Question about 1994 Lincoln Town Car

1 Answer

Replacing the window regulator drivers side on a 1994 town car how dose the glass remove?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Lincoln Master
  • 2,100 Answers

The regulator has two bolts holding the glass, You have to lift the glass up to get to them through the door panel, the whole regulator comes out in one piece. Most cars anyway, I have seen some that just get a belt. Usually the plastic rots off and breaks causing the wires to jump track. Get a wedge of wood ready to hold the glass up after you pull the reg. Then bolt up the new one and bolt the glass back on, the motor knows where to stop. Hope this helps.

Posted on May 01, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i fix power window, motor works wont go up 1994 town car,drivers front

Replace the regulator and motor. Motor has a heat sensor in it. To many amps going up causes heat. It shuts down. The regulator is worn out also.

May 23, 2015 | 1994 Lincoln Town Car

1 Answer

How do I remove a front passenger side window out of a 94 Lincoln Town Car

94 Town Car Window Regulator and Motor this is a video on removing the window regulator. Not sure if it has to come out but this shows you how to unhook it from the regulator. after it is unhooked you can wiggle it around to the right position to pull out the window

Feb 19, 2015 | 1994 Lincoln Town Car

1 Answer

How to take glass out of rear door drivers side?

You have to remove the rubber trim and vent window to be bale to get the door glass out, so you can get the regulator out.
The window is attached to the regulator with two pop rivets that will need to be drilled out. then you have to drill the three rivets that hold the lift motor to the door, drill the two rivets that hold the bottom of the regulator to the door, then you can remove the two 11mm bolts that hold the top to the door. Then you can remove the regulator and lift motor assembly.
Here is a diagram of all the mounting hardware you have to remove to get the regulator out, after you have removed the vent window and rubber seal.

If your car does not have the vent window, then all you have to do to get the glass out is pull the rubber seal around the window out. 17435317-4adb-4cc9-9a5d-653f19be846c.jpg


Sep 11, 2014 | 1997 Lincoln Town Car

1 Answer

I rwplaced the drivers side power window regulator and it goes down fast enough but does strains to go up

The regulator maintains (or regulates) the position of the glass as it goes up or down. The power window motor works less going down because of the weight of the glass, whereas going up if the motor's weak, it'll slow going up and will usually overheat and stop while raising the window if its in need of replacement.

Aug 26, 2011 | 2002 Chrysler Town & Country

2 Answers

The window on the back seat driver's side door slipped down, and the motor seems to be working, but I can't get it to stay up. What needs to be done for me to fix this?

you need to replace the window regulator. these are sold new on eBay and at auto parts stores. when you get it, go to a glass store which also does automotive, they can replace the old with new for about 50 bucks. it really helps to have the tools, fasteners and know how.

Jan 12, 2011 | 1994 Toyota Camry

2 Answers

My drivers side window on my 1994 ford Taurus is stuck in the down position. how do i get it to go up and down again? the window motor is working ok. just that the window will not move

If the motor is working but the glass is not moving something must have broke inside the door. See if you can sneak a piece of duct tape down along side the glass, get it down as far as possible. Use a butter knife or something to make the tape stick to the glass, now try pulling the glass up with the tape. You may want run the window motor at the same time maybe it will catch. If you get the window up, tape it with duct tape so you can get it to a shop to get it fixed. Good luck.

Feb 21, 2010 | 1994 Ford Taurus

1 Answer

1994 cutlass supreme drivers side window will go down but falls off track going up

Normally tracks are not removable. I think you have a window regulator problem. Or the rivits holding the glass in place need to be drilled out and replaced with 1/4 inch bolts and pressure nuts.

Jul 01, 2009 | 1994 Oldsmobile Cutlass

1 Answer

Drivers side window won't go up or down

Have you checked the window regulator. (electric window motor). I seems a comon problem for the plastic to break at the bottom where the wire which pulls the glass up and down. The motor will still sound (clunk) if you use the window switch but will not lift the window.

Remove the trim off the door.
Undo the bolts holding the glass into the plastic at the bottom of the window and carefully remove the glass.
Unbolt and remove the sliding piece that holds the glass.
You should find the broken plastic at the bottom.

Replace and reinstall. Aftermarket parts are available at a fraction of the cost of buying new nissan parts. Second hand parts are available but costly.

Apr 24, 2009 | 1994 Nissan Pathfinder

1 Answer

Replace a window regulator in a 1994 ford explorer

wow, a lot of work to do.

Window Regulator, Front Door, Explorer Removal
  1. Remove front door trim panel and front door trim shield . Refer to Section 01-05B .
  1. Remove inside door belt weatherstrip and glass stabilizer.
  1. Remove front door window glass as described in this section.
  1. Remove two nut and washer assemblies attaching the equalizer bracket.
  1. Remove three rivets (manual) or four rivets (power) attaching the regulator base plate to front door trim panel finish panel (23712) .
  1. Remove window regulator electric drive and front door window channel bracket from vehicle.
  1. Working on a bench, carefully bend tab flat to remove arm slides from front door window channel bracket .
  1. Install new window regulator electric drive arm plastic guides into front door window channel bracket and bend tab back to 90 degrees. Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket . Make sure rubber bumper is installed properly on new front door window channel bracket , if replacement is made.


NOTE: The front door window channel bracket and window regulator electric drive are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Steps 7 and 8 of Window Regulator, Removal.
  1. Install front door trim panel finish panel with preassembled glass bracket into vehicle. Set the regulator base plate to window regulator electric drive using base plate locator tab as a guide.
  1. Install three (manual) or four (power) rivets (385189-S100) to attach regulator to front door trim panel finish panel . Two 1/4-20 x 1-inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (3-5 ft-lb). Equivalent metric retainers may be used.
  1. Install equalizer bracket.
  1. Install inside door belt weatherstrip and glass stabilizer.
  1. Lower regulator arms to access holes in front door trim panel finish panel . Install front door window glass as outlined.
  1. Adjust glass to ensure proper alignment with glass run. Cycle glass for smooth operation.
  1. Install front door trim panel and front door trim shield . Refer to Section 01-05B .

Apr 11, 2009 | 1994 Ford Explorer Limited

1 Answer

How do i remove the passenger window in a 1994 ford probe gt?

Door Glass and Regulator REMOVAL & INSTALLATION
  1. Lower the window glass and remove the inner handle cover, door lock knob (if necessary), the window regulator handle and the door trim panel. NOTE: On vehicles with power windows, disconnect the wiring couplings.
  2. Carefully peel off the door screen so that it can be reused.
  3. Replace the window regulator handle and position the door glass so that the door glass installation bolts can be removed from the service hole.
  4. Remove the door glass installation bolts.
  5. Remove the door glass. Remove the regulator installation bolts, and then remove the regulator through the service access hole. Remove the window motor mounting bolts and separate the motor from the regulator.
  6. Installation is the reverse of the removal procedure. If the vehicle is equipped with power windows, connect the leads of the motor to a battery and run the regulator to the down position before installing the motor. Cycle the window several times to make sure that everything is in good working order.
The door glass retaining bolts can be removed through the access hole


Mar 20, 2009 | 1994 Ford Probe

Not finding what you are looking for?
1994 Lincoln Town Car Logo

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts


Level 3 Expert

76691 Answers


Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides