Question about 2002 Ford Taurus

1 Answer

No heat and fan only works on high

No heat

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,841 Answers

The fan only working on high is due to a defective blower motor resistor pack which must be replaced. No heat can be a clogged heater core, defective heater control valve, or thermostat stuck open. On a 8 year old car it is time for a full cooling system service. Drain, flush, replace the thermostat, and refill with a 50/50 mix of antifreeze and distilled water.

Posted on May 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 2009 Nissan Quest I can't turn the heat off. Just stays on a high level of blowing out heat .


If you have a fan that has different speed settings (1234, or low med high etc) and the only one that works is high - then the blower resistor pack has failed. If you have a climate control unit (where you just pick a temp you want) then the fan is controlled by the heating system and it sets fan speed. If you have climate control style try lowering the temp to a lower setting (current temp in vehicle) and see if fan slows down. If not then climate control unit or fan resistor bad. If dial type and you get nothing on lower settings (only high works like mentioned above) you need to change blower resistor. It is located under dash near the fan itself. Look for small unit bolted in duct near fan with wire plug going to it.

Feb 23, 2015 | Nissan Cars & Trucks

1 Answer

Does The Fan Come on When Turned on or Does it have to Heat Up First. Model JS-1500


As long as the fan _does_ come on, it is probably (highly likely) working correctly. These fans control ''overheating'' conditions. They aren't really for ''constant cooling'' like older cars.

Jan 01, 2015 | Cars & Trucks

2 Answers

Why does heat-air fan only work on high


Can you tell that the fan is getting higher or lower? Or is there no response from the fan control until you get to the high position?

Jun 24, 2014 | 2001 Chrysler Town & Country

1 Answer

Heating fan switch not working


cab heater? there are 3 fans, engine,cab heat and A/C. so....
a stuck CAB switch is a bad switch. easy huh?
if the switch only works on high but does move, that is a bad heater fan Resistor block. (usually bolted to fan hosing as it is air cooled this part)

Feb 01, 2014 | 1991 Toyota Pickup

1 Answer

Heating fan only works on high


there is a resistor next to the fan that is more than likely the problem should be an easy fix

Jan 09, 2013 | Cars & Trucks

1 Answer

The heat only works when its on high..when the fan is on.. when its on low or med there no heat blowing??


You have a bad resistor on the fan. High is the only speed that doesn't run through the resistor.

I hope this helps you.

Feb 02, 2011 | Chrysler Sebring Cars & Trucks

1 Answer

The only speed on my heat/air fan the will work is high. All other speed quite at the same time. Would this be the fan motor or could it be a fuse?


It is most likely the fan switch, all the low speed work through a resistance, the full speed does not, there is only one fuse for the fan so if it works on high its ok and you say the fan works on high so the fan itself is ok

Apr 17, 2010 | 2005 Ford Taurus

1 Answer

Heater & cooling fan only works on high.Power locks don't work.


there is a resistor for the heating and cooling fan speed. this controls the amount of voltage to your fan, which controls the speed. usually when the fan only works on high it will bypass the resistor and use the full 12 volts for the high setting. your power locks might be part of this circuit. i would check the resistor first then check the locks. usually the resistor is behind the high low switch

Mar 26, 2010 | 2000 Pontiac Montana

Not finding what you are looking for?
2002 Ford Taurus Logo

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...