUE SPECIFICATIONS.

Sep 25, 2014 | 2001 Chevrolet Monte Carlo

1 Answer

Where is 02sensor monte carlo


inthe exhaust pipe just below the manifold 4cylinder has one to two v6 0r v8 has two to three all are in the exhaust one is usually behind the cataly tic converter the ohters will be up closer to the engine

Mar 03, 2013 | 2000 Chevrolet Monte Carlo

1 Answer

Need torque spec for a 1998 3.1 litre chevy v6


Hi there:
Are you refer at engine torque specf? Please confirm us.

Aug 10, 2012 | 1998 Chevrolet Malibu

2 Answers

2004 ford escape exhaust manifold torque specs?


2b507d0.jpg

Fig. Left side exhaust manifold bolt torque sequence-3.0L engine


22ac5ae.jpg

Fig. Right side exhaust manifold bolt torque sequence-3.0L engine

Both cases, exhaust manifold and new gasket, torque the bolts to 15 ft. lbs. (20 Nm).

Good luck (remember to rate this answer).

Oct 22, 2010 | 2004 Ford Escape

1 Answer

White smoke from exhaust in 1996 monte carlo


Head gasket failure or a crack in the cylinder head allowing engine coolant to enter the combudtion chamber, then out of the exhaust.

Jul 23, 2010 | 1996 Chevrolet Monte Carlo

1 Answer

2003 Chevy monte carlo 3.4L, need the torque


Check Autozone.com. There repair section should have the torque specs and order of tightening.

Mar 06, 2010 | 2003 Chevrolet Monte Carlo

1 Answer

2004 monte carlo, engine light on and engine stumbles and a backfiring/popping noise from upper intake manifold.


Not Good! Probably upper engine damage Intake or exhaust valve, possibly camshaft,Check the spark plug or wire condition.

Sep 10, 2009 | 2004 Chevrolet Monte Carlo

1 Answer

Need to know if long push rod goes into the exhaust valve


Long push rods are for exhaust valves. Short are intake.

Apr 24, 2009 | 1996 Chevrolet Monte Carlo

Not finding what you are looking for?
1996 Chevrolet Monte Carlo Logo

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...