Question about 1998 Jeep Grand Cherokee

1 Answer

Disconnected torque shaft at the Torque shaft transfer case bracket. How is it reattached? I've only looked it over under the Jeep and the shaft is disconnected at the bracket. Before I go too far, how is this attached to the bracket? It appears that the shaft has something on the end that should be attached to or pressed into the bracket. The shaft moves freely in this piece when I push it against the bracket and someone moves the shift lever.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Here is a website that a free manual can be down loaded for your vehicle


http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

Posted on May 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Isuzu rodeo 1996 3.2L V6. Torque specs for alternator pivot bolt 14 mm and lock bolt 12mm. torque for AC idler pulley lok nut 23 mm


Isuzu does not list specific torque values for these fasteners. When this is the case, you are expected to use standard torque values. These can be found on the chart I have linked below. Be advised that bolt sizes go by the diameter of the shaft [round shaft portion] of the bolt or stud, NOT the hex head [socket size] of the bolt or nut. Partially remove the bolts so that you can measure the shaft and obtain the correct torque from the chart. See


https://www.swtc.edu/ag_power/diesel_engines/lecture/metric%20torque%20values.pdf

Sep 26, 2014 | 1996 Isuzu Rodeo

2 Answers

Where is the speed sensor?


there several speed sensors 1 on every wheel for abs called wheel speed sensor and in transfer case 4wd or awd call output shaft speed sensor or vehicle speed sensor and input shaft speed sensor which can be a computer generated signal from crankshaft sensor and output shaft speed sensor this is to determine torque converter lock up.

May 16, 2014 | 2004 Jeep Grand Cherokee

1 Answer

How do i get to, or replace the torque converter on my 2004 chevy Trailblazer?


Your torque converter knob fits inside the back of you crank shaft. When you have your transmission off look in the front of you transmission and you will see an input shaft coming out of the transmission. It has a double set of splines on it as well as a front seal. Be very careful when you slide your tourque cover on the shaft that you don't damage that front seal. When you put your torque converter in make sure it lines up on the shafts. You might have to wiggle and play with it a little so it can sit all the way in. After you done that.then slide then trans on the guide bolts. Bolt it down and test it. Look under the trans and find you torque converter and spin it with a coupld fingers. If it does and everything looks good you are set.

Oct 12, 2011 | 2004 Chevrolet TrailBlazer

1 Answer

How to install a clutch kit on my 1994 mitsubishi mighty max


Disconnect the battery, disconnect the Hydraulic Line from the Slave Cylinder, Remove the Starter (2 bolts, 2 wires. Bolts are 14mm, 1 wire is 12mm, 1 plugs in), Remove the Driveshaft(s) (4 12mm bolts) Remove the 6 bolts from the bellhousing (4 are 14mm, 2 are 10mm)
Remove the bolt from the Transfer Case Mount, 12mm (only if it's a 4WD, if it's 2WD this doesn't apply), remove the 2 bolts that hold the Transmission Mount to the Crossmember (12mm or 14mm, it varies)
Slide the transmission back on the crossmember, away from the engine, I recommend running a ratchet strap across the frame to balance the transmission.
Remove the Pressure Plate from the Flywheel (Six 10mm bolts), Inspect the Pilot Bearing (if it needs replaced, you'll need to remove the Flywheel which is held on with six 18mm bolts, drive out the old bearing and drive in the new one, reinstall the flywheel, using Threadlocker on the bolts, torque the bolts to 100 ft lbs) Install the new clutch disc and Pressure Plate, with the centering tool inserted through the disc into the pilot bearing. Use thread locker on the pressure plate bolts and torque them to 20 ft lbs. Remove the centering/alignment tool after you've bolted it together
Remove old Throw Out bearing from input shaft on the transmission and slide the new one on. Slide the Transmission forward (make sure the input shaft slides into the pilot bearing, don't force the transmission into place or you could damage the clutch disc or break the input shaft) Torque the Bellhousing Bolts to 40 ft lbs (4 14mm bolts), Torque the 2 10mm bolts to 14 ft lbs, Install the Starter (torque bolts to 23 ft lbs), Reconnect Hydraulic Line to Slave Cylinder. Torque Transmission Mount Bolts to 30 ft lbs.
Reinstall Driveshafts, torque bolts on flange/yoke to 40 ft lbs. Fill Clutch Master Cylinder with DOT-3 Brake & Clutch Fluid, Open Bleeder Screw on Slave Cylinder and bleed the air out of the system, close bleeder screw.
Reconnect the wires to the Starter, Reconnect the battery.

