Question about 1989 Mitsubishi Mighty Max

Open Question

MITUBISHI MIGHTY MAX 2.0 WHERE TO SET TIMING MARKS WHEN INSTALLING TIMING BELT

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: how to find timing belts marks toyota rav4 2l

I have just replaced my water pump on my 1998 RAVE4, also, the timing belt and the other two belts. I had a tough time with the timing marks. The way you line these marks up is easy if you take the time, First, if you are changing the timing belt you pull the balancer and both top and bottom plastic covers,(do not try to pull top cover off before you take off balencer and the motor mount off or you will just break it.), Second after covers are removed you will have access to the timing belt, you can now remove it by loosening the tensioner bolt and pushing down on the tensioner wheel, the belt then can be taken off. Third take out number one sparkplug and replace the bottom cover by maybe two bolts so that you can see marks on cover, next replace the balancer and bolt. Turn the motor over by hand with the balancer so the small divit on the back of the balancer is on 0 or top dead center on the compression stroke, you can use a compression gauge for this or I just used a mirror and light to shine in the number one cylinder to see the piston. Next remove the balancer and cover and make sure to make a mark on crankshaft gear and housing. Next you will need mirror and flashlight, now turn camshaft gear clockwise to line the hole in the gear with the top timing mark. I recommend a small circle mirror for this. Now replace the belt. I turned the crank shaft gear one tooth counter clockwise off mark and the camshaft one tooth clock wise off mark so when the belt is on you can turn the camshaft gear counter clockwise to get tension on the belt and marks will line up. I would recommend changing water pump,tensioner wheel, and the idler wheel. After belt is on I would replace the bottom cover the balancer and the crankshaft sensor. Iwould then start it to make sure the water pump is not leaking and the motor is not pinging or you will have to tear it back apart again. Good luck and no I am not a certified mechanic just thought this would be helpful from my own experience.

Posted on Apr 30, 2009

Ad
  • 234 Answers

SOURCE: setting timing marks on a 1998 Ford Escort

think u need a tool it locks the engine at top dead centre then u line cams up

Posted on Jun 07, 2009

  • 1071 Answers

SOURCE: 1991 Mitsubishi Might Max Timing Belt

timing chain when you get a variance in timing easy to see with a timing light haynes manual should be sufficient

Posted on Jul 21, 2009

c17hydro
  • 2984 Answers

SOURCE: 1999 kia sportage timing marks

dfd3ea1.gif Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks
9f1c7ef.gif

  1. Align marks on camshaft pulleys with alignment marks on seal plate.
  2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  3. Loosen tensioner lock bolt.
  4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
  7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
  8. NOTE: Replace tensioner spring if timing belt deflection is excessive.
Timing Belt Installation


eb770f2.gif
  1. Install lower timing belt cover.
  2. Install upper timing belt cover.
  3. Install power steering drive belt and adjust belt tension.
  4. Install fan pulley.
  5. Install generator drive belt and adjust belt tension.
  6. Install A/C drive belt and adjust belt tension.
  7. Install splash guard.
  8. Install fan and fan shroud.
  9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  10. Install fan shroud mounting bolts.
  11. Install fresh air duct.
  12. Connect hose to resonance chamber.
  13. Connect battery negative cable.

Posted on Jul 26, 2009

  • 523 Answers

SOURCE: Torque specs for mighty max

Per my Chilton's manual tehe bolts should be (cold engine) 65 to 72 FT. Pnds., the cam shaft bearing bolts should be 8x25 = 15 - 19 Ft pnds and the 8x65 should be 14 - 15 Ft Pnds.

The sequence is as follows for the (10 ) head bolts:

7 - 5 - 2 - 4 - 10

9 - 3 - 1 - 6 - 8

I hope this may help,
Tom

Posted on Oct 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque for installing the crankshaft for the 2.4 mitymax motor?


Mitsubishi Mighty Max crankshaft bolt Questions & Answers ...

www.fixya.com > ... > crankshaft bolt > Cars & Trucks > Mitsubishi
Mitsubishi Mighty Max cars & trucks crankshaft bolt questions and answers. ...Torque specs for mighty max The head torque specs for 1991 mitsubishi mighty max 2.4 I ... 1989 mitsubishi 2.0 motor crankshaft was turned while timeing belt was off. ...how to install a clutch kit on my 1994 mitsubishi mighty max Disconnect the .

Oct 02, 2015 | Cars & Trucks

2 Answers

94 mitubishi mighty max wont start (no spark)


run fault codes and check for immobiliser , cam/crank position sensor and broken timing belt/chain ( check that the cam shaft is turning). Check ING fuse has not blown

Jun 25, 2014 | Cars & Trucks

1 Answer

How to remove water pump from a 95 Mighty Max


Assuming it has a 3.0 liter V6 engine, you'll need to remove the front of the engine off including the timing belt. If you are to replace the pump, replace the timing belt with tensioner too.

I hope this may have assisted,
Tom

Feb 14, 2011 | 1995 Mitsubishi Mighty Max

1 Answer

I need to replace the timing belt, but i need to see the iming marks locations


Try looking for a sticker on the underside of the hood. If it's a 2.6, it should be 8 degrees BTDC.


Jan 04, 2011 | 1987 Mitsubishi Mighty Max

1 Answer

92 mighty max broke the timing belt got it all back in order valves are ok they open and close fine but now it wont start got fire and gas but no go


the timing belt is not on exact plas mor the timing of theplags are not exact ignition timing for 4 cylinder is 1,3,4,2 for a six sylinder is 1,5,3,6,4,2

Nov 13, 2010 | 1994 Mitsubishi Mighty Max

1 Answer

LOOKING FOR TIMING SPROCKET MARKS ON 1995 MIGHTY MAX?


If it is the 3.0 liter V6 there is a notch in the timing belt crankshaft pulley which aligns with a small mark above in the casting at the 1:00 position or so. As for the cams, each sprocket has a dimple in it which aligns with a vetical mark pressed in to the back steel dust covers.

I hope this may have assited,
Tom

Apr 14, 2010 | 1989 Mitsubishi Mighty Max Macrocab

1 Answer

Need timing mark assistance on timing mark alignment. R2 timing belt.


The timing marks should be available in a Chilton or Haynes manual for that year that you can view or jot down a diagram or buy at one of the local discount auto parts store or Public Library.

Oct 16, 2009 | 1990 Mitsubishi Mighty Max

1 Answer

1991 Mitsubishi Might Max Timing Belt


timing chain when you get a variance in timing easy to see with a timing light haynes manual should be sufficient

Jul 21, 2009 | 1991 Mitsubishi Mighty Max

2 Answers

Engine backfire's when you let off gas but idle's fine


Engines backfire when timing has slipped. You might need a new timing belt. \

Timing belt goes from Crankshaft on bottom of engine to Camshaft on top of engine. Both have to be synchronized to the correct timing.

Check repair manual or internet for correct timing. You'll probably have to find top dead center on first piston.

Jun 12, 2009 | 1988 Mitsubishi Mighty Max

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

457 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...