Question about 2005 Hyundai Elantra

Open Question

How to change pvc valve on hyundai 2005 elantra

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

michigan man
  • 3533 Answers

SOURCE: oil change procedure on a 2005 Hyundai elantra

it is very easy to change the oil put the car on ramps secure the back end look for the drain plug underneath the engine make sure you have the right size wrench and when you remove the plug also check the gasket on the plug to make sure it is not cracked you will also need an oil filter wrench and my other suggestion to you is to go to autozone to see if they have a Haynes repair manual for your car and if they don't see if they can order you one in the mean time they can also print you off a diagram of how to change the oil in you car safely

Posted on Jan 20, 2009

  • 187 Answers

SOURCE: front wheel bearing

This job is more than a none mechanic is able to do easily.

Posted on May 09, 2009

motor1258
  • 6674 Answers

SOURCE: problems rplacing car stero

Check all your fuse in dash & under hood for a blown one.

Posted on Jun 20, 2009

canbruce75
  • 1776 Answers

SOURCE: how to replace the battery on a 2005 hyundai

If you purchase a new battery at an autoparts store, like autozone or advance, they will install the new battery for you. Hope this helped and best wishes.

Posted on Jul 31, 2009

ZJLimited
  • 17970 Answers

SOURCE: need fil for error code P2626 Hyundai Elantra GLS

P2626 O2 Sensor Pumping Current Trim Circuit/Open (Bank 1 Sensor 1)

I'll sure this has to do with a faulty O2 sensor. This sensor is usually located around the header of your car, or down more on your exhaust.

Try disconnecting your battery for 30 mins, hook it back up, and start your car again. This will erase the error. See if it comes in again.

Hope this help (remember rated this post).

Posted on Mar 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace pcv valve


Here's a video showing you how to replace your pvc valve. How to replace PCV valve in 2006 Hyundai Sonata

Jul 26, 2015 | 2005 Hyundai Sonata

1 Answer

Can't get valve cover off to replace the PVC valve.


RECHECK MAKE SURE ALL VALVE COVER BOLTS BEEN REMOVED. LOOK AT THE NEW VALVE COVER GASKET COUNT BOLT HOLES IN NEW GASKET IF YOU COUNT SAME AMOUNT BOLT HAS BEEN REMOVED. VALVE COVER STUCK TAKE A RUBBER HAMMER TAP VALVE COVER TO BREAK THE SEAL.DONT PRY VALVE COVER YOU WILL DAMAGE VALVE COVER AND SEAL SURFACE CAUSING YOU TO GET A OIL LEAK.

Aug 09, 2011 | 2008 Hyundai Elantra

1 Answer

2005 elantra not an idiot but cannot find the thermastat to replace it is it well hidden followed all the large hoses HELPchipt


Remove the radiator hose from the thermostat housing cover by removing the band clamp that holds the hose to the cover. This is done with a Phillips screwdriver. Slide the band clamp back away from the housing and pull the hose off.


  • 2 Remove the two bolts that hold the thermostat housing cover to the top of the Elantra intake manifold with an adjustable wrench. The bolts will be reused. They should not be discarded.


  • 3 Remove the old gasket that was pressed between the intake manifold and the thermostat housing cover. It's a paper gasket and should pull off of the intake in one piece. Remove the thermostat from inside of the intake manifold by pulling up on it. The gasket and thermostat can be discarded.

  • 4 Place the new thermostat into the intake manifold of the Hyundai Elantra. The thermostat must be placed with the top sticking out of the intake manifold for it to work properly. Use the old thermostat to orientate the new one.

  • 5 Place a small amount of PVC gasket sealer around the thermostat on the base of the intake manifold. Allow the PVC to dry for ten minutes and then place the thermostat gasket on top of the gasket sealer. Place a small amount of PVC gasket sealer on top of the paper gasket and allow to dry for ten minutes.

  • 6 Place the thermostat housing cover onto the gasket and bolt it into place with the original bolts. You should see a small amount of PVC gasket sealer squeeze out between the housing and the intake. This is normal and it should be left in place. Once it dries, it will add additional seal protection and prevent leaking.

