Question about 2005 Chevrolet Trailblazer Ext

1 Answer

I have no low beam headlights. The brights work

I have no low beam headlights. The brights work though.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

A new head lamp dimmer switch is the remedy for your car

Posted on Apr 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Driver side headlight goes dim on high beam while passenger side is bright


bad connection or bad earth check all connection or bulb

Jan 24, 2016 | Cars & Trucks

1 Answer

Headlights wont work on dim, only bright


Check your head light bulbs, your truck has the dual filiment headlight bulbs one per side which does both high beam and low beam, 9007 bulbs.
If the low beam filiments are burned out only the high beam will work.
Also look into finding out if the headlight switch is gone bad.
The headlight module and or drl module maybe defective.

Jan 24, 2014 | 1996 Ford Ranger SuperCab

1 Answer

2003 Pontiac Grand Am brights work but ONE low beam is out ...


You most likely need a new low beam headlight BULB.It has the low and high beam in it and the separate high beam has only high.
You SHOULD have 2 tabs ,one at each end to pull up and the headlight assembly should then come out easily.
Tapping a blown out headlight can reattach the filament for a short time but after that replacement is necessary.

Mar 12, 2017 | 2003 Pontiac Grand Am

1 Answer

2006 Hyundai Tycson GL Headlight Problems


Could be a defective headlight relay, Located in the fuse block in engine compartment,

Nov 29, 2012 | Cars & Trucks

1 Answer

Replaced the headlights and it seems as though the high beams are not working right. They are on but not right, when you turn on the bright lights should both the low and high beam bulls be on?


Depends on model, most of GM products now have seperate beams for low and high, and some high beams require a different headlight for proper brightness.

Oct 28, 2011 | 2004 GMC Envoy

1 Answer

Have headlight problem 2002 chevy malibu v-6 on the dim side have electria current on both wires to the blub bright beams function normal


if you have power to both headlight plugs for each low and high beam filaments and the ground is good as you say the high beams function normally then you either have bad low beam bulb filaments,poor or dirty connection or you have a daytime running headlight relay on the car and that is the problem with the low beam lights.yes the high beams will work but not low beams if it is the relay.

Mar 04, 2011 | 2002 Chevrolet Malibu

1 Answer

Does this model use a 4 headlight bright system? I have 2 low beam lights but when I put on the bright lights the 2 low beam lights go out and only the 2 bright lights stay on.


I think that many 1990s and even some 1980s GM vehicles with seemingly 4 headlight systems actually use only 2 at a time.

My 1990 Oldsmobile Cutlass Calais, for instance, had 2 high beams that went on independently of the 2 low beam lights when switched with the turn signal lever.

In the 1970s the GM vehicles had 4 headlight systems where all 4 headlights would go on, but they used sealed beams rather than the capsule lights that are used nowadays.

For instance, our 1976 Cadillac Seville has a 4 headlight system that lights up 4 headlights on the high beam mode.

Good luck on seeing at night with the current set up.

Dec 09, 2010 | 1992 GMC Sierra

1 Answer

Low headlights do not work


Check your hi/low beam switch. It sounds like you are not getting power through the switch on low beams.

Dec 29, 2008 | 2000 Isuzu Amigo

1 Answer

My bright light indicater is working, but I don't have any bright lights?


So, when u turn on the high-beams, the indicator light goes on, but u still have low beam headlights only? Check the headlight (either one), and see if by chance both high beams burned out at approx. the same time. U don't specify what year, I'm not sure if u have a replacement bulb, or a sealed beam headlight to replace. If the high beams are both ok, then it must be the headlight high beam switch. Let me know what u find.

Nov 05, 2008 | Honda Accord Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

277 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...