Question about 2006 Chrysler Town & Country

2 Answers

Where is the turn signal flasher located?

Where is the turn signal flasher? My signals works sometimes, sometimes not. Sometimes speed up, sometimes normal. 4 way flashers works fine. I read somethign about Turn signal switch on the column, is the flasher in that unit instead of a seperate unit?

Posted by on

  • winkie9 Apr 30, 2010

    I already checked the bulb. When not working, 4 way flashers work. I jusdt called the dealer and with a little time and he talking to the techs, it appears there is not a FLASHER seperate on these 2006 T&C minivans. It is one of two things.....the signal control switch (roughly $65) or a control module (about $170). I will have to do some more trouble shooting. Maybe the onboards Diagnostic will code for it next time it isn't working?

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 40 Answers

Bump...
Does anyone know where the FLASHER is located for this vehicle??

Posted on Mar 09, 2015

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 27 Answers

You more likely have a bulb that is no good. The next time your signals aren't working, pull over and check to see which bulb isn't working. Make sure the turn signal is on while checking. It should only be the left or right. Not both. Sometimes you can see the blown bulb with the hazards on depending on your model vehicle. Simply check the bulb thats not blinking for a tight fit. Then replace it if thats not the cure.

Posted on Apr 30, 2010

  • kevinsane_20
    kevinsane_20 Dec 12, 2012

    not even close to what the guy was asking about ...

  • Sam St
    Sam St Nov 30, 2013

    is it controlled by the computer??

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What would cause the turn signals to work sometimes and sometimes not ?


A bad flasher relay would do that. They are usually located on the fuse panel and plug into it.

Jun 27, 2014 | 1992 Ford Tempo

1 Answer

Turn signal flasher relay location in


Turn signals use what is called a flasher to regulate the speed at which the lamps turn on and off. Usually mounted in the fuse box. I have attached the replacement model for a 1996 Roadie. Should take all of 15 seconds to replace.

Mar 16, 2014 | Buick Roadmaster Cars & Trucks

1 Answer

My turn signals works sometimes and then wont work at all


Drivers side of steering column under dash, check flasher make sure its tite, turn key to on, turn signal on, move flasher round see if turn signal starts working replace flasher try it agian might be bad connection

Feb 18, 2013 | 1998 Cadillac Eldorado

1 Answer

Turn signals and flashers 97 olds cutlass only work sometimes


sounds like a bad flasher switch. wiggle flasher switch when turn signal is on to see if it makes it work or not

Sep 14, 2012 | Cars & Trucks

1 Answer

My left blinker sometimes works and sometimes doesn't and also sometimes I hear a clicking noise when I turn it on then it quits working. Is there a flasher relay for the turn signal, and if so where...


there is a flasher relay for the signals and its located behind the dash on the drivers side sometimes in the lower area of the dash.when the signals are working listen to the clicking noise to narrow down the area the flasher will be in.if all else fails you can go to the library and look for a book on your car and it will have the location in it.also if you know a tech he can help you locate it as well.

Sep 12, 2011 | 2004 Chevrolet Tahoe

2 Answers

Where is the turn signal flasher located on a 1992 oldsmobile cutlass cirea


SOMETIMES THE FLASHER IS IN THE FUSEBOX , SOMETIMES IT WILL BE UNDER THE DASH NEAR THE STEERING COLUMN. THERE ARE TWO FLASHERS ONE FOR TURN SIGNALS & ONE FOR HAZARD LIGHTS. THE TURN SIGNAL FLASHER MAY BE YELLOW & ONE OF THE WIRES WILL BE PURPLE. YOU CAN TURN ON THE HAZARD SWITCH IF THEY WORK YOU CAN LOCATE THAT FLASHER BY THE CLICKING SOUND & ELIMINATE THAT FLASHER & LOOK FOR THE YELLOW PLASTIC ONE. A SMALL MIRRIO MAY BE HELPFUL UNDER THE DASH.

Dec 26, 2010 | 1992 Oldsmobile Cutlass Ciera

1 Answer

Where is the turn signal flasher located in the 1997 malibu?


You are looking for (typically) a cylindrical device 1-1 1/2 inches in diameter and 2-2 1/2 inches tall. These can be mounted in any position and often are pushed into a spring clip holder. Most have three male connectors although some may have only two.

Sep 21, 2009 | 1997 Chevrolet Malibu

1 Answer

Flasher is screwed up


This sounds like a bad flasher unit. Simply by replacing this unit should fix this problem. Usually they are located on the top of the steering wheel beneath the trim. You have to disassemble the trim around the steering column.

Jun 09, 2009 | 2002 Lincoln LS

1 Answer

Turn signals and emergency flashers quit working.


check and replace the flasher unit if necessary, sometimes located in the fuse box area, sometimes under the dash near the steering column

May 18, 2009 | 1997 Ford Taurus

1 Answer

Turn Signals work intermitently on 2000 Dodge Ram 1500 Pickup


My turn signals worked fine until last night when I ran my battery down and had to get a jump. I realized right away that my turn signals suddenly didn't work. My theory hasn't been tested, but I am going to unhook my battery cables and reconnect again to see if that does anything. If not, I'll check out the steering wheel and that big square thing by the fuses. Thank you for all the posts and I was so happy to find this web page!

Dec 05, 2008 | 2000 Dodge Ram 1500 Truck

Not finding what you are looking for?
2006 Chrysler Town & Country Logo

794 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...