Question about 2004 Mitsubishi Outlander

Open Question

Replace fuel filler neck assembly,leaking vent, purge solenoid and faulty evap. hose

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: mitsubishi 98 faulty fuel cap, leaking vent or

do you know how to open a fuel cap on shogun 3.2 ddi as it wont open

Posted on Oct 08, 2010

Ad
  • 1 Answer

SOURCE: mitsubishi 98 faulty fuel cap, leaking vent or

Mitsubishi 2006 faulty fuel cap, leaking vent or purge solenoid, EVAP hose faulty or leak on fuel tank.... replace the fuel cap and a week later the light was back on...the code is P0442..what to do next

Posted on Oct 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

045500 error code on a Chev silverado 1500 2009 5.3 lt what does it say


DTC P0455
  • Evaporative Emission (EVAP) System Large Leak Detected

Jul 23, 2014 | 2009 Chevrolet Silverado 1500

1 Answer

P0446 ford escort 98


This Pinpoint Test is intended to diagnose the following:
  • Canister vent (CV) solenoid (9F945) (electrical concern only)
  • Fuel filler cap (9030)
  • Fuel tank pressure (FTP) sensor (9C052)
  • EVAP canister tube (fuel tank to EVAP canister)(9A228)
  • Fuel canister purge outlet tube (EVAP canister to EVAP canister purge valve) (9D661)
  • EVAP return tube (EVAP canister purge valve to intake manifold) (9G271)
  • EVAP canister purge valve (9C915)
  • Vacuum source line (input port vacuum to intake manifold)
  • Harness circuits: CV, FLI, FTP, EVAP Canister Purge Valve, SIG RTN, vehicle power (VPWR), reference voltage (VREF) and power ground (PWR GND)
  • Powertrain control module (PCM) (12A650)
This Pinpoint Test is used as an assistance in diagnosing the following EVAP components:
  • EVAP canister and bracket assembly (9E857)
    • EVAP canister sleeve assembly (fitting)(9D925)
    • Canister vent (CV) solenoid - hose assembly (9F976 or 9K318)
    • EVAP canister (9D653)
    • Canister vent (CV) solenoid (9F945)(mechanical concern only)
  • Fill limit valve assembly (9A086)
  • Fuel filler pipe flapper valve (9B085)
  • Fuel filler pipe check valve (9189), assembly (9285)
  • Fuel tank filler pipe (9034)
  • Fuel tank assembly (with fuel vapor vent valve) (9K007)
  • Fuel tank assembly (without fuel vapor vent valve) (9002)
  • Fuel vapor control valve (9B190)
  • Fuel vapor vent valve (9B593)
  • Liquid/vapor fuel discriminator (9G332)
  • On-board refueling vapor recovery (ORVR) T - connector assembly (9S314)
Description For additional information on the Evaporative Emission (EVAP) System, refer to Section 1A .
For additional information on the Evaporative Emission System Monitor, refer to Section 1A .
Pinpoint Test Schematics Escort/Tracer (2V)
aa3060b.gif

May 28, 2011 | 1998 Ford Escort

1 Answer

On my 2001 rodeo the check engine lite came on and the only code that came up is po440, can you tell me what this is


This alarm concerns the function of the EVAP SYSTEM. This system monitors vacuum correctness. If a sufficient vacuum level cannot be achieved, a large leak or a faulty EVAP canister purge solenoid is indicated. It can be caused for the following reasons:
1) Disconnected or faulty fuel tank pressure sensor
2) Missing or faulty fuel cap
3) Disconnected, damaged, pinched, or blocked EVAP purge line.
4) Disconnected or damaged EVAP vent hose.
5) Disconnected, damaged, pinched, or blocked fuel tank vapor line.
6) Disconnected or faulty EVAP canister purge solenoid.
7) Disconnected or faulty EVAP canister vent solenoid.
8) Damaged EVAP canister.
9) Leaking fuel sender O-ring.
10) Leaking fuel tank or fuel filler neck.

Apr 13, 2011 | 2001 Isuzu Rodeo

1 Answer

I recently purchased this 1999 Chevy Blazer and it wont pass inspection because the OBD2 Diagnostic trouble code states it's problem is, code P0440-Evaporative Emission System. The guy said it looks like...


The evaporative leak detection diagnostic strategy is based on applying a vacuum to the EVAP system and monitoring the vacuum decay rate. The VCM monitors the vacuum level via the fuel tank pressure sensor input. At an appropriate time, the EVAP purge solenoid and the EVAP vent solenoid turn ON, allowing the engine vacuum to draw a small vacuum on the entire evaporative emission system. If a sufficient vacuum level cannot be achieved, a large leak or an EVAP system malfunction is indicated.

