Question about 2001 Chevrolet Silverado 1500

1 Answer

Replacing speakers What are the steps for removing panels and replacing the front and rear in-door speakers.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Try this website for resolving car problems by downloading a FREE service manual for your vehicle. This is not an owners manual but a factory mechcanic's manual.

http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

Posted on May 01, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2039 Answers

SOURCE: removing the front door panel

there a special tool to remove that clip or you can use a women nylon slip the nylon beetween the handle and door panel and move it be carefull that clip fly off when it loose thanks pierre

Posted on Oct 19, 2008

  • 203 Answers

SOURCE: Replace speaker in passenger door

there is normally a couple of screws around the door handle they might be covered with blank offs. they will look like discs remove them and undo screws. then start pulling panel gently from bottom right hand corner to remove clips. oh and if you have a manual winder winder or electric they will have to be removed too.

Posted on Dec 28, 2008

  • 1986 Answers

SOURCE: Front door speakers

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 255 Answers

SOURCE: how to remove rear door interior door panel

You should obtain a tool made specifically for removing door panels. They are attached by "snap" connectors, and by pulling on the door panel itself will invariably ruin it. Get the tool from a parts place and carefully peer into the slot between the door metal and the door panel. Use the tool slowly with resolution. You should really acquire a manual that guides you for your particular Jag.
Remember, to take the panel completely off, you need to remove the door handle. Look for a plug that has a screw under it. You'll need to pop the door window/lock control panel too, to access screws under there. This can be tricky, so be careful.

Posted on Nov 24, 2009

  • 54 Answers

SOURCE: how to remove front and

go to auto parts store or retail store to get a tool called panel popper. it has 2 prongs shaped like a wrench on a shaft (like a screw driver). check panel for screws to remove and after remove screws, use panel popper to pry the panel up. put the panel popper near the plastic tabs that hold the door in place.

Posted on Sep 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.


Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942). Refer to Section 01-05.
  1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
  1. Remove two screws from cover assembly.
  1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
  1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


an0786b.gif


Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal
  1. Remove cover behind inside door handle.
  1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
  1. Remove three screws retaining front door trim panel to front door.
  1. NOTE: Do not attempt to remove more than one pushpin at a time.

    Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
  1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
Installation
  1. Follow removal procedure in reverse order.
  1. Replace all pushpins with new pushpins (N808994-S).
Front Door Trim Panel


ar0318d.gif

Jan 14, 2011 | 1999 Ford Taurus

1 Answer

How do I replace speakers on a 1994 xj6 ?


Replacement of Front and Rear Door Speakers

Required Tools:

#2 Phillips Screwdriver (magnetic tip is useful)
9 mm Nut Driver
8” or 10” Flat Tip Screwdriver
Small awl or other sharp pointed instrument
Soldering Iron w/solder or 8 to 10 small wire **** splices
8 to 10 small machine screws -- #8 x ¾” or equivalent 8 to 10 small machine screw nuts & flat washers to match
Thread locking compound “Loctite” (optional)
6” wooden dowel of ½” diameter to be used as a drift
Small mallet or hammer

1) Whenever you are attempting to a remove door panel to gain access to the speaker, or any other electrical component, absolutely disconnect the negative battery cable. Battery power is supplied to each door window motor and it’s always prudent to de-energize these circuits before you attempt any panel work.

2) XJ40 door inner panels (front or rear) are comprised of an upper and lower section, which interface to provide complete inner door coverage. Neither panel is difficult to remove nor are any specialized tools required.


3) Remove the Upper Inner Door Panels as follows:

It’s a good idea to store all the removed parts and screws in the adjacent foot well for safekeeping and easy access when you are putting everything back together.

a) Using a small awl (or equivalent), remove the small “square” plastic cover for the inner door lock release mechanism (upper right side when facing inner side of door). It pivots towards the front of the car.

b) Using the #2 Phillips screwdriver, remove the inner door lock release mechanism plastic / chrome escutcheon. It’s held in place by a single machine screw. Pull out on the door lock release mechanism and the escutcheon is easily removed.

c) Using both hands, pull out on the wood veneer panel at the inner door lock release mechanism to provide clearance and slide the panel towards the front of the car. The panel is secured on the left side by slip-in clips and they release easily.

d) Using the #2 Phillips screwdriver, remove the two sheet metal screws on the left side. For the front doors only, lift the bottom of the rubber ventilation boot at the front edge of the door and remove the sheet metal screw. Additionally, for the front door only, use the large flat screwdriver as a lever to ease out the single “fir tree” type press-fit connector. Neither of the rear doors contains these two additional fasteners.

e) Using both hands, lift the upper inner door panel until it releases from the metal ridge along the window line. It doesn’t take much effort to remove the upper panel as it slides off vertically. Store it on the seats for safekeeping.

