Question about 1993 Mitsubishi Mighty Max

1 Answer

Need to replace clutch control lever. Is this one

Need to replace clutch control lever. Existing one sheared in half. It appears to be one piece... Is this one piece into the trans.?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

Yes. The other half is clipped on a ball or stud, inside the bellhousing. You will need to at least remove the gearbox to replace it. I would also replace the throw out bearing.

Posted on May 01, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you replace sheared bolt on clutch sprocet

Either extract the broken piece with an easy-out or drill and tap a new hole. Or go buy a new refurbished chainsaw and donate that one to a small engine shop.

Feb 15, 2016 | Cars & Trucks

3 Answers

I have a 93 isuzu pick up 5 speed 2.3 carb and went to put it in 1 st gear it felt weird so I let out clutch and nothing and no 2 so I put it in 3 and I have 3 4 5 and reverse there was no noise

what means wired?
NOise what noise?
It would in fact grind gears (will)
TO GEAR, AND you let clutch out too soon, it sure
will grid,, fix the shifter, below.

2wd or 4wd, not stated, and changes labor costs.
and all steps. below.

when you shift to 1st
the transmission is not in first
grab the shifter and shift to 1st ,its loose right, bingo
that is bad parts on bottom of the shifter end.
fixed many.
some have plastic parts here, to stop noise
and excess vibration. they all fail fast.
we replace these
we can also shift to 1st with no shift lever
the acid test, this fails or not. easy no>?
blow more clutches racing then most folks.
do my own work,
mau-5 my guess bingo
msg-5 box?

see photos.
? i can shift from here, photo1
or from extension housing
a- if this is loose shifting will fail.
b- some have plastic tip here, that shatters.
c: on end of extension housing, seen many a time the tip
here near worn badly, to a sliver. and sloppy as heck now, causing shifts to fail.
if the lever feels slooppy ,when not in the center of the H pattern, that be a big problem.!!!!


Jan 15, 2016 | Isuzu Cars & Trucks

2 Answers

Why does clutch pedal go all the way to the floor?

Something has let go. take it back where you got it replaced.

Dec 31, 2015 | 1995 Geo Tracker

1 Answer

Clutch pedal is stuck half way down wont shift gears

Check clutch cable, check clutch lever, if there is some noise from the clutch when the engine is running, then the release bearing is most likely faulty, or even the clutch pressure plate.

Apr 16, 2014 | 1997 Subaru Impreza

1 Answer

Replace transmission

Manual transmission parts:
- Manual transmission, 5-Speed.
- ECM Engine Control, M/T.
- Transmission oil SAE 75W85, 2.5 Litres.
- Clutch pedal assembly.
- Gear lever assembly, with console.
- Gear lever cable set.
- Gear lever boot.

Dec 21, 2013 | 1996 Toyota Corolla

1 Answer

2002 1.3 Kia Rio. Pushed in clutch pedal, heard metallic pop, half a piece of a metal ring + half a clip sitting in driver's footwell. Pedal will depress and release but clutch wont engage

I had this same problem the cable is fine its a clip on outer cable to stop it mooving when you press clutch mine poped when I tightened the clutch cable still don't have solution though waiting to payday to take it to garage

Mar 22, 2012 | 2002 Kia Rio

1 Answer

My turn lever is broken , on the insu=ide of the steering colume, i cannt find and info or part to fix it.

You have more problems than just replacing the lever. There is still a piece of the broken lever inside the wiper switch, and is nearly impossible to get out. You will need to replace both the turn lever and the wiper switch. Replacing the wiper switch is no easy task, and if you are not familiar with General Motors steering columns, it's probably best to pay a shop to do the repair. The top half of the steering column has to be disassembled, and the wiper switch harness fed up through the column.

Aug 21, 2011 | 1998 Pontiac Bonneville

2 Answers

Mrtor running blades are not moving

Check the links inside make sure that they are not broken , if they check ok, your wiper arms are stiped and need to be eather retight or replaced.

Jan 17, 2011 | Hyundai Motor 2004 Sonata

2 Answers

Cavalier won't shift into any gear

There is a pin located on the gear select pin on the transmission side. (the piece the shift cables attach to) the wrist pin is most likely sheared. I have had the same problem.

Jul 09, 2009 | 1999 Chevrolet Cavalier

1 Answer

Replace lever mechnism to recline seat

O'reily stocks a new handle that is especially made to replace the handle that broke. It attaches to the broken shaft you have sticking out of your seat. This is a common problem.

Jun 13, 2009 | 2000 GMC Sonoma Extended Cab

Not finding what you are looking for?
1993 Mitsubishi Mighty Max Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides