Question about 2000 Chevrolet Silverado 1500

1 Answer

Which way does the soleinod cover go back on the starter

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

Looking at the solenoid front, where the wires go, it goes from about 9 o'clock to 12 o'clock.

Posted on May 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix starter bendix gmc safari


Wow i did not know they sell starter drives any more. With starter off engine remove the two bolts that hold front bushing on the motor then remove the single bolt from solenoid to motor barrel remove barrel then armature can come out Now you will see a ring spacer that is lifted one side it faces the metal ring cover remove and tap cover back remove wire ring replace starter drive put ring on with pliers squeeze cover over wire and install last ring spacer and reassemble starter.

Nov 09, 2013 | GMC Cars & Trucks

1 Answer

How do i connect my starter to the battery


REMOVAL & INSTALLATION 2.2L (VIN 4) Engine Fig. 1: Removal and installation of the starter — 2.2L engine shown 87952039.gif
Fig. 2: Remove the starter electrical connections from the back of the starter 91142p05.jpg
Fig. 3: Remove the three bell-housing cover retaining bolts and . . . 91142p06.jpg
Fig. 4: . . . remove the bell-housing cover 91142p07.jpg
Fig. 5: Remove the starter support brace-to-engine bolt 91142p08.jpg
Fig. 6: The starter is retained by two bolts 91142p09.jpg
Fig. 7: Remove the bolts and . . . 91142p10.jpg
Fig. 8: . . . remove the starter from the engine 91142p11.jpg
Fig. 9: Note that the starter bolts are two different lengths, the longer one goes on the inside 91142p12.jpg
  1. Disconnect the negative battery cable at the battery.
  2. Raise and safely support the vehicle.
  3. Remove the electrical connections from the back of the starter.
  4. Remove the bell-housing cover.
  5. Remove the starter support bracket bolt from the engine block.
  6. Unfasten the starter motor-to-engine bolts, then carefully lower the starter.
  7. Remove the nuts/bolts that hold the starter support bracket to the starter. To install:
  8. Transfer the starter support bracket to the new starter if the starter is being replaced.
  9. Raise the starter into position and secure the starter using the starter motor-to-engine bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
  10. Install the starter support bracket-to-engine bolt to 24 ft. lbs. (32 Nm).
  11. Install the bell-housing cover.
  12. Install the starter electrical connections on the back of the starter. Tighten the "S'' terminal to 22 inch lbs. (2.5 Nm) and the battery terminal to 106 inch lbs. (12 Nm).
  13. Carefully lower the vehicle, then connect the negative battery cable.
2.3L (VIN D) and 2.4L (VIN T) Engines Fig. 10: When installing the starter, tighten the mounting bolts to 66 ft. lbs. (90 Nm) on the 2.3L and 2.4L engines 87952040.gif
  1. Disconnect the negative battery cable at the battery.
  2. Detach the air inlet duct from the throttle body.
  3. Remove the top starter bolt.
  4. Raise and safely support the vehicle.
  5. Remove the lower starter retaining bolt.
  6. If necessary, position the engine wiring harness aside.
  7. Position the starter to enable access to the solenoid wiring, then detach the wiring.
  8. Remove the starter from the vehicle. To install:
  9. Raise the starter to the vehicle, then attach the wiring.
  10. Position the starter, then secure using the lower starter bolt. Tighten to 66 ft. lbs. (90 Nm)
  11. If moved, reposition the engine wiring harness.
  12. Carefully lower the vehicle.
  13. Install the top starter bolt, then tighten to 66 ft. lbs. (90 Nm).
  14. Fasten the air inlet duct to the throttle body.
  15. Connect the negative battery cable.
prev.gif next.gif

Aug 19, 2010 | 1996 Chevrolet Cavalier

2 Answers

How to remove starter


Removal & Installation - Starter
  1. Before servicing the vehicle.
  2. Remove or disconnect the following:
    Negative battery cable Radiator air baffle assembly
    Electrical connections Torque converter cover Starter
To install:
  1. Install or connect the following:
    Starter. Torque the bolts to 35 ft. lbs. (47 Nm). Torque converter cover Solenoid -BAT- terminal. Torque the nut to 89 inch lbs. (10 Nm). Solenoid -S- terminal. Torque the nut to 27 inch lbs. (3 Nm). Radiator air baffle assembly Negative battery cable
  2. Perform a charging system test and verify the starter is operating properly
8e0154d.jpg

Fig. Showing the starter motor location and electrical connections
  1. Before servicing the vehicle.
  2. Remove or disconnect the following:
    Negative battery cable Radiator air baffle, for clearance if necessary Flywheel inspection cover bolts Flywheel inspection cover Electrical connections from the starter motor Starter motor mounting bolts Starter motor
To install:
  1. Install or connect the following:
    NOTE Before installing the starter motor to the engine, tighten the nut next to the cap on the solenoid BAT terminal. If this terminal is not tight in the solenoid cap, the cap may be damaged during installation of electrical connections and cause the starter motor to fail later.

