Question about 2003 Ford Explorer

1 Answer

Ignition key programming - 2003 Ford Explorer

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 180 Answers

You have to take to dealer about 40 to 50 bucks

Posted on Apr 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2002 Lincoln continental theft protection is on and won't let me program new keys


Greetings, I read your question and I think Reliable-Store can help you in this. Here's the site link.
Best Manuals

Jul 17, 2016 | Lincoln Cars & Trucks

1 Answer

How do I reset anti-theft on a 1996 Ford Mustang after replacing the ignition?


Ignition what ? Switch ,Ignition lock cylinder ? New keys ? do they have the transponder pellet in the head. Do you have a security lit flashing when trying to start the vehicle ?
SECTION 419-01: Anti-Theft - PATS 1999 Mustang Workshop Manual GENERAL PROCEDURES Procedure revision date: 11/06/1998 Key Programming -Erase All Key Codes and Program Two Keys
Special Tool(s) > New Generation STAR (NGS) Tester or equivalent
418-F048 (007-00500) NOTE: This procedure is used when a customer needs keys programmed into the system and does not have two programmed ignition keys available. This procedure is also useful when programmed ignition key(s) have been lost or the ignition switch assembly has been replaced, and it is desired to erase key(s) from the passive anti-theft system (PATS) memory.
NOTE: This procedure will erase all programmed ignition keys from the vehicle memory and the vehicle will not start until two keys have been reprogrammed to the vehicle.
NOTE: Two PATS encoded keys with the correct mechanical cut must be available to perform this procedure. One or both of them may be the customer's original keys.
NOTE: If additional keys are to be programmed, refer to Key Programming - Program a Key Using Two Programmed Keys. If the remaining keys are with the customer and are not available with the vehicle, then instruct the customer to refer to the Owners Guide under the "Programming Spare [SecuriLock ® (North America), Safeguard ® (U.K.) or PATS for all other markets] Keys Procedure" for instructions on programming the remaining keys.
  1. Turn the ignition switch from OFF to RUN.
  1. Enter New Generation STAR/Service Bay Diagnostic System (NGS/SBDS). Follow the SECURITY ACCESS PROCEDURE to obtain security access.
  1. From NGS/SBDS menu, select IGNITION KEY CODE ERASE.
  1. NOTE: Do NOT select any additional commands from this menu.
    Turn the ignition switch to OFF and disconnect NGS.
  1. Insert the first encoded key into the ignition lock cylinder and turn the switch to RUN for three seconds.
  1. Insert the second encoded key into the ignition lock cylinder and turn the switch to RUN for three seconds.
  1. The vehicle should now start with both ignition keys.
You'll need to take to the dealer

Mar 19, 2015 | Ford Mustang Cars & Trucks

1 Answer

Programming ingition key with a chip in it



  • For 1998 and newer Fords there is no way to program a new Transponder key unless you have two already programmed keys. 1998 and older you could do this in about three minutes. This one has to be hooked up to a scanner.

  • Now if you do have two keys already programmed then follow these steps.
  1. Insert first programmed key in the ignition.
  2. Turn the ignition to start (run) for two seconds and back to off. The ignition should stay on for at least one second.
  3. Remove that key and within 10 seconds stick the second programmed key into the ignition. Turn the ignition to start (run) for two seconds and back to off. The ignition should stay on for at least one second.
  4. Remove the key.
  5. Now insert the key needing to be programmed into the ignition (within 20 seconds) and turn the ignition to start (run) for two seconds and then back off.
  6. The security light will light up for 3 seconds indicating the key is now programmed.
  7. Now wait a couple minutes before starting your car and your done.
  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards, Tony

Oct 06, 2011 | 1999 Lincoln Continental

1 Answer

I had a key made and it desabled the security system in my 1999 mercury cougar and now the car wont start and I need to have it reset.


All you have to do to reset the antitheft system is to lock the doors with the key fob.

Your new key has to be programmed to your engine computer (PCM) before it will work.

To program, follow the directions in your owner manual. You need 2 already rpogrammed keys to do this.

If you don't have 2 programmed keys, your dealer will have to use his diagnositc tool to retrieve the information from the computer. Always have 2 programmed keys. I actually keep 3 in case I lose one, I still have 2 to program a 3rd one myself.

If you have AAA, have it towed to the delaer as a "no Start" so you don't have to pay the tow charge.