The following conditions can cause this problem:
* A disconnected or malfunctioning fuel tank pressure sensor
* A missing, malfunctioning, improperly installed, or loose fuel cap
* A disconnected, damaged, pinched, or blocked EVAP purge line
* A disconnected or damaged EVAP vent hose
* A disconnected, damaged, pinched, or blocked fuel tank vapor line
* A disconnected or malfunctioning EVAP purge solenoid
* A disconnected or malfunctioning EVAP vent solenoid
* An open ignition feed circuit to the EVAP vent or purge solenoid
* A damaged EVAP canister
* A leaking fuel sender assembly O-ring
* A leaking fuel tank or fuel filler neck

Any of the above conditions can set a DTC P0440.

Mar 08, 2011 | 1999 Chevrolet Blazer

2 Answers

Codigo p1440


EVAP System Vent Circuit Malfunction

This diagnosis detects leaks in the Evaporative Emission (EVAP) purge line using of vapor pressure in the fuel tank. The EVAP canister vent control valve is closed to shut the EVAP purge line. The vacuum cut valve bypass valve will then be opened to clear the line between the fuel tank and the EVAP canister purge volume control solenoid valve. The EVAP control system pressure sensor can now monitor the pressure inside the fuel tank. If pressure increases, the Engine Control Module (ECM) will check for leaks in the line between the vacuum cut valve and EVAP canister purge volume control solenoid valve.

Possible causes
- Incorrect fuel tank vacuum relief valve
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- Leak is in line between intake manifold and EVAP canister purge volume control solenoid valve
- Foreign matter caught in EVAP canister vent control valve
- EVAP canister or fuel tank leaks
- EVAP purge line (pipe and rubber tube) leaks
- EVAP purge line rubber tube bent
- Blocked or bent rubber tube to EVAP control system pressure sensor
- Loose or disconnected rubber tube
- EVAP canister vent control valve and the circuit
- O-ring of EVAP canister vent control valve is missing or damaged
- EVAP canister is saturated with water
- EVAP control system pressure sensor
- Absolute pressure sensor

Possible solution
- Loose fuel filler cap
- Leaking fuel filler cap


Hope helps (remember to rate this answer).

Jan 05, 2011 | 2000 Hyundai Sonata

1 Answer

Loolking for code P0445 what does this mean


P0445- EVAP purge control circuit fault!! Check your gas cap, this will cause insufficient vacuum activating the SES indicator. Check the following

a) Absent or tampered fuel cap.

b) De-linked or faulty fuel tank pressure sensor.

c) De-linked, damaged, pinched, or blocked EVAP purge line.

d) De-linked or erroneous EVAP canister purge valve.

e) De-linked or incorrect EVAP vent solenoid.

f) Open ignition feed circuit to the EVAP vent or purge solenoid.

g) Tampered EVAP canister.

h) Leaking fuel sensor assembly O-ring.

i) Leaking fuel tank or fuel filler beck

Sep 29, 2010 | 2008 GMC Sierra 1500

1 Answer

Obd-2 code p1455


DTC P1455 - Substantial Leak or Blockage in Evaporative Emission Control System

The PCM monitors the complete EVAP control system for no purge flow, the presence of a large fuel vapor leak or multiple small fuel vapor leaks. The system failure occurs when no purge flow (attributed to fuel vapor blockages or restrictions), a large fuel vapor leak or multiple fuel vapor leaks are detected by the EVAP running loss monitor test with the engine running (but not at idle).

Check this possible causes:
After-market EVAP hardware (such as fuel filler cap) non-conforming to required specifications
Disconnected or cracked fuel EVAP canister tube, EVAP canister purge outlet tube or EVAP return tube
EVAP canister purge valve stuck closed
Damaged EVAP canister
Damaged or missing fuel filler cap
Insufficient fuel filler cap installation
Loose fuel vapor hose/tube connections to EVAP system components
Blockages or restrictions in fuel vapor hoses/tubes (items also listed under disconnections or cracks)
Fuel vapor control valve tube assembly or fuel vapor vent valve assembly blocked
Canister vent (CV) solenoid stuck open
Mechanically inoperative fuel tank pressure (FTP) sensor


Check for audible vacuum noise or significant fuel odor in the engine compartment or near the EVAP canister and fuel tank

Tell us news.

Jul 19, 2010 | 1996 Ford Explorer

1 Answer

P044o code popped up on my Blazer. there is a fuel smell coming from the back and everytime that i fuel up and it stops pumping it flows over from the tank underneath the truck. talked to a guy at AutoZone...