4) Remove the Lower Inner Door Panels as follows:

a) Using the #2 Phillips screwdriver, remove the sheet metal screw located at the upper edge of the lower panel.

b) Using a ½”small wooden dowel or equivalent drift, place it under the lower edge of the door handle screw access cover. Lightly tap each end of the access cover using the dowel and mallet in an upward direction to release the access cover. These covers can be tight if they have never been removed in the past, but they will release.

c) Using the #2 Phillips screwdriver, remove the sheet metal screw located in the middle of the door handle.

d) Using a small awl or equivalent, remove the bottom door light lens by releasing it from its locator at the rear and sliding it outwards from the door.

e) Using the #2 Phillips screwdriver, remove the lower panel securing sheet metal screw located in the middle of the bottom door light assembly. All sheet metal screw fasteners for the lower panel are now removed.

f) Using both hands (and the large flat screwdriver, if needed), carefully pull off the lower inner door panel by release the series of fir-tree type press-fit connectors along the sides and lower perimeter. Once the panel is removed, it can be laid horizontally on the seat as there is sufficient length of wire bundle to allow this movement. It is not necessary to disconnect the wiring harness, but if desired, the connectors can be released so that the panel can be moved to another more worker friendly location.

5) Remove Door Mounted Speaker as follows:

a) Disconnect the speaker positive and negative conductors by releasing the electrical connector.

b) Using the 9mm Nutdriver, remove the speed clip nut from each of the four (4) speaker fastener studs. Press the nutdriver down firmly to engage the speed nut … do NOT cut away any foam material as it is not necessary.

c) Using the #2 Phillips screwdriver, remove the sheet metal screw immediately to the left (driver side) or right (passenger side) of the speaker as viewed from the back side of the door lower inner panel.

d) Using the #2 Phillips screwdriver, remove the sheet metal screw immediately above the speaker. It is located just below the upper sheet metal screw securing tab on the lower panel … the screw was previously removed in Step 4a.

e) Using the #2 Phillips screwdriver, remove the sheet metal screw immediately to the lower right (driver side) or lower left (passenger side) of the speaker as viewed from the back side of the door lower inner panel.

f) Using the #2 Phillips screwdriver, remove the sheet metal screw immediately to the lower far right (driver side) or lower far left (passenger side) of the speaker as viewed from the back side of the door lower inner panel.

g) Steps 5c, d, e and f will release the speaker / window lift pushbutton panel from the lower door inner panel. Removal of the sheet metal screws will allow the speaker panel to be pulled away from the lower panel by 3” to 4” to facilitate access for speaker removal.

h) With the speaker / window lift pushbutton panel eased back for working clearance, grasp the speaker with one hand while pressing the four (4) speaker studs downward through the foam supporting material. After the studs are clear from the foam material, the speaker can be removed from the panel.

6) Install New Door Mounted Speaker as follows:

Typically, base XJ40 models use 3.5” door speakers while the VDPs will use 4” door speakers. Though I believe it is possible to mount either type in either model.

a) Using the wiring supplied with the new speakers and insulated solderless **** splices, transfer the old speaker wiring electrical connector to the new speaker. Another alternate method is to simply solder the old speaker wires with connector to the new speaker terminals. This is a superior method for electrical continuity and strength of joint … although it does require some soldering skills.

b) Install the new 3.5” speaker by easing back the speaker panel and sliding in the new speaker. Normally, the 3.5” models will mount with only two fasteners.

c) Using two of the small machine screws with flat washers, place these fasteners through the speaker mounting lugs and press them up through the existing holes in the foam supporting material. Secure the screws with flat washers and matching nuts from the back side of the inner door panel. The use of thread locking compound (Loctite) is a nice touch to prevent loosening due to vibration.

d) Re-install the sheet metal screws removed in Steps 5c, d, e and f. This will re-mount the speaker panel. Don’t forget to re-connect the speaker wire connector at the door panel.


7) Re-installation of the inner door lower and upper panels is literally a reverse of the removal procedure. No hidden tricks.

8) Perform Steps 3 through 6 for the other doors and the job is complete.

9) Remove Rear Footwell Mounted Speaker as follows:

This sequence is good for both 4” and 5.25” footwell mounted woofers.

a) Using a small flat screwdriver as a lever, carefully ease off the grill.

b) Using a #2 Phillips screwdriver, remove the four (4) sheet metal mounting screws.

c) Ease out the old speaker and release the electrical connector for the speaker wires.

d) Transfer the old speaker wires and electrical connector to the new speaker using solderless **** splices or by soldering the old leads to the new speaker terminals.

e) Re-connect the speaker wires to the harness by joining the electrical connector.

f) Mount the new speaker and re-attach the necessary sheet metal screws.

g) Press the speaker grill into place.

h) Repeat Steps 9a though 9g for the other footwell speaker.

Mar 10, 2010 | 1994 Jaguar XJ6

1 Answer

How is the rear speaker cover removed from a supercab fx4 f150 2004


The rear door panels are not like the front doors ( additional panel on the door panel ), the silver/gray rear speaker panel is part of the rear door panel.