    Starter motor Starter motor mounting bolts and tighten the bolts to 30 ft. lbs. (40 Nm) Electrical connection to the battery terminal on the solenoid and tighten the battery terminal nut to 13 ft. lbs. (17 Nm) Electrical connections to the S terminal on the solenoid and tighten solenoid S terminal nut to 27 inch lbs. (3 Nm) Flywheel inspection cover Flywheel inspection cover bolts Radiator air baffle, if removed
  2. Connect the negative battery cable

Hope helps, remember rated this.

Aug 12, 2010 | 2001 Pontiac Montana

1 Answer

How to replace the starter?


Before we get started, are you positive it is the starter ?
You could have dead battery, loose or corroded cables, bad relay. If your sure then,
Here are the steps :
-Remove negative(black)battery cable.
-Remove plastic cover from transmission that covers the starter /ring gear.
-Unbolt starter from engine, and bracket.
-Slowly lower starter, and remove cables, and wires, but MAKE SURE you mark then so you know how they go back on !
-Pull out starter.
-Install in reverse order.

Feb 12, 2010 | 1999 Dodge Caravan

1 Answer

My tracker is a automatic and it will not go past 25 mph. Someone said they heard the shift soleinod needs ajusted.


Check the crankshaft pulley that drives the "fan" belt. If it feels loose on the crankshaft, have a mechanic check it. This is a common problem and will cause thw engine to lose power because it affects engine timing.
Cspick

Jun 16, 2009 | 1995 Geo Tracker

1 Answer

Reinstall of Starter 1998 2.4L Chev Cavalier


moz-screenshot-4.jpg
  1. Disconnect the negative battery cable at the battery.
  2. Raise and safely support the vehicle.
  3. Remove the electrical connections from the back of the starter.
  4. Remove the bell-housing cover.
  5. Remove the starter support bracket bolt from the engine block.
  6. Unfasten the starter motor-to-engine bolts, then carefully lower the starter.
  7. Remove the nuts/bolts that hold the starter support bracket to the starter.

To install:
  1. Transfer the starter support bracket to the new starter if the starter is being replaced.
  2. Raise the starter into position and secure the starter using the starter motor-to-engine bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
  3. Install the starter support bracket-to-engine bolt to 24 ft. lbs. (32 Nm).
  4. Install the bell-housing cover.
  5. Install the starter electrical connections on the back of the starter. Tighten the S terminal to 22 inch lbs. (2.5 Nm) and the battery terminal to 106 inch lbs. (12 Nm).
  6. Carefully lower the vehicle, then connect the negative battery cable.

2.3L (VIN D) and 2.4L (VIN T) Engines
See Figure 10


0900c1528003cb99.jpg

Apr 08, 2009 | 1998 Chevrolet Cavalier

1 Answer

STARTER


It should be on the passenger side of the oil pan, 2 bolts hold it to the cylinder block, should have some wires going to the soleinoid, disconnect the negative side of the battery first, most the time it's just the soleinod that goes bad...should have 2 bolts on the sides of it { the soleinod } and 1 on the lower middle of it with a spring inside, get the bolts out and twist the soleinod until the lip comes around out of the groove of the starter, should pop right off.

Feb 25, 2009 | 1992 Chevrolet S-10

1 Answer

7.3 oil leak above starter head area


pull insp. cover sounds like rear main seal

Dec 14, 2008 | 1999 Ford Escort

1 Answer

Truck will not start


yes it does,new vehicles have in bord self power cuter for security .but please chek for 100 to 80 amp fuses and battery attachement connections ,starter connections and all the wires from batterie to soleinod and from solenoid to batterie if not , then take you vehicle to the close dealer for recalibratoin (flasch) of you security system .....nicolas

Nov 15, 2008 | 2008 GMC Sierra 2500HD 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...