Aug 24, 2011 | Mitsubishi Mighty Max Cars & Trucks

1 Answer

How to remove a transmission for a 2002 GMC Yukon


Removal & Installation 4L60E/4L65E To Remove:
  1. Remove or disconnect the following:
    • Transmission fluid
    • Transmission oil level indicator tube and seal from the transmission
    • Plug the oil level indicator tube opening in the transmission.
    • Remove or disconnect the following:
    • Shift cable end from the transmission shift lever ball stud
    • If equipped with a transfer case, remove the front propeller shaft.
    • Rear propeller shaft.
  2. Plug the transmission oil cooler line connectors in the transmission case.
  3. Remove or disconnect the following:
    • Starter motor.
    • Transfer case, if equipped.
  4. Support the transmission with a transmission jack.
  5. Remove the transmission mount nuts.
  6. Remove the transmission crossmember.
  7. Remove or disconnect the following:
    • Torque converter access plug 4L60E/4L65E removal 9308kg37.gif

    • Flywheel to torque converter bolts
    • The two bolts securing the transmission rear mount to the transmission
    • The transmission vent hose, fuel lines, and the wiring harness from the transmission
    • The stud and the bolt securing the transmission to the engine
    • The six studs and one bolt securing the transmission to the engine. Install tool J21366 onto the transmission bell housing to retain the torque converter. Pull the transmission straight back.
    • The transmission from the vehicle
  8. Flush the transmission oil cooler and cooling lines when you remove the transmission.
To Install:
  1. Install or connect the following:
    • Tool J21366 onto the transmission bell housing to retain the torque converter.
    • Support the transmission with a transmission jack.
  2. Raise the transmission into place and remove the tool from the transmission.
  3. Slide the transmission straight onto the locating pins while lining up the marks on the flywheel and the torque converter. The torque converter must be flush onto the flywheel and rotate freely by hand.
  4. Install or connect the following:
    • Six studs and one bolt securing the transmission to the engine. Tighten the studs and the bolt to 50 Nm (37 ft. lbs.).
    • Stud and bolt securing the transmission to the engine. Tighten the stud and the bolt to 50 Nm (37 ft. lbs.).
    • Flywheel to torque converter bolts. Tighten the stud and the bolt to 46 Nm (63 ft. lbs.).
    • Torque converter access plug.
    • Transmission vent hose, fuel lines, and the wiring harness to the transmission.
    • Two bolts securing the heat shield to the transmission. Tighten the bolt to 17 Nm (13 ft. lbs.).
    • Two bolts securing the transmission rear mount to the transmission. Tighten the bolts to 18 ft. lbs. (25 Nm).
    • Install the transmission crossmember. Tighten the nuts and bolts to 70 ft. lbs. (95 Nm).
  5. Remove the transmission jack from the transmission.
  6. Unplug the transmission oil cooler line connectors in the transmission case.
  7. Install or connect the following:
    • Starter
    • Transmission oil cooler lines to the transmission
    • If equipped with a transfer case, install the front propeller shaft.
    • The rear propeller shaft
    • The shift cable end to the transmission shift lever ball stud
  8. Unplug the oil level indicator tube opening in the transmission.
  9. Install the transmission oil level indicator tube and seal to the transmission.
  10. Tighten the oil pan bolts and fill the transmission with transmission fluid.
  11. Lower the vehicle.
4L80E/4L85E To Remove:
  1. Remove or disconnect the following:
    • Transmission fluid
    • Transmission oil level indicator tube and seal from the transmission
  2. Plug the oil level indicator tube opening in the transmission.
  3. Remove or disconnect the following:
    • Shift cable from the transmission shift lever ball stud
    • If 4WD vehicle, remove the propeller shaft.
    • If RWD vehicle, remove the propeller shaft.
    • The transmission oil cooler lines from the transmission
  4. Plug the transmission oil cooler line connectors in the transmission case.
  5. Remove or disconnect the following:
    • Starter motor
  6. Support the transmission with a transmission jack.
  7. Remove or disconnect the following:
    • The two bolts securing the heat shield to the transmission
    • The transmission vent hose, fuel lines, and the wiring harness from the transmission
    • One nut and one bolt securing the transmission brace to the engine bracket and transmission
    • The two bolts securing the torque converter cover to the engine
    • The four bolts securing the torque converter cover to the transmission
    • The six flywheel to torque converter bolts
    • The two bolts and nut securing the transmission rear mount to the transmission
    • The stud and the bolt on the right side securing the transmission to the engine
    • The remaining six studs and the one bolt securing the transmission to the engine
    • Tool J21366 onto the transmission bell housing to retain the torque converter
    4L80E/4L85E removal 9308kg36.gif