  • 7 Place the radiator hose back on to the thermostat housing cover and fix it into place by tightening the band clamp with a screw driver. Your Hyundai Elantra is now ready to drive again.

  • In case of a problem or clarification or my solution was insufficient, don't hesitate to post me a reply.

    If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.

    May 30, 2011 | Hyundai Elantra Cars & Trucks

    1 Answer

    Can you please tell me where the pcv valve is located on a 2004 hyundai elantra ? Thank you


    most pvc valves are located in the valve cover, i believe yours is right on top, it has a hose going to the throttle body area

    Mar 28, 2011 | Hyundai Elantra Cars & Trucks

    2 Answers

    How do i replace the thermostat


    Follow this steps on how you can replace the thermostat. First,Remove the radiator hose from the thermostat housing cover by removing the bandclamp that holds the hose to the cover. This is done with a Phillipsscrewdriver. Slide the band clamp back away from the housing and pull the hoseoff. Remove the two bolts that hold the thermostat housing cover to the top ofthe Elantra intake manifold with an adjustable wrench. The bolts will bereused. They should not be discarded. Remove the old gasket that was pressed between the intake manifoldand the thermostat housing cover. It's a paper gasket and should pull off ofthe intake in one piece. Remove the thermostat from inside of the intakemanifold by pulling up on it. The gasket and thermostat can be discarded. Placethe new thermostat into the intake manifold of the Hyundai Elantra. Thethermostat must be placed with the top sticking out of the intake manifold forit to work properly. Use the old thermostat to orientate the new one. Place a small amount of PVC gasket sealer around the thermostat onthe base of the intake manifold. Allow the PVC to dry for ten minutes and thenplace the thermostat gasket on top of the gasket sealer. Place a small amountof PVC gasket sealer on top of the paper gasket and allow to dry for tenminutes. Place the thermostat housing cover onto the gasket and bolt it intoplace with the original bolts. You should see a small amount of PVC gasketsealer squeeze out between the housing and the intake. This is normal and itshould be left in place. Once it dries, it will add additional seal protectionand prevent leaking. Place the radiator hose back on to the thermostat housing cover andfix it into place by tightening the band clamp with a screw driver. YourHyundai Elantra is now ready to drive again. Hope this info help you.

    Jan 25, 2011 | 2005 Hyundai Elantra

    1 Answer

    I just want to know where the transmission filter is on a 2005 Hyundai Elantra and how often the filter and fluid need changing?


    Most Japanese/Korean made cars actually have no transmission filter...such as hyundai, toyota, honda. Fluid changes should be listed in your owners manual...I think its between 60,000-80,000kms...but I changed mine earlier in my elantra and added in some Lucas for trannys since I noticed mine shifting hard between second and third...cleared it up.

    Aug 05, 2010 | 2005 Hyundai Elantra

    2 Answers

    Hyundai troubleshooting code p0010


    P0010 is camshaft position actuator malfunction. Hope that helps

    Jan 15, 2010 | 2004 Hyundai Elantra

    1 Answer

    2005 Hyundai elantra sputters - not all the time - no computer codes - garage replaced spark plugs - then purge valve - same problem. it basically hicups.


    ask what spark plugs they put in your car. bosch platinums and other aftermarket plugs will give you these symptons. stick to the ngk or champions that came stock

    Jul 22, 2009 | 2005 Hyundai Elantra

    1 Answer

    Where is pvc for 97 hyundai elantra


    The PCV valve is located on top of the engine behind the intake. Little white piece with a black hose running out of it.

    Please rate if I helped or solved your problem

    Feb 09, 2009 | 1997 Hyundai Elantra

    1 Answer

    Timing Belt for 05 Hyundai Elantra


    unless your well clued up with engines i wouldn't try changing timing belt yourself get somebody experienced to do this because if you don't time engine up properly you could cause serious damage by bending valves.

    Dec 16, 2008 | 2005 Hyundai Elantra

    Not finding what you are looking for?
    2005 Hyundai Elantra Logo

    Related Topics:

    121 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    75066 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7754 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...