Question about Pontiac Grand Am

1 Answer

How do i remove the old glass clips that are glued to the window

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,865 Answers

Use a blow dryer to heat up the glue and then remove the clips with a putty knife. Joe

Posted on May 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bought window regulator for 2000 Olds Alero but plastic clip that is attached to bracket and glues to window is broken . So can't connect regulator to clip . Can clip be replaced ? How can old clip that's...


Replacement clips are available through specialty auto parts stores...there are many tricks or solvents that will loosen the glue on the broken clip...if you damage the glass, you can find a popular window replacement, inspect the clip too, at your nearby salvage yard or online...Hope this helps.

Nov 06, 2013 | 2000 Oldsmobile Alero

1 Answer

What holds the glass on the tracks for a 1985 olds calais crank window


Window Regulator holds the actual rail, the glass
is pressed & glued into
There are no tracks,you can see where the window
slides on the front & back edges
Best to remove the inner door panel & get to the
heart of the problem

Jul 11, 2013 | Cars & Trucks

1 Answer

The brackets that attach to the driver's window on my son's 2003 Grand Am have broken due to forcing a frozen window. The window is no longer attached to the slide mechanisms. I am wondering...


Hello, normally just the window sashes break. this is the plastic part that is glued on the bottom of the glass. you can but these asahes at your dealer. they simply just glue on with a special glue

Sash Channel Came Off Glass; Adhesive on Glass
  1. Remove the door glass and lay it on a protected table.
  2. Mark the location of the clip with tape.
  3. Remove the adhesive with a one edge razor blade.
  4. Clean the glass with Isopropyl alcohol.
  5. Important: Install adhesive into the applicator and squeeze some adhesive out before you install the mixing tube. After the mixing tube is installed, run a test bead the length of the mixing tube to ensure a good mix.
  6. Fill the sash channel clip with adhesive.
  7. Install the clip in the marked location.
  8. Reinstall the door glass and put the glass in the full up position for 24 hours.

Cut off the bottom edge of the guide with a cut off wheel. (Refer to the illustration above.)

Using a thin flat blade putty knife and a hammer, carefully remove the plastic piece on each side of the glass. (Refer to the illustration above).

  • Clean any adhesive from the glass using a one-edge razor blade. (Refer to the illustration above).
  • Clean the glass with Isopropyl alcohol.
  • Important: Install adhesive into the applicator and squeeze some adhesive out before you install the mixing tube. After the mixing tube is installed, run a test bead the length of the mixing tube to ensure a good mix.
  • Fill the sash channel clip with adhesive.
  • Install the clip in the marked location.
  • Reinstall the door glass and put the glass in the full up position for 24 hours.

  • 22689012
    Sash, Side Door Window
    12378568 (US)
    88901676 (Canada)
    Structural Urethane Installation Adhesive
    mrtechwrench_28.gif

    Jun 06, 2011 | 2003 Pontiac Grand Am

    1 Answer

    Rear window down by driver but push button to raise it & grinds & doesn't go up. Looking @ window it can be pulled up almost all the way & can see that there scuffs on the glass. Attempted to...


    Sounds like you have a window regulator problem. Most door panels are held on by screws and plastic pop clips. I am not sure what type of vehicle you have. Once the door panel is off you can support the glass in the up position and replace the regulator assembly. Most are bolted in and some are rivioted which means you will have to drill out the old riviots and install new ones that need a special riviot gun

    Sep 05, 2010 | Buick LaCrosse Cars & Trucks

    1 Answer

    Window clips


    how do i get the old glass clips off that are glued to the window

    Apr 02, 2010 | 2003 Pontiac Grand Am

    2 Answers

    Driver side power window is not connected to


    Easy dont access nothing its a grad am you could do more harm then you know have it serviced by someone who installs autoglass they have more expieriance

    Apr 01, 2010 | 1999 Pontiac Grand Am GT

    1 Answer

    Driver's door glass pulls out of regulator clips,glued them with windshield sealent.Still pulled out.1998 ford explorer/Power windows. What could be wrong,window track not bent..have you heard of this...


    am not familiar with that model but if the glass sits in a track (Steel with rubber lined) then the glass has to be removed and the track "beaten" onto the galss, Try at your peril as it is easy to shatter the glass if not done properly. You must use a rubber hammer.

    Most window glass units are bolted to the rail but you do not mention this.

    Nov 30, 2009 | 1998 Ford Explorer

    1 Answer

    Need to remove window from regulator


    they are clipped on/ in a channel

    Jan 25, 2009 | 2008 Chevrolet Equinox

    2 Answers

    How do you remove interior rear view mirror on 1998 Buick Regal


    It is held on by a spring tension clip, use a jewlers screwdriver to release it.

    Nov 14, 2008 | 1988 Buick Regal

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    27 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Pontiac Experts

    yadayada
    yadayada

    Level 3 Expert

    75807 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22133 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8172 Answers

    Are you a Pontiac Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...