  8. Pull the transmission straight back. Remove the transmission from the vehicle.
  9. Flush the transmission oil cooler and cooling lines when you remove the transmission.
To Install:
  1. Install or connect the following:
    • Tool J21366 onto the transmission bell housing to retain the torque converter
  2. Support the transmission with a transmission jack.
  3. Raise the transmission into place and remove the tool from the transmission.
  4. Slide the transmission straight onto the locating pins while lining up the marks on the flywheel and the torque converter. The torque converter must be flush onto the flywheel and rotate freely by hand.
  5. Install or connect the following:
    • Six studs and one bolt securing the transmission to the engine. Tighten the studs and the bolt to 50 Nm (37 ft. lbs.).
    • The stud and bolt on the right side securing the transmission to the engine. Tighten the stud and the bolt to 50 Nm (37 ft. lbs.).
    • Six flywheel to torque converter bolts. Tighten the bolts to 60 Nm (44 ft. lbs.).
    • The two bolts securing the torque converter cover to the engine. Tighten the bolt to 50 Nm (37 ft. lbs.).
    • The four bolts securing the torque converter cover to the transmission. Tighten the stud and the bolt to 33 Nm (24 ft. lbs.).
    • The transmission vent hose, fuel lines, and the wiring harness to the transmission.
    • The two bolts securing the heat shield to the transmission. Tighten the bolt to 17 Nm (13 ft. lbs.).
    • The two bolts and nut securing the transmission rear mount to the transmission. Tighten the bolts and nut to 25 Nm (18 ft. lbs.).
    • The flywheel to torque converter bolts.
    • One nut and one bolt securing the transmission brace to the engine bracket and transmission. Tighten the bolts and nut to 50 Nm (37 ft. lbs.).
  6. Remove the transmission jack from the transmission.
  7. Install or connect the following:
    • Starter motor
  8. Unplug the transmission oil cooler line connectors in the transmission case.
  9. Connect the transmission oil cooler lines to the transmission.
  10. Install or connect the following:
    • The transfer case
    • The rear propeller shaft
    • The shift cable end to the transmission shift lever ball stud
  11. Unplug the oil level indicator tube opening in the transmission.
  12. Install the transmission oil level indicator tube and seal to the transmission.
  13. Tighten the oil pan bolts and fill the transmission with transmission fluid.
  14. Lower the vehicle.
prev.gif next.gif

