Question about 2002 Chevrolet Cavalier Coupe

1 Answer

Remove and replace rear turn signal light - 2002 Chevrolet Cavalier Coupe

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 53 Answers

Open up trunk and pull back any inside cloth trim to expose wing nuts. twist off wings nuts and the rear lamp assembly will then pull out from body. on the back of the lamp assembly is the connector / bulb assembly. this just twists off to unlock and remove from the lamp. replace bulb, lock bulb / connector back into place and the re-install the lamp assembly.

Posted on May 02, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 2000 Ford 150 Truck

Unscrew the light covers and you will see the bulb.

Posted on Jul 18, 2008

ndguy2481
  • 251 Answers

SOURCE: replace rear turn signal bulb

it's in the trunk behind the materail in the trunk

Posted on Sep 11, 2008

PetaPeta
  • 4 Answers

SOURCE: rear turn signal light bulb replacement

Yes, and easy access from the trunk. You will be able to remove the bolts from inside and the light assembly will be able to be pulled from the externior to replace all of them. It is not a real quick process, so when one goes out, I usually replace all of them.

Posted on Oct 21, 2008

seanpwright
  • 2030 Answers

SOURCE: replace rear turn signal light

open trunk, remove screws that hold tailight in, twist out bulb holder, take out bad bulb, reinsert buld holer, replace tailight, replace screws, close trunk...YOUR DONE.

Posted on Nov 08, 2009

  • 1 Answer

SOURCE: how to replace rear turn signal light bulb

I just changed my rear turn signal. Really easy. There is two 1/4 inch bolts visible when you open the tailgate. Take both of those out and gently lift the light housing out towards the outside of the vehicle. There is two small clamps on the other side of the fixture that just slide right out when you pull on it. There you go

Posted on Feb 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace rear signal light on driver side


Open the rear hatch, remove the screws that hold the rear taillight assembly to the vehicle. Find the socket for the bulb you need to replace and turn it counter clockwise. Remove the socket, then replace the bulb. Installation is the reverse.

Feb 10, 2014 | 2005 Saturn Relay

1 Answer

How to replace bulb in front bumper turn signal housing 1995 jag xj6


hello,
  • Identify the blown bulb. Note that if a headlight bulb has blown, the dip beam is on the outside and the high beam is on the inside. Turn off the ignition switch and light switches.

  • Open the hood and replace any blown headlight bulbs. Press the plastic spring clips and remove the bulb holder from the assembly. Pull the bulb out of the bulb holder and replace it with a new bulb. It only fits one way. Be sure not to touch the bulb's glass. Replace any parking lights at the same time, they are in the headlamp unit too.

  • Remove the front turn signal light unit in the bumper to change the turn signal bulb. Push gently on the inside edge and insert a blade between the bumper and the lens at the outside edge. Compress the spring and remove the lens. Fit a new lamp by inserting it into the plug. The side marker light is changed using a similar process.

  • Open the trunk to replace the rear fog light, stop light, tail light, reversing light and turn signal light. Remove the rear light cover and turn the bulb holder fastener 90 degrees counter clockwise. Remove the expired bulb, fit a new one and replace the parts, turning the bulb holder clockwise.

  • Thanks..

    May 21, 2011 | 1995 Jaguar XJ6

    1 Answer

    Left rear turn signal light replacment


    Hello,

    To replace the left rear turn signal light, please follow the steps below:
    1. Open the rear hatch of your van.
    2. There are two black button like protrusions behind the hatch next to the turn signal lamp.
    3. Pry these out and remove lens.
    4. Replace bulb.
    5. Then reverse the process th reassemble the hatch back together.
    Hope this helped. Thank You for using FixYa!!!

    Jan 12, 2011 | 2004 Chrysler Pacifica

    1 Answer

    I need to replace the driver's side brake light.