I assume this new ket is your only key now, or you could drive to the dealer with your spare key.
-------------------------------------------------
SECTION 419-01B: Anti-Theft - Passive 1999 Cougar Workshop Manual GENERAL PROCEDURES Procedure revision date: 09/14/2001
Key Programming Using Two Programmed Keys NOTE: This procedure only works if two or more programmed ignition keys are available and it is desired to program additional key(s). If two keys are not available. For additional information, refer to Key Programming - Erase All Keys and Program Two Keys in this section.
NOTE: PID SPARE - KY must be enabled for this procedure to operate. If this PID is not enabled, refer to Security Access then select Spare Key Programming Switch; Enabled.
NOTE: If the programming procedure is successful, the new key(s) will start the vehicle and the anti-theft indicator will illuminate for approximately three seconds.
NOTE: If the programming procedure is not successful, the new key(s) will not start the vehicle and the anti-theft indicator will flash. If the programming procedure was not successful leave the ignition switch in the RUN position for at least 30 seconds, repeat the Key Programming procedure from Step 1. If the failure repeats, refer to Diagnostic and Testing to review DTCs an carry out Pinpoint Tests.
NOTE: A maximum of eight ignition keys can be programmed to a passive anti-theft system (PATS) equipped vehicle.
NOTE: If the steps are not carried out as outlined, the programming procedure will end.
NOTE: Ignition keys must have correct mechanical key cut for the vehicle and must be a PATS encoded key.
  1. Insert first programmed key into ignition lock cylinder and turn the ignition switch from the OFF position to the RUN position (maintain ignition switch in the RUN position for one second).
  1. Turn ignition switch to the OFF position and remove the first key from the ignition lock cylinder.
  1. Within five seconds of turning the ignition switch to the OFF position, insert the second programmed ignition key into the ignition lock cylinder and turn the ignition switch from the OFF position to the RUN position (maintain the ignition switch in the RUN position for one second).
  1. Turn the ignition switch to the OFF position and remove the second key from the ignition lock cylinder.
  1. Within ten seconds of turning the ignition switch to the OFF position , insert the unprogrammed ignition key (new key) into the ignition lock cylinder and turn the ignition switch from the OFF position to the RUN position (maintain the ignition switch in the RUN position for one second).
  1. If it desired to program additional key(s), repeat the applicable key programming procedure from step 1.
  2. ----------------------------------------------------------------------------------------------------------------------------------
Passive Anti - Theft System (PATS)
The Passive Anti-Theft System (PATS) is fully passive in operation and requires no special procedures by the driver to arm or disarm the system. It is invisible to normal scrutiny and is operated by a miniature transponder within the key body. The transponder communicates with the powertrain control module through a transceiver mounted around the ignition switch lock barrel. The PATS functionality is incorporated within the powertrain control module.
PATS may be identified by a larger than normal sized ignition key. A larger sized ignition key indicates the presence of the transponder that controls the system.
The transponder code reading is carried out when the key, having been inserted into the ignition lock barrel, is turned from position ``0'' to position ``II'' to crank the engine. If the PCM receives the correct code, the engine will start. If the PCM receives either no code or an incorrect code the engine will not crank and PATS remains armed and the engine immobilised.
Anti-Theft Indicator
Whenever the ignition is switched on the anti - theft indicator will remain on for three seconds while the system reads the ignition key code.
The anti - theft indicator will flash rapidly or glow continuously after the initial three seconds to indicate the PATS has immobilised the vehicle.
For additional information on the PATS fault codes, refer to the Diagnosis and Testing section
-------------------------------------------------------------------------
The PATS uses a specially encoded ignition key. Each encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique electronic identification code out of over four quadrillion combinations.
Each encoded ignition key must be programmed into the vehicle's powertrain control module (PCM) before it can be used to start the engine. There are special diagnostic repair procedures outlined in this manual that must be performed if an encoded ignition key needs to be replaced
------------------------------------------------------------------------

Dec 16, 2010 | 1999 Mercury Cougar

1 Answer

How do you program the keyless remote on a 2002 Intrigue?


1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.
8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.
9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).
10. Perform the previous step to program up to four transmitters (including your old ones).
11. Remove the ignition key in order to exit the Program Mode.


