Question about 1999 Cadillac Eldorado

2 Answers

Water poring out of the overflow

I had a new oil pan gasket put on and now i have water pouring out of the overflow and it wA
asnt doing it before

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 59 Answers

Need more info, is it doing it when its hot or cold ?is the temp. light on or off?. any codes? check engine light on ? make sure that your fans are plugged in , they might have dissconected them and forgot to plug them i back in

Posted on Jun 03, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Try this website for resolving car problems by downloading a FREE service manual for your vehicle. This is not an owners manual but a factory mechcanic's manual.

http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

Posted on May 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I pour water into my radiator and at the same time I have my oil plug out and I can see the water pouring through the oil pan I believe could ya help me out with this one


If water/coolant is coming out of the oil pan drain you have major problems. Possible internal cracked engine block/cracked cylinder head or bad head gasket.Do not run the engine as this will cause the bearings/motor to seize until it is fixed

Oct 25, 2015 | Cars & Trucks

1 Answer

How do I change oil pan gasget


Jack up truck for safety sake put jack stands under frame . remove all engine oil remove all bolts holding oil pan on if their is not enough room to drop pan you may have to remove bolts holding motor mounts and jack up engine. if front end linkage is still in the way remove linkage. pull oil pan out. check gasket that was between block and oil pan if any stuck to block of engine remove with gasket scraper or wire brush or wire wheel on drill.make sure mating surface is clean put new gasket on new oil pan I like to use a high temp sealer on gasket both sides. Put pan with gasket back in place of old oil pan and tighten all bolts. jack engine down ,replace moter mount bolts replace any linkage you took apart. and dont forget to replace engine oil. make sure oil plug is in pan before pouring oil in . before starting engine check that no oil is leaking than start engine and check for any leaks again if all is good your done. if this was helpful please leave good feed back. A good temp fix on a rusted oil pan is JB weld make sure no oil is on pan clean with towel and rubbing alchol .you may have to drain oil first. if it is rusted badly you may have to use a wire brush on a drill to clean the area to patch. if patched properly it may last for years.

Oct 17, 2014 | 2000 GMC Sierra

1 Answer

How to replace oil pan in 2006 suzuki xl-7


Depends on ease of access. Many oil pans can be dropped without removing the engine. You will have to put car up on ramps and chock the wheels. Set emergency brakes and make sure car is in Park. I know, sounds like overkill, but better to much safety than one deadly accident. Drain your oil pan just like you would to do an oil change. Locate your oil pan bolts and carefully remove them. This should allow the pan to drop free for the gasket to be replaced. The leak may be due to loosened or lost bolts and not a bad gasket. You might try tightening them first and replacing any lost ones. Be sure not to over-tighten or could could bend the pan and that's a whole new bucket of problems. If you do replace the gasket, clean both surfaces, put new gasket on pan with a THIN bead of gasket sealant, put a THIN smear on top of the gasket and put back onto engine block. Tighten bolts to specified torque. May as well put on a new oil filter. No sense keeping cruddy oil filter with new oil. PUT OIL IN ENGINE. Remove from ramp and let run a bit, shut off for 5 minutes and recheck oil level. Be forewarned, this is a really dirty, crungy job. Wear clothes you're not emotionally attached to. Have hot water and dish soap at the ready to clean-up. No body wants to grab a door knob that's got yucky motor oil on it. And jump straight to the shower.

Apr 28, 2014 | 1995 Buick Century

1 Answer

Replaced oil pan gasket on and now oil is pouring out when the engine is off


Did you use a torque wrench on the pan bolts? They have to be set to inch pounds of torque, if you over do it or under torque it, there are problems.

Feb 17, 2014 | 2000 Chevrolet Silverado 1500

1 Answer

How to change transmission oil


purchace a new pan gasket and filter . put car on hoist . remove pan bolts use a screw driver pry pan carrfully from trans mission being careful not to bend pan edge [gasket seals there] pour oil from pan into pail with out spilling . wipe floor of any drips so you dont slip . remove filter 2 bolts normaly replace filter make sure o ring if it has one hasnt fallen out . clean and replace pan torque bolts to 28ft lbs . lower car fill with 3 liters oil start, idle ,check level add till full dont over fill dont hurry . let run for a bit look under car foe any leaks this is a basic trans filter oil change for all makes.

Nov 21, 2013 | 2005 Peugeot 407 2.0

2 Answers

I have brown coolant and little heat I have flushed 3 times and still comes back brown. why is there brown still in the heater core and how do I get it out and could it cause my overflow problem I...


To me it sound like you have oil getting into your radiator fluid either from engine or transmission lines..As for the overflow problem make sure the fan is coming on when it gets hot..It could be water pump or radiator or thermostat

Jun 11, 2011 | 1998 Mercury Sable

1 Answer

My radiator was leaking and had oil in it so i had to flush it out unexpectedly the same night a cold front moved an it froze what little water an oil was in it, i dont think there was enough to crack the...


Unless you drained the water from your block directly, you would have had about 2/3rds of your total water still in the engine. So if it got down below freezing then it doesn't look like your going to be using that engine anymore. Sorry to be the bearer of bad news. Unless I'm miss understanding and you did pull the plugs on your block, then you may come out okay.

Feb 08, 2011 | 1998 Ford Expedition

1 Answer

Where is the oil pump located on a 1999 ford taurus and whats items do i need replace a long with the oil pump


Remove oil pan oil pump and pick up tube & screen will be bolted on.
You should get oil pump lube, carb. cleaner, new pump oil,
oil pan gasket, silicon, oil & filter, loc-tight, gasket remover & tools metric, 1/4 drive socket set, scraper / putty knife, 2 jack stands, a jack or ramps,
& blocks for rear wheels.
Lets get started.

(1)Get your car up on stands or ramps block rear tires.

(2)Drain oil & remove oil filter remove battery cable NEG (-)

(3)remove pan

(4)remove old pump

(5)remove pick up tube from oil pump

(6)Now clean tube & screen with carb. cleaner place on news paper to dry.

(7) clean all old gasket off from engine & pan also clean bolts

(8)place silicon on pan place gasket on pan put bolts in from gasket side to Aline holes put a side to dry

(9) Attach tube to pump with a little loc-tight fill pump with oil pump lube

(10)attach pump to engine block make sure rod goes in proper & bolt are tight.

(11)Bolt pan back on engine using a 1/4 in drive ratchet don't over tighten bolts get all bolts in now slow run each bolt in starting at 1 end then jump to the other then go to bolt at other end a cross from 1st bolt. Do this till all bolts are ran in. Now tighten bolts look for gasket on side of pan.If it starts to push out stop go to next bolt.

(12)Instill new filter & drain plug,& pour in oil

(13)Replace Neg - cable

I hope this works for you it's a basic oil pump change for most cars.
Some take more steps.

Jul 14, 2010 | 1999 Ford Taurus

Not finding what you are looking for?
1999 Cadillac Eldorado Logo

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...