Question about 2008 Ford F-350

Open Question

2008 f350 particulate sensor(deisel)

Error code 2455, checked all three exhaust sensors and they have 211 ohms res each, they seem fine?

Posted by on

  • 2 more comments 
  • whisp878 May 02, 2010

    not sure Iam looking in the right place for the cause of engine error code,

  • whisp878 May 02, 2010

    is this error for the exhaust system or is it somthing else?

  • sultana7 May 11, 2010

    Here is your solution » BMW »
    Buick »
    Chevrolet » Chrysler » Dodge » Ford » GMC » Honda » Hyundai » Jaguar » Lincoln » Mazda » Mercury » Mitsubishi » Nissan » Oldsmobile » Pontiac » Saturn » Subaru » Suzuki » Toyota » Volkswagen » Volvo a

  • yadayada
    yadayada May 11, 2010

    ohm testing a sensor is not how to test them that is useless information, they put out a voltage signal, it should be varing between .25 and 1.00 volt

×

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 2008 f350 ford deisel 6.4 engine error code #2455

particulate filter sensor high circut sensor needs to be replaced

Posted on Apr 20, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is fault code 2003 on a mitsubitsi colt 3000i


Diesel particulate filter efficiency below threshold bank 2
Possible causes
Exhaust pressure sensor fault
Diesel particulate filter faulty
C/heck/replace exhaust pressure sensor
Check/replace Diesel particle filter

May 31, 2016 | Cars & Trucks

1 Answer

Need to fix my 2007 Dodge Ram 3500 dually,6.7 Cummings diesel, check engine light code P2002


P2002 - Diesel Particulate Filter Efficiency Below Threshold (Bank 1)
Description: The powertrain control module(PCM) monitors the efficiency of the diesel particulate filter for a concern. The efficiency of the filter is determined by the amount of restriction in the filter for a certain exhaust flow rate. The diesel particulate filter is preconditioned for 5,000 km (3,107 miles) before the PCM begins to monitor the level of restriction. The test fails when the measured level of restriction is less than the expected level calculated by the PCM. Possible Causes:
  • Dirty air cleaner element
  • Recent manual or thorough diesel particulate filter regeneration
  • Aftermarket accessories and performance modifications
  • Modified tailpipe
  • Exhaust leaks before or near the diesel particulate filter pressure sensor
  • Leaks in the diesel particulate filter pressure sensor connecting hose
  • Damaged diesel particulate filter
Diagnostic Aids: Check for leaks in the exhaust system. Check for aftermarket exhaust accessories and performance modifications that decrease the exhaust restriction. If a new diesel particulate filter was recently installed, verify the diesel particulate filter parameter reset procedure was carried out.

Feb 18, 2015 | Dodge Cars & Trucks

1 Answer

P2002 how to solve indicator ligth on dash board


Error Code:P2002
Description:
DTC P2002 Particulate Trap Efficiency Below Threshold (Bank1)
Possible solutions:
- Perform regeneration process. This process does not always solve the problem or the problem is solved for short term only.
- Remove/ Replace the Dust Particulate filter.
- Exhaust fuel addition INJECTOR ASSEMBLY. (Replace).
- Inspect turbo charger, in any.
- Mass Air Flow sensor.-
- Exhaust manifold convertor sub assembly

Mar 14, 2014 | 2007 Toyota Hi-Ace 220

1 Answer

Crank but does not start (Error code P0642)


p0642 = sensor reference voltage a circuit low voltage
p0300 = means random misfire
check firing order connections and must be in place.
check also cables especially the high tension cable and coils for required resistance.
primary = 1.0 to 0.5 ohms
secondary = 900 to 11,000 ohms (as requires per model)

Aug 15, 2012 | Infiniti Cars & Trucks

1 Answer

What does code p2459 mean?


Causes
- Exhaust leak
- Improperly installed or loose Exhaust Gas Temperature (EGT)
- Low engine compression
- Corroed fuel injector
- Water in the fuel system
_ fuel filter or water seperator fouled.
When is the code detected?
The P2459 will set if the Engine Control Module (ECM) detects that the average time between completed regenerations is less than a calibrated threshold.
Symptoms- Engine Light ON (or Service Engine Soon Warning Light)
P2459 Description The particulates in the exhaust gases are collected by the Diesel Particulate Filter (DPF). When the filter becomes saturated with particulates, they are incinerated by a regeneration process. The regeneration process increases the exhaust gas temperature, warning the Diesel Oxidation Catalyst (DOC) first, the warning the DPF. The Engine Control Module (ECM) monitors the system with inputs from two Exhaust Gas Temperature (EGT) sensors 1 and 2 and the exhaust differential pressure sensor.

Read more: http://engine-codes.com/p2459.html#ixzz1xGkI9BsX

Read more: http://engine-codes.com/p2459_gmc.html#ixzz1xGjSKrIa

Jun 09, 2012 | Chevrolet Silverado 2500HD Cars & Trucks

1 Answer

Trouble code p2452 ,p040d


The first code is for the Diesel particulate filter sensor and the second is for a high temperature on the EGR temperature sensor. Your truck may need a new Air filter and I would try doing that first. The EGR temperature may drop if the Intake air flow is better.

Have someone clear the computer with a scanner at Autozone, Oreillys, or Advance where they will scan for free. Also ask scan guy to get a reading on curb idle speed. You may be idling too low to have good exhaust flow. If the EGR temp remains high, you may have a blocked exhaust or a faulty sensor.

I hope my solution is very helpful in fixing your truck.

Apr 01, 2011 | 2008 Ford F-350 Super Duty

1 Answer

Are there exhaust sensors or are they called probes? on 2008 ford f250 6.4 turbo diesel


THERE ARE SEVERAL SENSORS:

EXHAUST GAS TEMPERATURE (EGT) SENSOR
EXHAUST PRESSURE (EP) SENSOR
DIESEL PARTICULATE FILTER PRESSURE SENSOR

HOPE THIS INFORMATION HELPS

Oct 17, 2010 | 2008 Ford F 250 Super Duty 4WD

1 Answer

2008 f350 ford deisel 6.4 engine error code #2455 what is it?


particulate filter sensor high circut sensor needs to be replaced

Apr 20, 2010 | 2008 Ford F-350

1 Answer

I have a 1999 F350 7.3 deisel. I was driveing and it just shout down, I check and there are no codes.


if you have ascaan tool that can check pids you need to view the cmp pid and the ipr pid if ipr is below 500 it will not run or the cam shaft sensor might have went bad there is a recall on them

Apr 12, 2009 | 2004 Ford F350

Not finding what you are looking for?
2008 Ford F-350 Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...