Question about 1998 Chevrolet Blazer

1 Answer

I can't figure out how to replace the license plate lights.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Did you find a solution to this problem? ****@vt.edu

Posted on Jun 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to replace fuse for license plate bulbs for 2010 Ford Edge SEL....What fuse number is it?


normally the number plate light is on the same fuse as the park lights . I would be looking for a fault in the number plate area ( broken wire or blown bulb or bad/ no earth)

Dec 06, 2013 | Nissan Quest Cars & Trucks

1 Answer

2001 LeSabre - replace rear license light. The rear license plate lights do not light up the license at night. How do you get to them? What size bulb do you need?


kind of tricky, took me an hour to get it figured out, but you got to open the trunk and take out the 10 or so 10mm nuts sticking out of the backside of the lid, then the whole solid piece where the lights are on the back will slide off, then you can change the bulbs above the license plate and put it all back together, im cant remember off hand the bulb size, but your local auto parts store will have that info when you go to buy them

Mar 05, 2010 | 2001 Buick LeSabre

1 Answer

License plate bulb 99 alero


remove the 2 license lamp screws from outside,above the lic.plate then from insidethe trunk pull up the lic.lamp housing and replace the bulb.it should pull straight out

Apr 21, 2009 | Oldsmobile Alero Cars & Trucks

2 Answers

License plate lights do not work.


Sounds like you may have a wiring issue. I would cut the wires at the tag lamps, leaving enough to splice in new ones. Then pull one of your tail light assemblies out and, using a test light which is available from most parts stores for $5-10, figure out which wire is hot with the parking lights on. Splice a wire from there to your tag lamp socket. Then splice the other wire to the ground circuit at the tail lamp or find a good ground to wrap it around somewhere else (usually just about anything metal). Just find a bolt somewhere, back it out a bit and stick some of the stripped wire behind it at tighten it back up.

Apr 14, 2009 | Nissan Quest Cars & Trucks

1 Answer

How to change the license plate light on 2001 ford focus zx3


Take a thin blade screw driver and gently pry between the rubber seal and the metal and pop the light out, replaced the bulb and pop the light back in. works fine.

Mar 22, 2009 | 2001 Ford Focus

2 Answers

Bulb burnt out on license plate


you need the remove the lighting fixture first to access the bulbs.

Mar 19, 2009 | 2002 Cadillac Deville

2 Answers

License plate bulb on 1997 Cadillac deville


this is straight out of the book ok



  1. Open the rear compartment lid.
  2. Remove the rear compartment lid trim.
  3. Pull back on the rear compartment trim panel.
  4. Unplug the lamp connector from the rear compartment lid wiring harness.
  5. Press the grommet out of the rear compartment lid.
  6. Remove the nuts retaining the lamp assembly to the rear compartment lid.
  7. Remove the bulb.

Mar 07, 2009 | 1997 Cadillac DeVille

1 Answer

My license plate light is out on my 2002 Volkswagon Bug


Hi, press clip from inside and licance plate light assambly come out to you.

Mar 05, 2009 | 2001 Volkswagen Beetle

3 Answers

Licence light replacement 1996 Cadillac Deville


remove your license and behind it you will find i think two screws then remove that panel and you should be able to get to it.

Jan 22, 2009 | 1996 Cadillac DeVille

2 Answers

License Plate Lights


Probably not... For some reason license plate light wiring and sockets are VERY prone to corrosion. Make sure to check the light sockets and try to get to the wiring close to them, your problem is more than likely very close to the lights.

Aug 12, 2008 | 2005 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...