Good luck and thank you for using Fixya

Mar 09, 2010 | 2002 Oldsmobile Intrigue

1 Answer

Flashing alarm light after battery change. Car wont start,


System operation
System arms 5 seconds after switching ignition OFF. Switch ignition ON. Ensure clock LED illuminates for 3-5 seconds. If LED flashes rapidly at regular intervals for approximately 1 minute, then flashes at irregular intervals: Key code not recognised. Remove key and try again.
Programming
When
System malfunction: LED illuminates for 1 minute, then flashes at irregular intervals. Key(s) added or replaced.
NOTE: Replacement keys MUST have blue mark. Keys with red mark are NOT compatible with this system.
How
NOTE: Programming method using vehicle keys can be deactivated using diagnostic equipment.
Obtain 2 programmed keys (A and B). Insert key A into ignition switch. Turn ignition switch to position II. Wait 1 second. Switch ignition OFF. Remove key A. Insert key B into ignition switch within 5 seconds. Turn ignition switch to position II. Wait 1 second. Switch ignition OFF. Remove key B. Within 10 seconds: Insert key to be programmed into ignition switch. Turn ignition switch to position II. Wait 4 seconds. Switch ignition OFF. Wait 5 seconds. Start engine. If engine does not start and clock LED flashes: Switch ignition ON. Wait at least 20 seconds. Switch ignition OFF. Repeat programming procedure. Repeat above procedure to program remaining keys. Keys can also be programmed using diagnostic equipment

Mar 08, 2010 | 2000 Ford Focus

3 Answers

Reset immobiliser


u must put a key to ignition and open a drive door 3 times and press and hold lock button

Jan 18, 2010 | 2007 Ford F

1 Answer

For dgnoid: Car is 2002 Buick Regal. Husband is blind and I thought it would be cool for him to have remote key to lock and unlock car more easily, unfortunately, it did not come with instructions on how...


IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be using on the vehicle. Once you program the remotes , all previous codes will be erased from the memory. The other remotes will not be functional until you program the remotes again.
1. Close the vehicle doors.
2. Insert key in ignition and turn to ON (As far as you can without cranking engine)
3. Turn ignition OFF and remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key.
| (Do not turn the ignition key in the lock cylinder.)


6.
Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder.)


7.
Insert the ignition key into the ignition lock cylinder. (Do not turn the
ignition key in the lock cylinder.) Leave the ignition key in the ignition lock
cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order to
verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless entry
transmitter and hold until the vehicle beeps twice to verify that the
transmitter has been successfully programmed (this take approximately 15
seconds).

10. Perform the previous step to program up to four transmitters (including your
old ones).

11. Remove the ignition key in order to exit the Program Mode.


Jun 29, 2009 | 2002 Buick Regal

1 Answer

Programing remote contr ol


IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be using on the vehicle. Once you program the remotes , all previous codes will be erased from the memory. The other remotes will not be functional until you program the remotes again.
1. Close the vehicle doors.
2. Insert key in ignition and turn to ON (As far as you can without cranking engine)
3. Turn ignition OFF and remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key.
| (Do not turn the ignition key in the lock cylinder.)


6.
Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder.)


7.
Insert the ignition key into the ignition lock cylinder. (Do not turn the
ignition key in the lock cylinder.) Leave the ignition key in the ignition lock
cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order to
verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless entry
transmitter and hold until the vehicle beeps twice to verify that the
transmitter has been successfully programmed (this take approximately 15
seconds).

10. Perform the previous step to program up to four transmitters (including your
old ones).

11. Remove the ignition key in order to exit the Program Mode.

Jun 08, 2009 | 1999 Buick Regal

1 Answer

I lost my key and the ford dealership by my house sad i need to reprogram a chip but the car is a 1999 tuaruse and its to old to pull up what can i do


Here is the factory procedure to program a new key(s), I recomment only factory keys, you need to use the working key to do the procedure;
1. Insert a previously programmed coded key into the ignition.

2. Turn the ignition from the 3 (OFF) position to the 4 (ON) position. Keep the ignition in the 4(ON) position for at least one second, but no more than 10 seconds.

3. Turn the ignition to the 3 (OFF) position, and remove the coded key
from the ignition.

4. Within ten seconds of removing the previously programmed coded key, insert the other previously programmed coded key into the ignition.

5. Turn the ignition from the 3 (OFF) position to the 4 (ON) position. Keep the ignition in the 4 (ON) position for at least one second but not more than 10 seconds.

6. Turn the ignition to the 3 (OFF) position, and remove the second key from the ignition.

7. Within twenty seconds of removing the previously programmed coded key, insert the unprogrammed key (new/valet key) into the ignition.

8. Turn the ignition from the 3 (OFF) position to the 4 (ON) position. Keep the ignition in the 4 (ON) position for at least one second.

9. Your new unprogrammed key is now programmed. If the key has been successfully programmed it will start the vehicle’s engine and the theft indicator light will illuminate for three seconds and
then go out. If the key was not successfully programmed, it will not start your vehicle’s engine and the theft indicator light will flash on and off rapidly. If failure repeats, bring your vehicle to your dealer to have the
new key(s) programmed.

To program additional new unprogrammed key(s), repeat this procedure
from step 1 for each additional key

Jul 25, 2008 | Ford Taurus Cars & Trucks

Not finding what you are looking for?
2003 Ford Explorer Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...