Question about 2000 Mercury Cougar

2 Answers

I can`t figure out how to remove the rear seats from my Ford (mercury) Cougar. there seem to be only one clip-like device holding each seat in place,how do I release this..?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You have to to push against the bottom half of the seat towards the back of the car, theres a clip that holds the bar in place and then they just pull out. The top half of the seats have to be unbolted

Posted on May 11, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

First remove the bottom half of the seat. They usually pull up, but they may be fastened by the legs. After removal, you will have access to the bolts on the bottom of the backrest.

Posted on May 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove the rear seat


What type of vehicle? Most rear seats you push down and back on front edge to unlock the clip that holds seat in place, but some have bolts along front edge.

Dec 09, 2014 | Seat Cars & Trucks

1 Answer

Where is the location of the fuel pump driver module on a 2001 mercury cougar


This module is located behind the interior side trim panel, LH side behind the front seat, below the rear LH side glass. AKA B Pillar trim panel. Access from inside, probably will require removal of the rear seat bottom and even top of seat to remove the panel. it will be the small box in the center of that area once the panel is removed. Good luck!

Sep 20, 2014 | 2001 Mercury Cougar

1 Answer

How to remove rear seat of 1997 Mercury Sable


Most rear seats are held in with clams and screws . Look under the swab (bit you sit on) for screws or bolts holding the front of that part down. remove and lift out. Then you should see two more at the bottom of the seat back holding it in . Remove these and lift the back bit straight up off the retaining clips.. take a trip to the wreckers if you are in doubt.

Mar 28, 2013 | Mercury Sable Cars & Trucks

1 Answer

1996 mercury cougar. Where is the fuel pump located? And if its inside the tank how do I remove the tank?


sir you dont remove the tank
you remove underneath the back seat search for any clips screws unfold the seat under it part of the fuel tank and the top of the pump it is a cylindric plastic covers with something like a black or any color disk you turn that disk as the bottle cap

Jun 01, 2011 | Mercury Cougar Cars & Trucks

1 Answer

Is there an emergency gas shut off some where on the gas line? The car ran fine but yesterday it was hit in the rear driver side and when we went to start it up to move it, it puttered, and seemed like...


Check drivers side in trunk behind side panel between rear lights and back seat. There should be a hole to put your finger through and push reset button down. If no hole, you may have to remove any push clips and look behind .

Apr 13, 2011 | 1994 Mercury Cougar

1 Answer

Trunk won't open.


on the front of the seats the bottom part you sit on check for two bolts if it has two remove them if not its easier, either way if there is nothing securing the front down, reach in under the seat between the top and bottom bit where the seat belts stick out of, feel around the middle section and there may be a looped rope material pull it and the bottom seat should just pop straight out, there will be two bolts holding the top part of the seat in, removethese and lift up and farward, the seats till be out,

Jun 22, 2010 | 2000 Mercury Cougar

1 Answer

How to remove a drivers seat


rremove the 2 bolts in front of seat at the bottom and two at the rear bottom of seat then tilt seat and disconnect wiring and remove the seat, good luck, hope this helps.

Dec 19, 2009 | 1999 Mercury Cougar

1 Answer

WHERE IS A FUEL RELAY SWITCH ON A 1997 MERCURY COUGAR XR-7 WITH A 3.8 LITER ENGINE


ford loves to hide those under the drivers seat in a mustang so i would assume the same for yours
remember there is a fuel disconect inside the rear fender well
it is a colision safety device to kill the fuel pump incase of colision

Aug 04, 2009 | 1997 Mercury Cougar XR7

1 Answer

Seat belt chime will not stop until ignition is turned off. mercury cougar 92


the wire under driver seat must have coom loose from the seat belt clip

Dec 04, 2008 | 1992 Mercury Cougar

Not finding what you are looking for?
2000 Mercury Cougar Logo

758 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

fordexpert

Level 3 Expert

5522 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...