Question about 2006 Volkswagen Jetta

1 Answer

Power steering caution light is on - 2006 Volkswagen Jetta

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 41 Answers

Check your fluid levels, the owners manual should tell you where that is under the bonnet.

Posted on May 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you bleed the power steering on 2004 escape


CAUTION: If the air is not purged from the power steering system correctly, premature power steering pump failure can result. The condition can occur on pre-delivery vehicles with evidence of aerated fluid or on vehicles that have had steering component repairs.
  1. NOTE: A whine heard from the power steering pump can be caused by air in the system. The power steering purge procedure must be carried out prior to any component repair for which power steering noise complaints are accompanied by evidence of aerated fluid. Remove the power steering fluid reservoir cap. Check the fluid.
  1. Raise the front wheels off the floor. For additional information, refer to Section 100-02 .
  1. Tightly insert the stopper of the vacuum pump into the reservoir.
  1. Start the engine.
  1. Install the vacuum pump, apply vacuum and maintain maximum vacuum of 68-85 kPa (20-25 in-Hg).
  1. CAUTION: Do not hold the steering wheel against the stops for more than 3 to 5 seconds at a time. Damage to the power steering pump can occur. Cycle the steering wheel fully from stop to stop 10 times.
  1. Stop the engine.
  1. Release the vacuum and remove the vacuum pump.
  1. CAUTION: Do not overfill the reservoir. Fill the reservoir and install the reservoir cap.
  1. Visually inspect the power steering system for leaks.

Jul 26, 2016 | Cars & Trucks

1 Answer

Power steering pump 2007 Ford Edge located where? Can't seem to locate it..need to replace it; 3.5 engine


CAUTION: While repairing the power steering system, care should be taken to prevent the entry of contaminants or premature failure of the power steering components may result.
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02 .
  1. Using a suitable suction device, siphon the power steering fluid from the power steering fluid reservoir.
  1. Remove the RH inner fender splash shield. For additional information, refer to Section 501-02 .
  1. Using the special tool, disengage the power steering pump belt from the power steering pump pulley and position it aside.
    • Install the removal tool between the belt and the pulley and turn the crankshaft bolt clockwise to disengage the belt.
  1. Remove the 4 bolts and position the driveshaft aside.
  1. Using a suitable jack, support the rear of the subframe.
  1. Remove the 2 nuts, 4 bolts and the subframe support brackets.
  1. Remove the 2 middle subframe nuts.
  1. Lower the rear of the subframe.
  1. Release the clamp and disconnect the power steering supply hose from the power steering pump.
  1. Disconnect the power steering pressure (PSP) switch electrical connector.
  1. Remove the power steering pressure line fitting banjo bolt and disconnect the line from the power steering pump.
    • Discard the 2 seals.
  1. Remove the 3 power steering pump bolts and the power steering pump. This is a job best left to a qualified repair shop !

Jul 26, 2016 | 2007 Ford Edge

1 Answer

Steering wheel airbag removal on 2006 Cadillac cts cant find bolts


There are no bolts ! it takes a special tool , there are spring loaded Fasteners .
Pull the handle of the air bag tool away from the instrument panel (I/P) releasing one of the spring loaded fasteners.
Steering Wheel Inflatable Restraint Module Replacement
Tools Required J 44298 Driver Air Bag Removal Tool
Removal Procedure
Caution: Refer to
SIR Inflator Module Handling and Storage Caution in the Preface section.
Caution: Refer to SIR Caution in the Preface section.

showgif.do?image=640349

tif.gif
Caution: A deployed dual stage inflator module will look the same whether one or both stages were used. Always assume a deployed dual stage inflator module has an active stage 2. Improper handling or servicing can activate the inflator module and cause personal injury.
  1. Disable the SIR system. Refer to SIR Disabling and Enabling .
  2. On the back side of the steering wheel are 3 openings for removing the steering wheel module.
  3. Adjust and install J 44298 into 1 of the holes.
  4. Important: Seat the air bag removal tool all the way in to perform properly.
  5. Pull the handle of the air bag tool away from the instrument panel (I/P) releasing one of the spring loaded fasteners.
  6. Repeat this step for the other 2 fasteners.
  7. Pull the inflatable restraint module gently away from the steering wheel.
    showgif.do?image=818476
  8. tif.gif
  9. Important: Note the wire routing positions on the steering wheel module connectors, the redundant control routing positions, and the horn wire routing positions for the correct assembly.
  10. Remove the connector position assurance (CPA) (4) and the electrical connector from the steering wheel module.
  11. Remove the horn contact lead (2) from the steering column cam tower.
  12. Remove the steering wheel module (5

Mar 09, 2015 | 2006 Cadillac CTS

1 Answer

Why do my car lights stay on when the car is turned off


Button on top of steering column has either been pressed or gone bad. Press the button with the key out, if that doesn't give the desired effect then the button probably needs to be replaced. Caution, when working around the steering wheel the air bag can deploy.

Jul 03, 2014 | 2005 Subaru Outback

1 Answer

Is it very difficult to change the power steering pump in a 2004 kia sedona?


  1. Remove the Power Steering belt.
  2. Disconnect the power steering hoses from the power steering pump. Take caution as there may be some pressure.
  3. Remove the bolts holding the Power Steering pump to the pump mount.
  4. Install the new Power Steering pump.
  5. Reconnect the power steering hoses.
  6. Reconnect the Power Steering belt.
  7. Top off with fluid.
  8. Start up the vehicle.
  9. Turn the wheel to the left.
  10. Top off with fluid.
  11. Turn the wheel all the way to the right.
  12. Top off with fluid.
  13. Repeat the last 4 steps until the fluid level doesn't change much, and is topped off.

