Question about 1996 Chevrolet C1500

1 Answer

I have a 1996 chevy 1500 4 wheel drive truck. I'm getting a noise from the back of the truck when I push the gas pedal down while driving . it stops when i let the gas pedal off going over 45 mph. The noise also doesn't happen when going into reverse only in forward at low speeds. it sounds like a whirr noise. thanks for any help.

Posted by on

  • gtoman2002 Apr 30, 2010

    I checked the drive shaft. it doesn't have the rusty powder. and I pushed it up and down with no movement. in it. it has has push button 4 wheel drive. I'm going to jack the back of the truck up and put it on stands to hear were the noise is really comming from

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 1,146 Answers

A good thing to check is the universal joints on your rear drive shaft. When they get worn, one of the first symptoms is a noise/ vibration that only occurs at certain speeds. Sometimes you can visually inspect them, and see signs of rusty powder coming out of the bearing caps.

Posted on Apr 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2004 chevy silverado 1500 4 wheel drive wont work..


try selecting from nutreul or less then 3km

Feb 02, 2010 | 2003 GMC Sierra

2 Answers

Need a 1996 1500 chevy 305 EXPERT!!!! ONLY!!!


Take an analog ohmmeter, remove connector from TP sensor, and touch probes on terminals of sensor, try combination of 2 until you see reading increase as gas pedal pushed & decrease as pedal released by someone, while engine off, and key off.. Have them slowly, & gradually push pedal, as you watch meter. Reading should increase slowly & gradually as well. If you see it climbing, then quickly drop off, then jump back up, it's faulty. Try to concentrate more on the position of gas pedal where you experience the engine cutting out. Costs nothing to try it.

Oct 16, 2009 | 1996 Chevrolet K1500

2 Answers

2000 Chevy Silverado 1500 4 wheel drive makes a scraping noise when turning


check the cv axles for wear such as torn rubber boots, when in 4 wd the noise should be even worse

Sep 15, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Grinding in and out of 4 wheel drive


You say 'new' truck, 09? or new used? I have had 3 Fords, 3 w/ manual trans. case, if you go into 4x4 Low range, you must come to a complete stop before shifting the trans. case to 4x4 mode, and I always put trans (automatic) in neutral before slipping into 4x4, it engages smoothly, no grinding. 4x4 high range can be put in while moving, but I would let off the gas pedal, shift to 4x4 high range, then resume accelerating. If there is any grinding going on doing it as above, something isn't right. Check the trans. case fluid level also, to make sure that's not an issue.

Aug 15, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

Stuck in 4 wheel drive and wont come out.


hey there i cant tell you what you are missing but i can tell you how to disengage the front wheels . ok you have a vacum line that runs right under the battery and a line that comes up from the front diff. to the same place ( you may have to remove batt and batt tray to get full access to this) un bolt it and temporaly put batt and batt tray back in start it up and decompress this and see if it comes out .... you should here clunking noise if it goes back in ... if thats the case just pull that big vaccum line off .... to test get all four tires off the ground and have some one put it in drive but dont hit the gas it should turn on its own ...if that dont work check the cable that runs down to the differental

Aug 04, 2009 | 2000 Chevrolet Silverado 1500

1 Answer

Loud Knocking when pressing on gas pedal


What you are describing sounds like you have an engine bearing failing. Do not drive it 'till you have it diagnosed and repaired (most times though it's too late when you hear it.)..... Outside chance it could be the trans flex plate but I doubt it.

Apr 22, 2009 | 1998 Chevrolet Tracker

2 Answers

1996 gmc 1500 four wheel drive


Have you checked the switch on the transfer case? Those switches tend to go bad and primarily operated the 4 wheel Hi.

Apr 13, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

4 wheel drive makes noise while in 2 wheel drive


There should be a plug on the front/steer axle. unplug the actuator. this should unlock it.

Mar 21, 2009 | 1996 Dodge Ram 1500 Club Cab

Not finding what you are looking for?
1996 Chevrolet C1500 Logo

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...