Question about 2001 BMW 330

1 Answer

Mate.. where do u put it in??? - 2001 BMW 330

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 583 Answers

A foot below the bellybutton from the front

Posted on May 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After relacing clutch assemly on eco sport 2015 has vibration i have line marks on the fly wheel and clutch assemly


AFTER... bummer!

One of your mating surfaces was less than perfect and should have bee resurfaced...

Now they all should be removed & resurfaced.

AND

Until you do so... that vibration will only get worse and put stress on every mating surface, seal and bearing

Sep 29, 2016 | Cars & Trucks

1 Answer

Step by step method on how to put fan belt back on commodore 98


Hi Sharon, The link below is a diagram of pictures for 1998 VT commodore fan belt.........CHEERS MATE..

how to put fan belt back on commodore 98 Google Search

Apr 15, 2016 | 1998 Holden VT Commodore

1 Answer

Me and a mate have been trying to bleed my clutch on my 80 series for 5 hrs and carnt get anywhere. What the hell am I doing wrong? I can do everythingt else other then 1 of the simplist job


Just follow the procedure in the right order. Fill the clutch reservoir on the master cylinder to the max and leave the lid loose. Fit a transparent plastic pipe on the bleed nipple on the clutch slave cylinder bleed nipple. Put the other end of the pipe into a jar to catch the waste fluid. Put some thick grease around the base threads of the bleed nipple, this stops air being sucked in via the threads whne the nipple is slackened off. Loosen the bleed nipple by 1/3 of a turn. Have your mate slowly depress the clutch peddle. When he has reached maximum travel have him hold it there while you turn the bleed nipple a third turn back to tight. Have your mate release the clutch peddle, clutch fluid from the master reservoir should now fill the the master cylinder. Have you mate press the peddle a quarter way and then release the bleed nipple a 1/3 of a turn. Have your mate depress the clutch peddle all the way to maximum travel. Again tighten off the bleed nipple before releasing the clutch peddle. Keep doing this process until no more air bubbles can be seen in the fluid in the pipe attached to the bled nipple. Every four cycles or so check on the fluid level in the master reservoir and keep topped up with fresh fluid. When everything completed tighten the bleed nipple, it is not necessary to tighten the hell out of it as at some point you may need to do this again. Wipe everything down pump the clutch peddle a few times to be sure of correct operation and no leaks.

Jul 01, 2011 | 1991 Toyota Land Cruiser

1 Answer

Thermostat installation


Undue two bolts on thermostat housing - remove thermostat - clean both mating surfaces - put in place new gasket (or RTV gasket material) put in new thermostat (spring down) and replace bolts. Do not over tighten and torque down each bolt alternately using approx the same force you used to remove them.

Nov 28, 2010 | 1988 Chevrolet Suburban

1 Answer

I have a 1996 mustang 4.6. when i start my car it runs at 2000rpm.will finally sttle at 1000rpms after few min. the rpms will not drop when you push in the clutch. just put a new idle air control valve on...


perhaps there is a air leak at the mating surface. if you have a bottle of propane, use it to ckeck for leaks around the gasket/mating surface. start the engine. open the valve on the bottle DO NT LIGHT direct the gas around the mating surface. if the r's go up you have a leak. it is possible that since this is new, the computer was used to the old one and needs time to adjust

Feb 24, 2010 | 1996 Ford Mustang

2 Answers

Dodge neon


drain coolant,follow upper rad hose to thermostat housing,undo hose,therm.cover,take therm.out,clean mating surfaces install new therm.and gasket.

Sep 17, 2009 | 1997 Dodge Neon

1 Answer

I cannot put my car into any gear it wont even move side to side


you poped you linkage mate. its located under the car near the exhuast pipe try to put it back and make an improvise pin to lock it up.

Jul 09, 2009 | 1993 Honda Accord

2 Answers

1984/5 toyota tarago 3y 2litre


1.please check for intake air leak.2.check idle valve condition and power supply to component.3.readout for any dtc in vehicle.

Feb 11, 2009 | 1985 Toyota Passenger

1 Answer

Power steering leak


ok mate ya have a steering use up you need a new power steering box ok thx mate

Nov 16, 2008 | 1993 Toyota 4Runner

Not finding what you are looking for?
2001 BMW 330 Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...