Question about 1995 Buick Riviera

1 Answer

Cant change rear brakes to the 1995 rear brakes of a buick riveira? It had one bolt. How do I get it off?

Posted by on

  • Anonymous May 11, 2010

    Need more info. Have you got any experience with brakes??



1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I think it takes a special tool, i i know it does for the calipers

Posted on May 06, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

1996 buick regal custom has no coil springs on rear how do i change the shocks

26083109-sgzmnh3u5bmrsfnwqwi1so0h-1-0.gif Removal:
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle with jackstands.
  3. Remove the rear wheel and tire assembly.
  4. Scribe the strut-to-knuckle for proper installation.
  5. If equipped, remove the auxiliary spring, as outlined in this section.
  6. Remove the jack pad.
  7. Install rear leaf spring compressor tool J-35778, or equivalent. Refer to the Transverse Spring Assembly procedures in this section for installation details.
  8. Fully compress the spring, but do NOT remove the retention plates or the spring.
  9. Unfasten the two strut-to-body bolts.
  10. Remove the brake hose bracket from the strut.
  11. Remove the strut and auxiliary spring upper bracket from the knuckle.
To install:
  1. Position the strut to the body and knuckle bracket.
  2. Install the strut-to-body bolts and tighten to 34 ft. lbs. (46 Nm).
  3. Install the strut to the knuckle, aligning the scribe marks and tighten the bolts to 133 ft. lbs. (180 Nm) for 1988-94 vehicles. For 1995-96 vehicles, tighten the bolts to 122 ft. lbs. (165 Nm).
  4. Install the brake hose bracket.
  5. Remove the spring compressing tool.
  6. Install the jack pad and tighten the retaining bolts to 18 ft. lbs. (25 Nm).
  7. If equipped, install the auxiliary spring.
  8. Install the wheel and tire assembly and install the lug nuts finger-tighten
  9. Carefully lower the vehicle, then tighten the lug nuts to 100 ft. lbs. (136 Nm).
  10. Connect the negative battery cable.

Feb 05, 2016 | Buick Cars & Trucks

1 Answer

Only one rear brake working on 1995 lesabre

Are the pads and cylinder ok? If not, get brakes done.

Mar 03, 2014 | Buick LeSabre Cars & Trucks

2 Answers

1995 buick lesabre. brakes are gone! fluid leaking from left rear brake.

If they are drum brakes then it is most likely the wheel cylinder. these are not expensive but you will need to replace the rear brake shoes and clean all the parts with brake clean. I recomend replacing the other cylinder while your at it.

Nov 22, 2010 | 1995 Buick Regal

1 Answer

What are the torque settings for mounting an automobile air conditioner compressor on a 1995 buick century with a 3.1 engine

Hello! Install bolts...Tighten front bolts to 37' #'s...Rear bolts to 22' #'s...Attach compressor hose and tighten bolts to 24' #'s........


Aug 06, 2010 | 1995 Buick Century

3 Answers

Rear brake lights don't work , but center brake light does.

brake lights won't work, but the center does ??? u need to change your turn signal switch which is in the steering wheel. i changed mine and it worked great .....

hope that helps

Apr 22, 2010 | 1995 Buick Regal

1 Answer

How to remove serpintine belts from a1998 buick riveira

Take off the top engine mount by the belts. Then there's a spacer below the you need to get out.. it's a big operation all together. But do not worry about taking apart the black arm mounted on the engine. That's what the spacer is for. So just jack up your engine enough so it doesn't fall when you take the mount off. You will also need to take the engine up & down to work the bolts out. Good Luck!

Jan 18, 2010 | 1998 Buick Riviera

1 Answer

How do i change a hub bearing on a 1995 buick riviera

Remove everything behind the wheel, brakes and rotor and you should see the hub with holes thru it and see the bolts that remove it. Is it front or rear bearings?

Oct 21, 2009 | 1995 Buick Riviera

1 Answer

Changing rear brake pads on 2002 buick lesabre

Your correct, does hinge on top bolt and then is ussually stiff pulling from pin, but it will move

Jun 30, 2009 | 2005 Buick LeSabre

1 Answer

Trying to replace brake cylinder on a 1995 buick skylark rears

On some of the gm cars you had to remove or at least unbolt the hub assy. to clear the wheel cyl. some are bolted from the back side there should be 4 bolts that you have to lossen up and pull the hub outward to make clearance.

Mar 28, 2009 | 1995 Buick Skylark

Not finding what you are looking for?
1995 Buick Riviera Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides