Question about 1991 Toyota Land Cruiser

Open Question

Timing belt diagrams for 1991 toyota landcruiser 4l non turbo diesel. Thank you

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
short shadey
  • 421 Answers

SOURCE: belt diagram

bbce854.jpg
here you go please rate -Jeff

Posted on Sep 13, 2008

Ad
Saaboheme
  • 76 Answers

SOURCE: 1993 saab 900 belt diagram

Sorry, I don't have access to a Bentley now. There are 4 belts, 2 for alternator etc, 1 for aircon and 1 for pwr steering.
The power steering belt goes round the power steering pump & crank pulley only.
The paired belts go round crank pulley, alternator and water pump.
The aircon belt goes round crank pulley, aircon compressor and tensioner.
Alternator / water pump pair are closest to the engine.
Power steering is in the middle (with aircon) or closest to the bulkhead (without aircon).
Aircon (if fitted) is closest to the bulkhead.

(1) If you do not have an AC compressor, skip this step and go to step 2. If you dohave one, begin by cutting any cable ties that hold the main wiringharness to the AC hoses. Lift the harness up and over onto the camcover until it's near the PCV valve, and is now out of your way.

All nuts & bolts in this step are 13 mm.

Then, slacken the 2 bolts attaching the AC tensioner pulley mount (athick triangular steel plate) to the head. Use a long box wrench (ringspanner, in Englishicon_cheesygrin.gif ).

Using a deep-wall socket (or an offset ratchet wrench, or plain wrench)on the adjuster nut, back it off until there's no more tension in thebelt (you won't be able to remove the belt yet, though).

Now, remove the upper of the 2 mounting bolts and its washer, and pivot the tensioner down; remove the belt.

Remove the lower bolt, and lift out the tensioner. Look the triangularplate over for cracks, and spin the pulley to see if its bearing issmooth and quiet. (If you find problems, the pulley is about $15 and www.eeuroparts.com sells the entiretensioner assembly for something like $70.) Back off the adjuster nutuntil it's about 1/4" (1/2 cm) from the end of its threaded rod (usevise-grips to clamp the rod's other end onto the triangular plate, orput the whole thing in a vise).

(2) Slacken the bolt and nut holding the power steering pump to thehead and to the RH engine mount, respectively. Slacken the adjuster nut(yes, anotherthreaded-rod type thing) by about 1/2" (1 cm). You can use a normalwrench for this, but it takes forever--so I made a special tool bytaking a cheapo 13 mm open-jaw wrench and bending it to a 45-degreeangle just below the jaws (cut it to length if it's too hard tomaneuver). Loosen the mounting nut until it's almost off (but not completely off,or you'll lose the bolt it screws onto--this bolt was designed to fallout when the nut is removed). Pull the nut end of the threaded rodtowards the firewall to get it of the adjuster fork. Push the pumptowards the engine centerline and pull its belt off (you may need topry with a screwdriver to get it out of the pump pulley completely).

(3) Slacken the 16 mm nut on top of the alternator. Back off the alt.adjuster's 10 mm nut about 1/2" (1 cm)--a ratcheting wrench helps here.(This is the last threaded rod--I promise.) Completely remove the 16 mmnut, and pull the adjuster towards the firewall until it's out of thealt.

Now for the clever part: Cut yourself a wedge from a piece of wood (2 x4 is perfect), with a rise of 3" (8 cm) and a run of about 12" (30 cm).Push the alt. towards the engine, and shove the wedge in between theside of the alt. and the coil-spring tower (master cylinder mountingbracket works, too). Keep pushing the alt. and driving the wedge downuntil the alt. is so close to the engine that it's compressing thelower heater hose.

Pull the outer belt off the alt. pulley. Working from the RH side ofthe car, lift the belt off the water pump pulley and then disengage itfrom the crank pulley. Now, pull the inner belt into the outergroove of the water pump pulley. Go back to the LH side of the car, andmove the inner belt into the alt. pulley's outer groove. Try removingit from this pulley; if too difficult, either wedge the alt. closer tothe engine or try pulling the belt off the water pump pulley from theRH side of the car (a helper is very useful for all this).

(4) Install the new inner belt by fitting it into its groove in thecrank pulley first. Work it into the outer grooves of the alt. andwater pump pulleys, then into the inner ones. Install the outerbelt--again, first onto the crank pulley, then the water pump and alt.pulleys.

Remove wedge. Insert tensioner into alt. making sure the threaded rodsettles into its fork, and refit its 16 mm nut--but don't fully tightenit yet. Tighten 10 mm adjuster nut until belts can be pushed in only1/2" (1 cm) by thumb pressure (applied 1/2 way between water pump andcrank pulleys).

(5) Push PS pump as close to engine centerline as possible, andfinger-tighten its mounting bolt to hold it there. Fit a new beltaround the crank pulley first, then work it into the pump pulley groovefrom the bottom of the pulley until it pops in. You may need to use both hands, and/or carefully pry the belt on with a screwdriver.

Loosen the bolt you just tightened. Pull the pump away from enginecenterline, insert threaded rod into its fork (you may have to back theadjuster nut off some more), tighten the mounting nut (but notcompletely), and screw in the adjuster nut until the belt deflects asdescribed in (4) above.

(6) Start the engine. Blip throttle, watching the belts deflect as theengine speed goes up and down. If the "blur" you see midway down eachbelt is over 1" (2 cm) wide, tighten the belt(s) until it isn't. Tighten the PS pump mounting nut and bolt, and the 16mm nut on the alt.

If your car doesn't have AC, your belt replacement is over!

(7) If you haveAC, reattach the tensioner to the head with the lower bolt only (andleave this bolt finger-tight). Fit the new belt around the crankpulley, then around the compressor pulley and, finally, around thetensioner.

Reinstall the top tensioner bolt and its washer. Be careful and patienthere--you're threading a steel bolt into aluminum, so make sure it goesin straight. You may have to back off the tensioner nut a little. Leavethis bolt finger-tight.

Screw in the adjuster nut to get the deflection as described in (4)above. Start the engine, and blip the throttle. Watch belt's "blur" on LHside of engine. Adjust as in (6). Switch on compressor, and repeat.

If satisfied, tighten the 2 tensioner bolts. Return wiring harness toits original position, and re-secure with cable ties if needed.

Posted on Dec 16, 2008

  • 1 Answer

SOURCE: Timing belt light of Toyota LandCruiser 2006

the reset procedure of the timing belt light is all done by pressing the trip meter button and holding it in whilst the ignition is turned to on then select from the trip button then continue pressing until you come to 15 on trip metre, turn off and then restart. The light should then go off.

Posted on Jan 13, 2010

  • 1403 Answers

SOURCE: diagram for fan belt routing on a cummins 24 valve

web resourceful.com for complete auto manuals online. hope i helped!!

Posted on Aug 16, 2010

  • 1 Answer

SOURCE: workshop manual for toyota surf,2.4 turbo diesel

hi my toyota surf i cant take it out of 4 wheel drive if i do it try to jump back into 4 wheel drive when driving along

Posted on Jan 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

At what stage does the factory reccomend a timing belt replacement?


most diesel timing belts need to be changed every 60 to 80 thousand miles alway worth getting checked as if it snaps or skips teeth it can cause serious damage to the engine

Oct 19, 2014 | Cars & Trucks

1 Answer

No lights working


Have the ECM/ CPU checked out as reverse polarity does wonders for burning out the systems . You may be lucky as a reset using a scanner may fix it

Mar 28, 2014 | Toyota Land Cruiser Cars & Trucks

1 Answer

Fuel economy HJ75 landcruiser ute 1989 with turbo


Check that the intercooler is in good condition (no cracks or leaks) and the hoses are tight at the hose clamps . Next talk to a diesel pump repair specialist as you may have to re-tip the injectors and re-calibrate the pump for the extra air that the turbo produces. Check that you have the correct turbo for the diesel

Mar 14, 2014 | Toyota Cars & Trucks

1 Answer

Land cruiser vx turbo diesel 1990 80 series.


Track down Toyota publication RM184E - a search of the ih8mud forums is a good start to finding it.

Mar 12, 2010 | 1990 Toyota Land Cruiser

1 Answer

Timing belt replace on 1991 dodge stealth 3.0 24valve non turbo diagram


My apologies for the delayed response. I am going back and answering questions that were never answered.
Click on the following Link. It has all the Diagrams for the Timing Belt you will need.
Before Clicking, let me know if this helped.
Again my sincerest apologies,,..

http://www.2carpros.com/car_repair_information/year/1991/make/dodge/model/stealth/1991_dodge_stealth_timing_belt_diagram_marks.htm

Jan 12, 2010 | 1991 Dodge Stealth

1 Answer

Can you tell me the type of my engine by number 0080682 on Toyota landcruiser 80 vx, 1995 4200 diesel turbo


Market JapanYear 05/1999Make TOYOTAModel LAND CRUISERFrame HDJ101

Vehicle characteristics
GRADE: VXL: VXL TYPE DESTINATION: JPN: JAPAN ENGINE: 1HDFTE: 4200CC DIESEL TURBO TRANSMISSION: ATM: AUTOMATIC TRANSMISSION GEAR SHIFT TYPE: 4FC: ATM, 4-SPEED FLOOR SHIFT COLOR CODE: 057
TRIM CODE: FG41

Jan 08, 2010 | 1995 Toyota Land Cruiser

1 Answer

I need a diagram of a 1991 toyota camry motor to replace a timing belt


some one directed me to autozone.com where i found what i was looking for. it is free once you register your car information. thank you so much.

May 18, 2009 | 1991 Toyota Camry

1 Answer

How do i get to the tappets on a 100 series turbo landcruiser


you dont i think they are just shims mesure theshims dont mix up,mesure the gap firstwrite them down then add or replace shims

Jan 05, 2009 | 2001 Toyota Land Cruiser

2 Answers

Toyota Landcruiser 4.2lt diesel OR 3lt turbo diesel prado


The cruiser as long as its the turbo diesel, direct injection (4.2td), be aware though that this model has inherent "sag" with the IFS suspension, so if buying secondhand then upgrade the torsion bars(and factor this into your buying price).

Sep 13, 2008 | 2004 Toyota Land Cruiser

Not finding what you are looking for?
1991 Toyota Land Cruiser Logo

Related Topics:

422 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...