The evaporative leak detection diagnostic strategy is based on applying a vacuum to the EVAP system and monitoring the vacuum decay rate. The VCM monitors the vacuum level via the fuel tank pressure sensor input. At an appropriate time, the EVAP purge solenoid and the EVAP vent solenoid turn ON, allowing the engine vacuum to draw a small vacuum on the entire evaporative emission system. If a sufficient vacuum level cannot be achieved, a large leak or an EVAP system malfunction is indicated. The following conditions can cause this problem:
A disconnected or malfunctioning fuel tank pressure sensor.
A missing, malfunctioning, improperly installed, or loose fuel cap.
A disconnected, damaged, pinched, or blocked EVAP purge line.
A disconnected or damaged EVAP vent hose.
A disconnected, damaged, pinched, or blocked fuel tank vapor line.
A disconnected or malfunctioning EVAP purge solenoid.
A disconnected or malfunctioning EVAP vent solenoid.
An open ignition feed circuit to the EVAP vent or purge solenoid.
A damaged EVAP canister.
A leaking fuel sender assembly O-ring.
A leaking fuel tank or fuel filler neck.
Any of the above conditions can set a DTC P0440.

Your may have to drop the tank and check the vent valve, see if it's broke off at the vacuum line fitting since you mentioned that gas las leaking from the tank. 
When checking the vent/purge solenoid, depends on whether you have a 2dr or a 4dr. I can't remember the exact location of the 2dr vent/purge solenoid, but on a 4dr, just drop the spare tire if you have it underneath and it'll be in the middle of the cross member directly behind the rear axle. It'll have one large vacuum line and an electrical connector. 
You can also see the gas filler tube to the rear of the gas tank, check for any damages where the gas may be coming out of.
Good luck and hope this saves you some money, I believe most dealer will charge close to $400.00 to drop the gas tank and do this job.

May 09, 2009 | Chevrolet Blazer Cars & Trucks

1 Answer

Check engine light is on for emission evaporator failure-large


P0455 - EVAP Control System Leak Detected (No Purge Flow or Large Leak) The PCM monitors the complete EVAP control system for no purge flow, the presence of a large fuel vapor leak or multiple small fuel vapor leaks. The system failure occurs when no purge flow (attributed to fuel vapor blockages or restrictions), a large fuel vapor leak or multiple fuel vapor leaks are detected by the EVAP running loss monitor test with the engine running (but not at idle).
  • After-market EVAP hardware (such as fuel filler cap) non-conforming to required specifications
  • Disconnected or cracked fuel EVAP canister tube, EVAP canister purge outlet tube or EVAP return tube
  • EVAP canister purge valve stuck closed
  • Damaged EVAP canister
  • Damaged or missing fuel filler cap
  • Insufficient fuel filler cap installation
  • Loose fuel vapor hose/tube connections to EVAP system components
  • Blockages or restrictions in fuel vapor hoses/tubes (items also listed under disconnections or cracks)
  • Fuel vapor control valve tube assembly or fuel vapor vent valve assembly blocked
  • Canister vent (CV) solenoid stuck open
  • Mechanically inoperative fuel tank pressure (FTP) sensor
Check for audible vacuum noise or significant fuel odor in the engine compartment or near the EVAP canister and fuel tank. ----------------------------------------------------------------------------- HX43 DTC P0457: CHECK FOR MISSING OR LEAKING FUEL FILLER CAP
  • Check for missing fuel filler cap.
  • Check for loose fuel filler cap.
  • Check for possible cross-thread fuel filler cap condition.
Is a fault present concerning the proper installation of the fuel filler cap? Yes No REPLACE cross-threaded or damaged fuel filler cap. RECONNECT and TIGHTEN the fuel filler cap only one eighth turn so that the cap initially clicks by sound or touch. CLEAR Continuous Memory DTCs. COMPLETE an Evaporative Emission Running Loss Monitor Repair Verification Drive Cycle (refer to Section 2 , Drive Cycles). RERUN Quick Test . If DTC P0455 or P0457 is present, Go to HX44 . CLEAR Continuous Memory DTCs. COMPLETE an Evaporative Emission Running Loss Monitor Repair Verification Drive Cycle (refer to Section 2 , Drive Cycles). RERUN Quick Test .

For DTC P0455 still present: Go to HX44 .