Feb 18, 2011 | 2006 Kia Sedona

1 Answer

How can you flush the steering gear box after removing old power steering pump 98chevy C1500 silverado? I dont want any old fluid to get in the new power steering pump.


Leave the return line disconnected from the pump and run into a bucket. fill new pump and start engine have some one keep adding fluid until clean fluid is going into bucket. Caution make sure to secure hose to bucket or you will make a mess. Also turning the steering wheel about a half turn in each direction Will help it to flush out the gear box better.

Feb 17, 2011 | 1998 Chevrolet K1500

1 Answer

2005 jetta power steering amber warning light, trouble ?


If you do not know what you are talking about you really should stay out of a conversation. It dose not have a power steering pump or a reservoir or suction! It is electronic and needs scanned with a computer. God people open mouth and insert huge foot. Stay with your night time job your dam sure no mechanic!

Jul 13, 2010 | 2005 Volkswagen Jetta

1 Answer

Steering wheel adjustment lever to raise or lower is broken and the turn signal lever on the steering is not working the turn signal lights wont light up so can these lever be replaced or do I replace...


yes they can be replaced , what you are looking for is called a combination switch . it maybe faster and as cheap to find a hole steering wheel at a auto salvage yard. keep in mind that then you would have to change key assembly and ether way use caution with air bag , if there is a chip in your key there is a fuse that has to be removed before disconnecting the battery.then under the dash there will be a yellow wire for the air bag that will have to be disconnected it will be labeled inflatable device caution or warning. if you should want any further help please feel free to ask . Thank you Have a grate day

Jun 24, 2010 | 2000 Pontiac Grand Am GT

1 Answer

How to r&r powersteering pump 1998 mercury grand marquis


Hopfully this will be ALL you need Besides Pulley REMOVAL TOOL It can be Rented @ AutoZONE

REMOVAL
  1. Remove drive belt.
  2. Raise vehicle on hoist. WARNING: TURN AIR SUSPENSION SWITCH (LOCATED IN LUGGAGE COMPARTMENT) OFF TO PREVENT VEHICLE DAMAGE OR PERSONAL INJURY.
  3. Remove power steering pressure hose bracket.
  4. Disconnect electrical connector at power steering control valve actuator.
    1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley hub. CAUTION: Do not apply in-and-out pressure on the power steering pump shaft. Pressure will damage the internal thrust areas.
    2. Hold the small hex-head and rotate the tool nut counterclockwise to remove the power steering pump pulley.
    3. Disconnect power steering pressure hose at power steering pump and drain fluid into a container.
    4. Disconnect power steering return hose at power steering pump and drain fluid into a container.
    5. Remove four retaining bolts and power steering pump and power steering pump pulley assembly.
    6. Remove power steering pressure switch from pump.
    INSTALLATION
    1. Position the power steering pump on the mounting bosses of engine block and install the bolts at the side of the power steering pump. Tighten to 20-30 Nm (15-22 ft. lbs.).
    2. Connect the power steering reservoir pump hose to the power steering pump and reposition the hose clamp to power steering pump inlet fitting.
    3. Replace power steering pressure hose O-ring.
    4. Install the power steering pressure hose to the power steering pump fitting. Tighten the tube nut with a tube nut wrench rather than with an open-end wrench. Tighten to 34-46 Nm (26-33 ft. lbs.). NOTE: Swivel or end play of the power steering pressure hose end is normal and does not indicate a loose fitting.
    5. Place the power steering pump pulley on the power steering pump shaft and install Power Steering Pump Pulley Replacer T91P-3A733-A. The small diameter threads on the tool should be engaged in the power steering pump shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group.
    6. Hold the small hex-head and rotate the tool nut clockwise to install the power steering pump pulley on the shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group. NOTE: The power steering pump pulley face must be flush within 0.25 mm (0.010 inch) of the end of the pump shaft.
    7. Remove the Power Steering Pump Pulley Replacer T91P-3A733-A.
    8. Remove the shipping tube nut from power steering pump housing prior to installation.
    9. Connect electrical connector to power steering control valve actuator.
    1. Install power steering pressure hose bracket.
    1. Lower the vehicle.
    2. If equipped, turn the air suspension ON.
    3. Install drive belt on the power steering pump pulley.
    4. Fill the power steering pump reservoir with Power Steering Fluid Motorcraft MERCON(r) ATF.

Oct 04, 2009 | 1998 Mercury Grand Marquis

2 Answers

Power steering pump replacement for Subaru Outback


REMOVAL

  1. Remove ground terminal from battery.
  2. Remove pulley belt cover bracket.



  1. Loosen lock bolt and slider bolt and remove power steering pump drive V-belt.
  2. Disconnect connector from power steering pump switch.



  1. Disconnect pipe C and suction hose from oil pump. CAUTION:
    • Do not allow fluid from the hose end to come into contact with pulley belt.
    • To prevent foreign matter from entering the hose and pipe, cover the open ends of them with a clean cloth.



  1. Remove bolts which install power steering pump bracket.



  1. Place oil pump bracket in a vise, remove two bolts from the front side of oil pump. CAUTION: Do not place oil pump bracket directly in the vise; use soft pads and hold oil pump lightly to protect the pump.



  1. Remove socket from oil pump.
  2. Remove bolt from the rear side of oil pump.

Jan 18, 2009 | 2002 Subaru Outback

Not finding what you are looking for?
2006 Volkswagen Jetta Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...