Question about 1997 Plymouth Neon

1 Answer

What is the torque on a head for a1997 plymouth neon

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 47 Answers

After removing the head bolts you should use new ones, torque specs will be with the new bolts. Also make sure you run a tap through the block and lubricate head bolts prior to installation for better torque accuracy.

Posted on May 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is it hard to fix a fuel filter on a 1996 Plymouth neon single over head cam


Fix ? You mean replace ! An not hard to replace , may need special tool's to do it . Look on youtube , may be a video showing how to do it. How to Replace Fuel Filter on 1997 Neon Plymouth

Mar 02, 2017 | 1996 Plymouth Neon

1 Answer

How do you align the torque converter to the motor of a 2000 plymouth neon 2.0L with transmission still in the vehicle without it binding?


The trick is to place the torque converter onto the gear box first and slide it back to the gear box. position the gear box against the engine housing and do up the bolts. Then through the inspection cover opening pull the converter up to the flex plate align the bolt holes ,insert the bolts and tension up

Oct 12, 2013 | 2000 Plymouth Neon

1 Answer

Where is the torque converter clutch solenoid located on a 2000 Plymouth Neon?


I think it's right by the bell housing. There is a plug-in going to it. Raise the hood and look straight down to the transmission and you will see it.
_______________
FGTech Galletto 2-Master EOBD2

Sep 11, 2012 | 2000 Plymouth Neon

1 Answer

I just replaced the head in my 99 neon and i'm blowing white smoke from the exhaust. What's the problem


You are burning coolant, the head gasket can be put on Wrong, If your looking at the engine the right rear corner is the only oil passage for the head, you will see a difference in that corner of the head gasket. If your sure that the gasket is on right you may have a warped or cracked head or improper torqued head, all head bolts MUST be replaced when you do a new gasket cause the bolts stretch when torqued. The spec is 25, 50 then 50 then 1/4 turn for the bolt torque.. Make sure u start from the center of the head.

Jun 10, 2012 | 1999 Plymouth Neon

1 Answer

Is there a torque spec for front end cv axle nut to hub on 2000 Plymouth Neon


  • Yes there is a torque spec of 180 foot lbs. is recommended. I highly suggest never using an impact for the hub to axle application. If you don't use a properly calibrated torque wrench you could have problems in the future.

  • Hope this helps.

Nov 04, 2011 | 2000 Plymouth Neon

1 Answer

Does the cv axle nut to hub on front end of 2000 Plymouth Neon have to be torqued to specs to not harm bearing to


  • Yes, a torque spec of 180 foot lbs. is recommended. I highly suggest never using an impact for the hub to axle application. If you don't use a properly calibrated torque wrench you could have problems in the future.

  • hope this helps.

Nov 04, 2011 | 2000 Plymouth Neon

1 Answer

Head bolts torque settings for dogde neon 2002


assuming this is the "C" engine 8th digit on VIN plate. Use new bolts. torque first step to 25lbs, 2nd 50lbs, then 3rd 50lbs, then 1/4 turn.

Sep 23, 2009 | 2002 Dodge Neon

1 Answer

Amount of torque on valve cover bolts


it's 12 nM which appears to convert to about 9 foot lbs of torque.... if your torque wrench has nM use that.

Robert

Please take a moment to rate this solution thanks

Apr 21, 2009 | 1997 Plymouth Neon

Not finding what you are looking for?
1997 Plymouth Neon Logo

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...