Question about 1994 GMC Jimmy

1 Answer

Spark to plugs , not strong enough - 1994 GMC Jimmy

Posted by on

  • yadayada
    yadayada May 11, 2010

    no such thing.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

I would check the coil, coil wire and spark plug wires. A local parts store should have the Ohms reading for the coil, coil wire and plug wires.

Posted on May 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What id the problem with lawnmower


pull flywheel and replace shear key

Jul 07, 2015 | Cars & Trucks

1 Answer

Renault laguna cranking not starting fuel is going spark is there


compression may be weak--residual fuel pressure cud be low--spark mite not be strong enough-inspect plug wires-coil-ignition module-distributer cap--timing belt may have slipped a notch--is battery at 12.6volts and cables tite--

Jan 05, 2015 | Renault Cars & Trucks

1 Answer

Why will my 2002 suburban crank but not start after installing a starter


assuming the starter is installed properly, it could be a variety of things. if the battery is not strong enough to fully start the truck. could check the condition of spark plugs and spark plug wiring.

Jun 20, 2014 | 2003 Chevrolet Suburban 1500

1 Answer

Spark on coil but no spark on plugs


check to see if spark is strong enough if it is replace the spark plug wires then recheck

Jan 12, 2013 | Volkswagen Golf Cars & Trucks

1 Answer

I have a 96 ford explorer v6 with a pushrod motor and after we replaced the pushrods, the head gaskets, the valve cover gaskets and the fuses, the car will not idle. what could be the problem?


Have you adjusted the pushrods properly? Pushrods generally need to be adjusted after installation.

Not sure how to do this on this model, although I own a 94 Ford Explorer with the V6 4.0 Liter motor.

Basically, when a gas engine doesn't run, you check 4 things, and narrow it down from there.

1. Gas (Is gas pressure good, is gas flow strong enough?)
2. Spark (are all spark plugs firing properly? Is spark strong enough)
3. Combustion at each cylinder (timing, pushrod adjustment)
4. Air Flow (MAF/MAP sensor working? Air Filter dirty?)

Appliance Repair Utah

Mar 25, 2012 | 1996 Ford Explorer

1 Answer

2002 cavalier, trac off light came on and then car died and could not get it started again


I would agree with the mechanic. Since the engine will start but dies, you can assume that the battery may be (barely) strong enough to start the vehicle but not strong enough to keep it running. After the engine starts, the alternator does the lions share of producing enough electrical energy to produce a strong spark at the spark plugs. If the alternator is not doing its job, the battery drain fairly rapidly and your engine will die. Within a fair degree of certainty, I would say that the "trac off" light will not occur after the alternator is replaced.
Best of luck!

Jan 12, 2012 | Cars & Trucks

2 Answers

Van will not start. Battery is strong. Starter is turning over, but suddenly - and without warning - the van will not start.


  • check fuel supply(pump)..if no fuel....
check fuel pump relays and fuel pump
  • check ignition (or spark)at the plugs..no spark check plugs/damaged plug leads/faulty coil pack

Jun 29, 2011 | Chevrolet Venture Cars & Trucks

1 Answer

While changing spark plugs one broke off & thread part still in the head, what is the best way to get it out.


You should still be able to get a spark plug socket on it. Unscrew it all the way until it is loose. I am assuming you have the engine where the spark plugs are recessed in the head and difficult to reach. What you need, once the remaining part of the plug is loose, is a very strong magnetic pickup tool that is long enough to reach the plug. Another option is to get a length of rubber hose just small enough to fit in the spark plug hole, but large enough to fit around the spark plug. Push the hose down over the spark plug. If it fits snug enough, you will be able to pull the plug out with the rubber hose. Good luck.

Dec 28, 2010 | 2004 Dodge Durango

Not finding what you are looking for?
1994 GMC Jimmy Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...