Question about 2001 Dodge Durango

1 Answer

How hard is it to replace the front drive shaft on a 2001 Dodge Durango 4X4?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 196 Answers

Not hard at all. If you climb under it and look, you'll see where it mounts to the front differential and to the transfercase. Grab some tools and have at it! Pretty simple job.

Posted on Apr 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to permanently disable 4 wheel drive in 2001 Durango. Can I drive the car with the front shaft removed?


yes
if the car is all wheel drive you will have to engage center diff lock
if ordinary 4 wheel drive there will be no problem because if you have it in 2 wheel drive high it is the same thing as having no front drive shaft installed

Feb 22, 2016 | 2001 Dodge Durango

1 Answer

Front left wheel grinds when you put my 2001 dodge Durango when you put itin 4 wheel drive..how do I fix this?


The c/v axle and output shaft on the front axle are worn where they spline together, they need to be replaced

Dec 14, 2014 | 2001 Dodge Durango

1 Answer

Remove 4x4 transmission of a dodge durango 4x4


a lot of those dodges have electrical solenoid shift pack assyemblies that cause the vehicle not to shift the kit comes with 4 solenoids and wires

May 12, 2014 | 2001 Dodge Durango

1 Answer

2002 Dodge Durango SXT 4.7L RWD shaking (serious vibration) badly between 70 to 80 mph


If it were me I would take out the drive shaft and check the play in the universal joints (I know you said they were replaced). Unlike ball joints they should exhibit good freedom of movement and flop from one position to the next as the shaft is rotated in the hand. Check that the bearing cup retaining clips are present on all sides. If there is any tightness in a bearing it is possible that either one of the cups has been pressed (hammered?) in too far or that a needle bearing was dropped from the outer race into the cup during assembly. Also check that the cup holders (arms) are not bent, sometimes if care is not taken to support the back of the 'arms' when installing the bearing cups the 'arms' will bend.

Feb 28, 2017 | 2002 Dodge Durango

1 Answer

4X4 makes a rattling noise when engaged?


sounds like it may have a front drive shaft u-joint that is bad

Feb 02, 2011 | 2001 Dodge Durango

1 Answer

Can t gear the 4 whel drive in my dodge durango


It is very likely that your TCCM or Transfer Case Control Module has given up the ghost.

I under stand they cost ~$400, but you can find one in a salvage yard and replace it yourself if so inclined.

The module is blue, and located under the dash near to the 4x4 switch.

Jul 12, 2010 | 2001 Dodge Durango

1 Answer

2001 dodge durango 4 wheel drive not working loud knocking


You need to check the cv joints in the front end or the u joints in the front drive shaft.If none of the above then the problem is internal in the front diff.

Jan 28, 2010 | 2001 Dodge Durango

1 Answer

Is there a free online diagram for dodge durango 2001 drive shaft


its pointing upward b/c thats what the pinon angle is set for that way there is no vibration when driving it. they sell pinion shims to place b/w the leaf spring and the axle to turn it more up or down

Sep 23, 2009 | 2002 Dodge Durango

Not finding what you are looking for?
2001 Dodge Durango Logo

594 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...