    Rear Combination Light- 2007 might vary from these diagrams:
    Removal & Installation 2004 (Early Production) 4 Door To Remove:
    1. Disconnect battery negative cable.
    2. Disconnect electrical connector. Rear Combination Light kia-06-18-7495.gif

    3. Remove 2 screws and 2 nuts and remove light assembly.
    To Install:
    1. Install light assembly and 2 screws and 2 nuts.
    2. Connect electrical connector.
    3. Connect battery negative cable.
    5 Door To Remove:
    1. Disconnect battery negative cable.
    2. Disconnect electrical connector. Rear combination light kia-06-18-7496.gif

    3. Remove 2 screws and push light assembly toward outside of vehicle. CAUTION
      Use care to not damage gasket.
    4. Pull rear combination light from vehicle.
    To Install:
    1. Install rear combination light and 2 screws.
    2. Install 2 screws.
    3. Connect electrical connector.
    4. Connect battery negative cable.
    2004 (Late Production), 2005-2009 To Remove:
    Turn Signal Lamp kia-06-20-7698.gif

    1. Disconnect battery negative cable.
    2. Remove 2 screws and cover inside trunk.
    3. Remove 4 nuts and disconnect electrical connector (A).
    4. Remove rear combination lamp.
    To Install:
    Turn Signal Lamp kia-06-20-7698.gif

    1. Install rear combination lamp.
    2. Install 4 nuts and connect electrical connector (A).
    3. Install cover inside trunk and install 2 screws.
    4. Connect battery negative cable.
    prev.gif next.gif

    Oct 28, 2010 | 2007 Kia Spectra5

    2 Answers

    Rear brake lights, rear turn signals inoperable. bulbs replaced and are working, simply not responding to brake or turn signal?


    If the third brake light always works, then it is the turn signal switch. If the third brake light does not work, it is probably something else. The turn signal switch is in the steering column. You have to remove the airbag and steering wheel, take out all of the componets and replace the turn signal switch. Special tools are required and a moderate level of mechanical ability. Watch the airbag, it can go off and cause serious injury!!

    Sep 24, 2010 | 2004 Chevrolet Malibu

    1 Answer

    O replace passenger side rear turn signal bulb on 2004 Cadillac


    open trunk, remove the plastic panel around the latch plate, remove the plastic mounting bolts that hold the grey trunk liners in place, there are two 10mm nuts that hold in the light remove nuts pull out light twist the bulb retainer out and replace bulb.

    Jul 12, 2010 | 2004 Cadillac CTS

    1 Answer

    How to change rear signal light on a 1997 chevy suburban


    LOWER REAR HATCH SHOULD BE TWO SCREWS ON SIDE OF LIGHT REMOVE AND TAKE LIGHT OFF MIDDLE LIGHT SHOULD BE SIGNAL LIGHT BULB PUSH TAB AND TURN LEFT TO REMOVE REPLACE BULB .

    Jan 28, 2010 | 1997 Chevrolet Suburban

    1 Answer

    Replace rear turn signal light


    open trunk, remove screws that hold tailight in, twist out bulb holder, take out bad bulb, reinsert buld holer, replace tailight, replace screws, close trunk...YOUR DONE.

    Nov 08, 2009 | 2000 Chevrolet Cavalier

    1 Answer

    I have a left front clearance light out how do you get it out 1


    Signal and Marker Lights REMOVAL & INSTALLATION Front Turn Signal and Parking Lights
    1. Disconnect the negative battery cable.
    2. At the rear of the front bumper, turn the bulb socket 1⁄4 turn and remove the socket from the parking brake housing.
    3. Remove the bulb from the socket; if necessary, replace the bulb.
    4. If lens replacement is necessary, remove the retaining bolts and remove the lens from the bumper.
    5. To install, reverse the removal procedures. Check the turn signal/parking light operations.
    Fig. 1: Common front turn signal/parking light mounting

    d16c14b.jpg
    Fig. 2: Twist and remove the bulb socket from the back of the turn signal/parking light lens

    8b774bd.jpg
    Fig. 3: If lens removal is necessary, loosen and remove the retaining bolts

    09f4811.jpg

    Jul 24, 2009 | 1992 GMC Sonoma

    1 Answer

    Replacing rear turn signal bulb in 2003 Mustang


    remove the trim panel at the very rear of trunk, remove it and place it out of the way, remove tail light Assembly retaining nuts top and bottom, I think there are 6 per side, pull the tail light assembly straight back to access the bulbs for replacement.

    Dec 04, 2008 | 2003 Ford Mustang

    Not finding what you are looking for?
    Cars & Trucks Logo

    160 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76109 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8269 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...