Oct 12, 2010 | 2002 GMC Yukon XL

2 Answers

1997 z71 Transmission removal




  1. Disconnect the battery negative cable.
  2. Raise the vehicle. Support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  3. Disconnect the range selector cable from the transmission bracket and from the transmission range select lever. Refer to Shift Cable Replacement .
  4. Remove the rear propeller shaft. Refer to Rear Propeller Shaft in Propeller Shaft.
  5. Support the transmission with a transmission jack.
  6. Remove the transfer case if equipped. Refer to the appropriate Transfer Case Replacement in Transfer Case:
  7. Transfer Case Replacement (Selectable Four Wheel Drive) . • Transfer Case Replacement (Auto Four Wheel Drive ) . • Transfer Case Replacement (Manual Four Wheel Drive) .
    102329.gif
    tif.gif
  8. Gasoline Engine--Remove the following components:
  9. 7.1. Two bolts 7.2. Two washers 7.3. One nut 7.4. The transmission to engine brace
    102332.gif
    tif.gif
  10. Diesel Engine--Remove the following components:
  11. 8.1. Two bolts 8.2. Two washers 8.3. One nut 8.4. The transmission to engine brace
  12. Remove the transmission rear mount.
  13. Remove the frame crossmember.
  14. Remove the exhaust pipe from the exhaust manifolds. Remove the muffler assembly from the exhaust pipe, if required. Refer to Exhaust System.

  15. 102208.gif
    tif.gif
  16. For the 5.0L Gasoline Engine: Remove the six bolts securing the converter cover to the transmission.
  17. Remove the starter. Refer to Starter Replacement in Engine Electrical.
  18. For the 4.3L Gasoline Engine: Remove the dust plug at the end of the starter mounting port in order to gain access to the converter bolts.

  19. 102335.gif
    tif.gif
  20. For the Diesel Engine and 7.4L/5.7L Engines: Remove the four bolts securing the converter cover to the transmission.
  21. Mark the flywheel and the torque converter alignment.

  22. 102211.gif
    tif.gif
  23. Remove the bolts that attach the torque converter to the engine flywheel.

  24. 102339.gif
    tif.gif
  25. Remove the transmission vent hose.
  26. Disconnect the wiring harness connectors from the vehicle speed sensors and from the park neutral position switch.
  27. Remove all vehicle electrical harness wires, harness clips, tubes, and brackets that may interfere with the removal of the transmission.
  28. Remove the fluid fill tube and the fill tube seal from the transmission. Refer to Filler Tube Replacement .
  29. Plug the fluid fill tube opening in the transmission.
  30. Disconnect the transmission oil cooler pipes from the transmission. Refer to the oil cooler pipe quick connect fittings removal procedure in Oil Cooler Hose/Pipe Replacement .
  31. Plug the transmission oil cooler pipe connectors in the transmission case.
  32. Install the J 21366 in order to keep the torque converter from sliding off of the transmission turbine shaft.
  33. Support the engine with a suitable jack stand before removing the transmission from the engine.

  34. 102341.gif
    tif.gif
  35. 5.0L and 5.7L Gasoline Engine: Remove the studs and bolts securing the transmission to the engine.

  36. 102343.gif
    tif.gif
  37. 4.3L Gasoline Engine: Remove the studs and bolts securing the transmission to the engine.
  38. Pull the transmission straight back from the engine.
  39. Lower the transmission using the transmission jack.
  40. Flush the transmission oil cooler and the pipes whenever you remove the transmission for overhaul, or replacement of the torque converter, the pump, or the transmission case. Refer to Transmission Fluid Cooler Flushing .
  41. Clean the transmission case using a solvent dampened cloth. Do not allow solvent to enter the transmission.
  42. Air dry the transmission.
  43. Clean all hardware and the flywheel cover using solvent. Air dry all the parts.
  44. Inspect all the components for wear and damage.
  45. Inspect all the seals and the fittings for signs of wear.
  46. Inspect the torque converter for stripped or broken weld nuts.
  47. Inspect the transmission case for cracks.

