Question about 1997 Ford Escort

1 Answer

Seting timing on transit 2.5 1997 on bottom end

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 22,095 Answers

Pump setting is 8ºbefore tdc used to be a mark on pulley wheel when i built them engines in dagenham in the early 70s ,if no mark visable set crankshaft keyway to the top of the engine and its on the slant remember ,think rheir is a mark on the flywheel now for common rail injection .We used to use a sort of tool that fitted over crank end then we turned it to lock against something which meant the keywaty was pointing to the top of the head and the engine was on a carrier so it sat upright .memorys ,best one was the night shift canteen ,better than a lot of resteurants i have been in since ,real genuine currys and west indian food anywhere

Posted on May 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford transit 2.0 2005 is it a timing chain or belt


google "2005 ford transit does it have timing chain or belt" scroll down to utube and click on the approp video

Jul 18, 2017 | Ford Cars & Trucks

2 Answers

Volvo 940 Troubleshooting


What you are probably hearing is referred to as "piston slap". It occurs over time as the side-to-side motion of the piston as it moves up and down in the cylinder slowly wears the lower walls of the cylinder, changing it more cone-like. This causes the bottom edge of the piston skirt to strike the bottom edge of the piston wall as it transitions from its lowest point to begin its upward stroke. This was a issue on the Volvo Turbo engines. Google it and you will see that they made changes in 1993 to help prevent this. This problem will not go away. Eventually you will break a piston skirt and that will be the end. If you can, get the engine overhauled before the damage is permanent.

Nov 08, 2013 | Cars & Trucks

1 Answer

What is the torque seting for the rear suspension U bolts on a 1996 Ford Transit, plus the torque setings for the wheel nuts for same moter


Tighten the U-bolt nuts evenly in a cross-type pattern with the weight of the vehicle on it's wheels (not jacked up it means)
Tighten the U-bolts nuts to 125 Nm (92 lb-ft).
Wheel nuts
200 Newton meters

Jun 21, 2011 | Ford Transit Connect Cars & Trucks

2 Answers

I Have a ticking sound from under the bonnet and it sounds a bit like i am driving a Transit Van from inside


If its really loud and sounds like a transit then the bottom end is knocking so the egine is pretty much no good.

If its a slight ticking noise higher pitch then its the hydrolic tappets can be fixed but depends how bad they are they might have to be replaced.

Also check the oil level. is it a zetec? petrol or diesel?

Jan 20, 2010 | 2007 Ford Focus (3 Door) Hatchback

1 Answer

How to align timing gears on 1987 chev. nova


Seting timeing Bottom gear go straight up top gear sets about 2oclock theres a small hole in the gear too line up with a hole in the head use a small drill bit to check this.

Jan 01, 2010 | 1987 Chevrolet Nova

1 Answer

2003 toyota corolla axle replacement


There is a little spring loaded clip on the end of the axle in the trans. Just uses a pry bar against the trans housing and inner axle joint to pop the axle out.

Apr 03, 2009 | 2003 Toyota Corolla

2 Answers

Diagram of Location of a Starter Motor on Ford Transit 2002/2003


i have a 2001y reg transit tipper and i think the starter motor is going when i go to start it like grinds then some times it starts perfect

Nov 24, 2008 | Ford Festiva Cars & Trucks

Not finding what you are looking for?
1997 Ford Escort Logo

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...