Question about 1995 Jeep Cherokee

Open Question

The reverse gear in my 1995 grand jeep cherokee doesn't work anymore. it has a 5.2L V8 auto transmission in it. Possible fix or do i have to replace the transmission?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 384 Answers

SOURCE: trying to find the fuse box diagram

check under hood drivers side

Posted on Mar 31, 2009

Ad
  • 52 Answers

SOURCE: 1996 jeep grand cherokee limited v8 5.2, A/C instructions?

  1. Disconnect battery. This must be done to prevent accidental airbag deployment.
  2. Using on A/C recovery unit, remove all R-134a refrigerant from the A/C system. See: Service and Repair
  3. Remove the shift knob by pulling sharply upward.
  4. Place the transfer case in low range. Pry the shift indicator bezel out of the console using a trim stick.
  5. Apply the parking brake and place the transfer case in neutral. Remove the parking brake trim insert. Remove the console attaching screws. Lift the console up and disconnect the 4WD indicator lamp hamess. Remove the console.
  6. Remove the passenger side knee blocker. Remove the single end screw. Remove the screws below the glove box. Remove the screw at the courtesy lamp. Remove the ash receiver and the screws behind it. Remove the instrument panel armature screw behind the ash receiver. Open the glove box and remove the screws behind it. Lower the panel and disconnect the lamp harnesses. For additional instrument panel service procedures to complete steps 6 thru 25, refer to Instrument Panel, Gauges and Warning Indicators/ Instrument Cluster / Carrier/ Service and Repair/ Procedures. See: Instrument Panel, Gauges and Warning Indicators\Instrument Cluster / Carrier\Service and Repair
  7. Remove the pod switch bezels on both sides of the steering column with a trim stick.
  8. Remove the drive side knee blocker. Remove the end screw and screws located at the bottom of the knee blocker.
  9. Remove the cowl top trim panel by prying it up with a trim stick. Remove the solar sensor if equipped.
  10. Remove the "A" post trim panels.
  11. Remove the remove the bolts that attach the lower instrument panel reinforcement to the instrument panel armature and remove the reinforcement.
  12. Disconnect the park lamp switch.
  13. Pull back the carpet at the transmission tunnel from the base of the instrument panel center bezel. Remove the nuts from the upper studs and bolts through the floor that secure the instrument panel center bracket.
  14. Remove the bolts that secure the instrument panel center bracket to the drivers side of the transmission tunnel.
  15. Remove the screws securing the Vehicle Information Center and remove it. Remove the screw fastening the mounting bracket.
  16. Unplug the vacuum harness connector or vent tube on ATC equipped vehicles and the wire harness located under the passenger side of the instrument panel.
  17. Remove the screws holding the passenger side kick panel, along with the screw from the kick panel shroud.
  18. Unplug the antenna cable near the right cowl side panel.
  19. Unplug the instrument panel wire harness connectors from the junction block at the right cowl side panel.
  20. Remove the bolts that secure the instrument panel armature to the windshield fence.
  21. Remove the nuts that secure the top if the instrument panel armature to the windshield fence.
  22. Remove the bolts that secure the ends of the instrument panel to the cowl side panel.
  23. Remove the nuts that secure the steering column to the brake pedal support and lower the steering column.
  24. Remove the bolts that secure the instrument panel armature to the brake pedal support.
  25. Place a protective cover on the seats. Lift the instrument panel off the windshield fence studs and maneuver the instrument panel out and lower it onto the seats.
  26. Disconnect the refrigerant lines from the evaporator tubes. Make sure to install plugs or tape the ends of the lines and fittings to ensure that excessive amounts of moisture do not contaminate the A/C system.
  27. Remove the vacuum line at the tee from the main vacuum supply harness. This line runs through the body with the upper refrigerant line.
  28. Disconnect the heater hoses from the heater core and clamp the ends closed to prevent coolant loss. See: Heater Core\Service and Repair
  29. Remove the coolant overflow bottle.
  30. Remove the Powertrain Control Module with connectors intact and set aside.
  31. Remove the heater A/C housing mounting nuts from the studs on the engine compartment side of the dash.
  32. Remove the heater A/C housing from the vehicle.
  33. To Install the components, reverse the procedure stated above. Torque Specifications: Instrument panel center bracket to floor transmission tunnel fastener: 28 Nm (250 in. lbs.) Instrument panel to windshield fence bolts and nuts: 12 Nm (105 in. lbs.) Instrument panel to cowl side inner panel bolts: 12 Nm (105 in. lbs.) Instrument panel to steering column support bolts: 12 Nm (105 in. lbs.)