Otherwise, INFORM the vehicle owner that it is important and necessary to immediately install the fuel filler cap after every refueling event. HX44 DTC P0455: VISUAL INSPECTION FOR SUBSTANTIAL EVAPORATIVE EMISSION SYSTEM LEAKS
  • Check for missing fuel filler cap. If the cap is loose DO NOT DISTURB EVAP system.
  • Verify that both the input port vacuum hose and EVAP return tube are attached to the EVAP canister purge valve. Note: If the EVAP canister-CV solenoid assembly is not accessible during this pinpoint test step, GO to Evaporative Emissions, Section 303-13 in the Workshop Manual for removal and installation instructions.
  • Verify that the CV solenoid is properly seated on the EVAP canister (if possible).
  • Visually inspect for disconnected or cracked fuel vapor hoses/tubes between the intake manifold, the EVAP canister purge valve, the EVAP canister, the fuel vapor vent valve assembly and if applicable the fuel vapor control valve tube assembly.
  • Check for damage to the fuel filler pipe and the fuel tank.
Is a fault indicated? Yes No CONNECT or REPLACE fuel vapor hoses/tubes as required. REPLACE damaged EVAP system components (fuel filler pipe, fuel vapor vent valve assembly, fuel vapor control valve tube assembly, EVAP canister purge valve, FTP sensor and EVAP canister-CV solenoid assembly) as necessary. REFER to Evaporative Emissions, Section 303-13 in the Workshop Manual for removal and installation instructions. GO to HX45 . GO to HX45 . HX45 DTC P1443 and P0455: CHECK FOR EVAPORATIVE EMISSION SYSTEM LEAKS
    Note: When checking for leaks or blockages in the EVAP system, energize (close) the canister vent (CV) solenoid through the scan tool for a maximum of nine minutes per pinpoint test step. Then de-energize the CV solenoid prior to performing the subsequent pinpoint test step. This is done to assure proper closing of the solenoid.
  • Disconnect and plug the EVAP return tube (EVAP canister purge valve to intake manifold) at the intake manifold vacuum source.
  • Connect scan tool.
  • Key on, engine off.
  • Access VPWR PID. If the voltage is not 12 volts or greater, GO to HX61 .
  • Locate evaporative test port [marked EVAPORATIVE SERVICE PORT DO NOT USE UNREGULATED PRESSURE ABOVE 6.89 kPa (1 PSI)] near EVAP canister purge valve or EVAP canister.
  • If vehicle is not equipped with the evaporative test port, GO to HX50 .
  • Install the Rotunda Evaporative Emission System Leak Tester 310-F007 (134-00056) or equivalent at the evaporative test port.
  • Close CV solenoid by accessing Output Test Mode on the scan tool.
  • Select ALL OFF mode and push START button.
  • Regulate the nitrogen or argon gas pressure on the tester to 3.48 kPa (14 in-H 2 O).
  • Follow the instructions that come with the EVAP System Leak Tester and pressurize the EVAP system.
  • Perform the EVAP system leak test.
Does the pressure on the EVAP system stay above 1.99 kPa (8 in-H 2 O) and pass the leak test? Yes No GO to HX46 . REMOVE the EVAP System Leak Tester from the evaporative test port and REINSTALL the test port cap. GO to HX50 .

Apr 15, 2009 | 1999 Lincoln Town Car

1 Answer

My taurus failed due to code p0442 ecap emiss ctl sys leak detected (small leak)


    Continuous Memory Diagnostic Trouble Code (DTC) P0442 indicates that a fuel vapor leak has been detected [as small as 0.10 cm (0.04 inch)] in the Evaporative Emission (EVAP) system.
    Note: Prior to performing the following diagnosis inspect the Canister Vent Solenoid (CV) for contamination. A situation may exist where contamination holds open the Canister Vent (CV) solenoid enough to set DTC P0442 and also plugs the port to atmosphere enough to keep system from being vented quickly.
    • After market parts and accessories nonconforming to the EVAP system specifications.
    • Damaged, cross threaded or loosely installed fuel filler cap.
    • Small holes or cuts in fuel vapor hoses/tubes (EVAP canister tube, EVAP canister outlet tube or EVAP return tube) in the EVAP system.
    • Loose fuel vapor hose/tube connections to EVAP system components.
    • EVAP system component [EVAP canister purge valve, fuel tank pressure (FTP) sensor, canister vent (CV) solenoid, fuel vapor control valve tube assembly or fuel vapor vent valve assembly] seals leaking.
    • CV solenoid partially open when commanded closed.
    • EVAP canister leaking.
  • Check for presence of fuel filler cap.
  • Verify that the CV solenoid is properly seated on the EVAP canister (if possible).
  • Visually inspect for cut or loose connections to fuel vapor hoses/tubes in following locations:
    • EVAP canister to EVAP canister purge valve.
    • EVAP canister to fuel vapor vent valve assembly.
    • fuel vapor control valve tube assembly to fuel tank (if applicable).

Jun 26, 2008 | 1997 Ford Taurus

Not finding what you are looking for?
2004 Mitsubishi Outlander Logo

Related Topics:

246 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...