Question about 1999 Nissan Altima

1 Answer

None of the power windows work.No local or master controls work.

None of the power windows work.local or master control.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 82 Answers

Start by checking fuses, then relays. if the main switch goes on driver's door goes out then none of them will work.... i would recommend a new switch not a used one.

Posted on May 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What could cause my power windows not to work?


Usually it is in the drivers window controller.There is a module that usually goes bad.

Dec 14, 2014 | Cars & Trucks

1 Answer

I have a 2002 chrysler 300m, none of my power windows work


u need to start by checking the fuses. U didn't say if u checked all the switches on the doors themselves. If the door switch will work then your problem will be with the master control on drivers door. Hope this helps

Mar 15, 2014 | 2002 Chrysler 300M

1 Answer

Power windows locks and mirrors


Sounds like the master switch is not plugged in properly, this is the switch in the driver's door.

Jun 07, 2012 | Cars & Trucks

1 Answer

Windows only work from the drivers door controls


Check the master window control panel on the driver's door. There is probably a lockout switch. It may have a window outline on one end and the same outline with an "X" over it on the other. Press the outline without the "X" and all your windows should work again. As silly as that sounds, a lot of people hit that switch without knowing it. Also, if that switch(lockout) is faulty, none of the windows will work. That happens A LOT!!

Window fuse's and relay's may be up under driver or passenger side dash or behind glove box, under the hood and even under the seats, and finally on the ends of the dash. All passenger power windows and locks are controlled thru and get power from the master control switch on the drivers door.

Aug 26, 2011 | Dodge Stratus Cars & Trucks

1 Answer

None of my power windows work in my 2000 concord. They all failed at once. I see the 20amp BRKR for the power windows and have tested it and its ok. But there must be another fuse somewhere and my manual...


There is usually a master control where the driver can control all windows. I would look there next. Make sure you have 12 volts on one side of the fuse, if the fuse is good then you know 12V is on the other pin when it is inserted and should be going to the master control. You have a common fault killing all windows and I would suspect something awry in the master control. I have disassembled those switches and cleaned the contacts, reassembled them and had them work fine. Use emery boards and pencil erasers as your most abrasive cleaning agents. You may want to take a look on ebay and buy a used one for a few bucks and practice on that.

Mar 30, 2011 | Chrysler Concorde Cars & Trucks

2 Answers

91 4runner power window fuse s are good but none of the door windows work and only the passenger power door lock works


replace the power window master switch and chances are the lock actuators are bad. replace as neccessary. happy holidays

Dec 28, 2009 | 1991 Toyota 4Runner

1 Answer

All power windows inoperative


Check the wiring bundle going into the drivers door by pulling back the rubber cover look for broken wires, all window controls pass through the drivers door before going to the others.
My local salvage yard was able to fix me up with a good useable bundle.
Jeep dealer was not able to get it.

Apr 11, 2009 | 1994 Jeep Grand Cherokee

2 Answers

Power windows/ door locks


you might have left your window cracked and it rained on it, or it could have gone out on its own but it is definately the master control switch, on drivers door needs replacing. hope it helped you.

Oct 29, 2008 | 2005 Chevrolet Silverado

Not finding what you are looking for?
1999 Nissan Altima Logo

285 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...