Jul 06, 2009 | 1997 Chevrolet K1500

1 Answer

Transmission quit moving no noise, nothing grinding etc..


If it doesn't move forward or backward, then the pump or torque converter are likely bad. First put it in drive with the rear wheels up. Pull out the speed sensor in the overdrive unit( rear housing on the trans) and look in the hole to see if the output shaft is turning. This will tell you if this is a trans problem or a transfer case problem. If it is turning but the rear drive shaft isn't, inspect the transfer case. If the output shaft isn't turning, hook up a pressure gauge to the transmission and check for line pressure. If line pressure is low, replace the pump. If line pressure is good, replace the torque converter.

Feb 27, 2009 | 1994 Jeep Grand Cherokee

2 Answers

How Does Quadra Drive Work?


Under normal driving conditions, the system operates conventionally, and the majority of available torque is applied to the rear wheels. However, when front-to-rear wheel speed variations exist, the progressive differential transfers torque to the axle with the better traction, thus minimizing wheel spin and maximizing control.
The key to this design is a progressive coupling Progressive Coupling , which is supplied with pressurized oil by a gerotor style pump. The pump rotor and case are driven by the front and rear driveshafts respectively, and deliver pressurized oil flow to the coupling in proportion to their speed difference. The progressive coupling contains a multi-disc clutch pack that is alternately splined to the front and rear driveshafts, and controls torque variation between the front and rear driveshafts as dictated by the pump.
A set of orifices and valves control the speed-differential starting point and rate of torque transfer rise in the clutch. This allows the system to disregard the normal speed differences between axles that result from variations in front-to-rear loading and typical cornering.
Transfer case operating ranges are selected with a floor mounted shift lever. The shift lever is connected to the transfer case range lever by an adjustable cable. Range positions are marked on the shifter bezel plate

Jan 08, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Removing tranny


Ok..
This is the prosses to remove and install your Transmission.

1---Disconnect negative Battery cable. Remove Air cleaner. Disconnect shift cable from Transmission. Raise and support Vehicle. Drain Transmission fluid. Disconnect shift Linkage. Mark rear drive shaft for installation reference and fremove from vehicle. Mark front drive shaft and Remove from transfer case.
Warning.. ALWAYS relieve fuel pressure before disconnecting any fuel injection related component DO NOT allow fuel to contact electrical components.

2-- Relieve fuel pressure, and remove fuel lines from the Bracket support at catalistyc converter
And remove the bracket. support transmission with transmission jack or any compatible.
Remove transmission crossmember.
NOTE .. DO NOT stretch or damage any cables, wires or other components when lowering transmission.

3-- Lower transmission far enough to provide clearence for other components. remove dipstick tube and seal. cover opening in transmission. remove speedometer harness. remove electrical connectors from transmission. remove cooler lines, and cap all openings. remove starter motor.

4-- Remove transfer case shifter and move it aside, Remove transmission support braces. Note braces locatoin for installation. Remove converter housing cover. Mark flexplate( flywhell) and Torque converter for alingment during installation, Remove flywheel to torque converter BOLTS.

Remove transmission to Engine BOLTS. note location of any brackets or clips and move them aside. Slide transmission straight back, off locating pins, remove transmission from vehicle.

6-- To install, reverse removal procedure. Torque converter must be against flywheel and rotate
FREELY by HAND, ensure all reference mark aling. and tighten all BOLTS..

NOTE. In some cases is nessesary remove the Transfer case before the transmission.
The transfer case is attached at the transmission with six Bolt .....


OK... I hope this help on your question.
Thank yuo for use fixya...

Oct 01, 2008 | 1996 Chevrolet Suburban

Not finding what you are looking for?
1998 Jeep Grand Cherokee Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...