Posted on Aug 11, 2009

roman1021
  • 102 Answers

SOURCE: fuse box diagram for 1995 jeep grand cherokee laredo

look on the net that is where i got mine

Posted on Aug 13, 2009

emissionwiz
  • 76132 Answers

SOURCE: location of cam sensor 2003 jeep grand cherokee v8

Answer
pic_12.gif
pic
REMOVAL - 4.7L
The Camshaft Position Sensor (CMP) on the 4.7L V–8 engine is bolted to the front/top of the right cylinder head (CMP Location—4.7L Engine).

It is easier to remove/install sensor from under vehicle.

Raise and support vehicle.
Disconnect electrical connector at CMP sensor (CMP Location—4.7L Engine).
Remove sensor mounting bolt (CMP Location—4.7L Engine).
Carefully twist sensor from cylinder head.
Check condition of sensor o-ring.
See picture for sensor location.


9347d80.gif

Posted on Jul 21, 2010

Testimonial: "that is just what i needed thanks"

  • 2926 Answers

SOURCE: Need a diagram of serpentine

ledsled378_136.jpg
1995 v8

Posted on Jul 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is a 1995 jeep grand cherokee limited v8 vs. inline 6 transmission interchangeable?


No sir they will not interchange. i worked at a transmission shop for 7 years. the inline 6 has a 500 trans in it and the v8 has a 518 trans in it. the bellhousings are different.

Jan 03, 2014 | 1995 Jeep Grand Cherokee

2 Answers

1995 Jeep Grand Cherokee Larado


Take a look inside the changer with the holder removed and clean any contacts you see. There also needs to be the proper amount of electronic lube inside.
Using a CD lens cleaner is also something to try.

I have one '98 GC 5,2L V8 and remember that the first time I put a CD in my changer it read error, even though it was loaded properly. After pulling out and replacing the holder once or twice it played fine.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Nov 05, 2011 | 1995 Jeep Grand Cherokee

1 Answer

Auto Transmission will only go into drive from second gear


It should be an electronic problem Scan the transmission and post the codes

Jul 28, 2010 | 1995 Jeep Grand Cherokee

1 Answer

1995 jeep cherokee coolant line broke we fixed it


Take it back to the shop that fixed it or if you did it yourself, check that you didn't disconnect a sensor/plug from the transmission.
TD

Mar 10, 2010 | 1995 Jeep Grand Cherokee

1 Answer

Jeep was doing ok ,as i came up our mountian i felt two or three small jerks,when i was close to the top it just would not go forward anymore,i tried every gear drive 1st,2nd and reverse,I also tried...


it sounds like your automatic transmission quit his job. How much miles are on the clock? If more than 150.000 and you pulled trailers, climb mountains etc. this will be the first choice. Let the engine idle, push the brakes and check if the car will go in any gear. If this will happen only in reverse gear, your auto trans need to be replaces. You can use a rebuilt auto trans.

Oct 24, 2009 | 1996 Jeep Grand Cherokee

1 Answer

1995 jeep cherokee standard transmission will not go into reverse


If you can select another gear with no grinding and clutch feels normal likely either the reverse synchro is worn out or an internal shift fork is worn...either way, trans needs to come out and be opened up to check. Can you put it into reverse with the engine off?

Jun 27, 2009 | 1995 Jeep Grand Cherokee

2 Answers

1997 grand cherokee limited 4x4 v8


HI, It may seem obvious, but sometimes overlooked.... have you checked the oil level, as low oil can cause some strange things to happen! My 96 4 liter would be reluctant to move sometimes, but after I topped it up, it has been fine.

Apr 28, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Where is the inhibitor switch


yes its on the transmission so you cant stat in drive reverse ect

Aug 19, 2008 | 1995 Jeep Cherokee

Not finding what you are looking for?
1995 Jeep Cherokee Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...