Remove the panels next to the window ( should be spring clips ).
This should expose 3 bolts holding the top of the door panel on.

Next remove the rear window console panel ( spring clips on the side towards the cab, tabs on the side towards the door ).
Behind this should be a bolt.
Next remove the rectangle cover in teh door handle area, there is a bolt behind this.
should be 1 other screw at the bottom of the door panel, by the door sill area ( under the map pocket ).
The door is held on like the front doors, with large plastic hooks, so pick up on the door panel once all the screws are out.

Nov 24, 2009 | 2004 Ford F150

2 Answers

I am looking for a diagram or picture as to how to get to the speakers to replace them on a 97 villager??


Section 15-03: Speakers 1997 Villager Workshop Manual DESCRIPTION AND OPERATION Radio Speakers All vehicle sound systems are equipped with radio speakers (18808) located at all four corners of the vehicle. The radio speakers are mounted in the RH front door (20124) and LH front door (20125), as well as behind the quarter trim panels (31012) in the rear of the vehicle. The Ford Super Sound Audio System has the addition of a subwoofer mounted in the RH quarter trim panel.
-----------------------------------------------------------------------------------------
Radio Speakers, Front Door Removal
  1. Remove the front door trim panel (23942). Refer to Section 01-05 .
Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  2. svv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).
  3. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screw from the door pull handle.
  2. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  3. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
  4. Remove the front door trim panel.

Door Electrical Connections
Removal and Installation
Refer to Section 01-11 for Power Window, Section 01-09 for Power Mirror, or Section 01-14B for Power Locks. Watershield
Removal
  1. Remove the Front Door Trim Panel . Refer to the removal procedure in this section.
  1. Remove the front door watershield by carefully detaching it from the adhesive.
  1. Remove the four front door radio speaker screws.

May 20, 2009 | 1997 Mercury Villager

1 Answer

Replace driver side mirror on 2001 Nissan Quest


SECTION 501-09: Rear View Mirrors 2001 Villager Workshop Manual REMOVAL AND INSTALLATION Mirror —Exterior Rear View Removal
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the upper speaker.
    1. Disconnect the electrical connector.
    1. Remove the bolts.
    1. Remove the speaker.
  1. Position the watershield aside.
  1. Remove the exterior rear view mirror access panel.
  1. Disconnect the exterior rear view mirror electrical connectors.
    • Release the wiring harness locator.
  1. Remove the exterior rear view mirror.
    • Remove the bolts.
    • Feed the wiring harness through the door opening.

Mar 31, 2009 | 2001 Nissan Quest

1 Answer

HOW DO I REMOVE rear speaker panels from 1994 celica???


  • remove the hinged brackets for rear seats remove locking bracket too
  • open front door carfully pull up plastic scuff plate
  • lift rear seat (push clip in centre of each seat)
  • push back the panel hard from door piller
  • pull panel out at bottom and puch down top of panel.Pig of a job but can be done.

Feb 15, 2009 | 1994 Toyota Celica

2 Answers

Speakers


This is a partial solution to let you know that the door panels for both the front and rear speakers have to be removed,, See repair manual for removing the door panels

Dec 15, 2008 | 1999 Volkswagen Passat

1 Answer

Replace speakers on Ford Explorer Sport Trac


The front and rear door panels must be removed. The interior door handle will have to be removed, and the power window switch will also have be removed. This is held in by metal clips that secure it to the door panel. Do not be afraid to use a little force to get under the switch panel, and pry it from the door panel. Once you have all accessories off of the door panel, look for what may appear to be "plugs" in the door panel. These may conceal the presence of a screw. Also, check around the interior door pull for screws or "plugs". When this is done, use a medium to large screwdriver, or a trim removal tool, and start prying the door panel away from the door. Start at the bottom, and work your way around the door, until you get about 2-3 inches from the top of the panel where it meets the window. When you are at this point front and rear, simply lift up on the door panel, and it should come off easily. Once the panel is removed, you will easily find the speakers.

Nov 11, 2008 | 2005 Ford Explorer Sport Trac

2 Answers

Replace speakers on 95 camry


Remove the inner door handle. Remove the plugs that hide the door panel bolts, remove the bolts. If the panel has a light at the bottom edge, pull it out & disconnect it. Remove the 2 trim plugs from the latch side of the panel. Remove the 2 screws at the fron edge that are under plastic covers. Remove the window master switch and unplug it. Starting at the bottom, pull the panel off. The rear speakers may be a bit more difficult; if you can get to them from inside the trunk, good. If not, you have to pull out the rear seat, back and bottom. Remove the rear finishes from beside the seat. Remove the C pillar trims, and pull the rear shelf out in front of the back glass. Replace the speakers.

Sep 10, 2008 | 1994 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

277 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...