Question about 2007 Ford Edge SEL Plus

1 Answer

Broken bolt pattern on motor/mount.

Is there an alternate motor mount for a 2001 ford ranger edge ?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 75,822 Answers

No just the one.

Posted on May 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i disconeect the motor mounts i need to disconnect motor mounts so i can raise the motor and remove th oil pan


The motor mounts have a hinge bolt that goes through the upper engine hard bracket and the engine mount rubber section, it goes from from to rear in line with the engine, remove the nuts and take the load off the mount with a floor jack under the pan (use a block softwood to avoid denting the pan), once the nut and load is off slide the long bolt out and raise the engine.

Jul 02, 2012 | 1999 Ford Ranger SuperCab

1 Answer

Where is the starter relay on 01 ford ranger 4.0


Check this procedure for 2.5L, 3.0L & 4.0L Engines
  1. Disconnect the battery ground cable.
  2. Raise and support the vehicle.
  3. Remove the starter cable retainer nut and release the retainer from the stud.
  4. Remove the bolts and lower the starter motor.
  5. Remove the cap.
  6. Remove the terminal nuts and remove the starter motor.
  7. To install, reverse the removal procedure. Torque all mounting bolts to 18 ft. lbs. (25 Nm).

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 12, 2011 | 2001 Ford Ranger Regular Cab

1 Answer

Im replaceing my alternator on my 2.3 liter 2001 ford ranger and I have the two bolds removed faceing the front of the truck on the mounting braquet but Im having trouble finding the third where can it be...


one bolt is to draw the tension that goes through the bracket with the adjustable cut out.Then there is one below it on the pivot point, on the complete opposite side of the pivot point there may be another bolt.If the pivot bolt is a long bolt approx 3-4 inches then there is only the two and all you have to do is work the alternator back and forth, a little force may be required.Sometimes the alternator gets a little stuck between it and the bracket.Please let me know if this helps

Jan 19, 2011 | Ford Ranger Cars & Trucks

1 Answer

Need to fix a camshaft position sensor on an 01 ford ranger 3.0


the cam sensor is located in the topside of the engine, behind the manifold, near the firewall. it is held in by two mounting bolts. just remove the wire connector and the two mounting bolts. you can then remove the cam sensor. slightly lube the oring on the new cam sensor and reinstall. tighten two mounting bolts and reconnect the wire connector

Mar 25, 2010 | 2001 Ford Ranger Regular Cab

1 Answer

Tire bolt size


I believe that is a 5x4.5 in pattern. To be sure take a tape measure and measure from the edge of one lug to the center of one of the opposite lugs. the bolt pattern is then in the format of (number of lugs x measurement between them) so in your case it will be a 5x(measurement)

Oct 27, 2009 | 2001 Ford Taurus

3 Answers

4x4 does not respond at all on 2001 ford Ranger Edge


I have a 2001 Ford ranger edge 4x4 with the 4.0L SOHC. My 4x4 module had to be replaced before I bought the truck used. The previous owner said the module was located behind the plastic panel that is under and to the right of the glove box. Mine makes a clicking noise whenever I turn the switch to 4x4 or 4x2. That's just the solenoid switch that is inside the module working. From what I've heard it's pretty common for the modules to get corroded from moisture over time in that location. Hope this helps. God bless

Sep 17, 2009 | 2000 Ford Ranger SuperCab

1 Answer

How do i install motor mounts on a 1995 ford ranger splash?


last i new it was two parts you will have to support the block and tran and remove the broken and replace

Jan 21, 2009 | 2004 Ford Ranger

2 Answers

Starter?


check the connections on your startermotor are all ok... mainly earthing... try using your jumpers to ground the engine to your battery... and hey try push starting... dont need a starter motor that way and lets you know if the engine is ok

Oct 28, 2008 | 2001 Ford Ranger Regular Cab

1 Answer

Wheel bolt pattern


According to everything I can find, yes.
It's a 5x114.3 bolt pattern (or 5x4.50)
However, your offset (from where the wheels bolt on to the edge of the rim) might be a little different depending on the wheel.

Sep 01, 2008 | 1993 Ford Ranger SuperCab

Not finding what you are looking for?
2007 Ford Edge SEL Plus Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...