Question about 2002 Daewoo Nubira

1 Answer

Do i need to replace the head bolts on a daewoo matiz after a head gasket refit?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 404 Answers

Not really if the bolts are ok and the thread is fine and not damaged.

Posted on Apr 29, 2010

Testimonial: "good quick answer"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Daewoo matiz oil mixing in water


Most likely a bad head gasket. It could be a cracked head, or a crack in the block. You can check the head gasket by running a compression test. If it's way off between cylinders or if the numbers are down from spec will tell you.

Oct 16, 2015 | Daewoo Cars & Trucks

1 Answer

My daewoo matiz is run off while the temperature is arrived 90 degree, to start i must wait until it will cool or it arrives 45 degree ,it will start by pushing even if it is not cool ,what will be th


Hi there
If your car has a radiator then it is coolant and engine runs at approx 35deg as it works the thermostat witch controls the water flow through the radiator AND your engine is running to hot, OR you have a blown head gasket witch will cause the same problem also check that the radiator isent blocked from the outside [like paper etc] or inside like dirt as some people fill with water from a dam etc.
Let us know how you get on with above.

Oct 27, 2014 | 2005 Daewoo Matiz

1 Answer

Do you know the torque settings for the cylinder head bolts on a w reg daewoo matiz


Tighten the cylinder head bolts to 85--90 NSm (63--66lb-ft).

moz-screenshot-4.jpg1eec8d8.jpg
moz-screenshot-2.jpgmoz-screenshot-3.jpg

Nov 17, 2009 | 1999 Daewoo Lanos

2 Answers

Procedure to replace a clyinder head


YOU NEED A HAYNES REPAIR MANUAL. BECAUSE YOU HAVE A LIST OF THINGS THAT HAS TO BE REMOVED BEFORE REMOVING CYLINDER.YOU NEED TOOLS AND TORQUE WRENCH.

Oct 24, 2009 | 2001 Daewoo Leganza

2 Answers

Daewoo Matiz crankshaft pulley


remove the outer small bolts to remove balancer(pulley) the big centre bolt holds crankshaft gear for timming belt which slides off with timming belt removed.

Sep 10, 2009 | Daewoo Nubira Cars & Trucks

1 Answer

Running problem in monsoon season in Daewoo Matiz.


Has the clutch been replaced recently? There is an earth wire under one of the bell housing bolts,if not refitted can cause all sorts of problems.

Jul 19, 2009 | 2000 Daewoo Lanos

1 Answer

Cylinder head daewoo matiz


Tighten the cylinder head bolts to 85--90 NSm (63--66lb-ft).

29d7267.jpg

Jun 06, 2009 | 1999 Daewoo Lanos

1 Answer

What is the torque pressure for a 01 daewoo matiz 800cc head


2001 daewoo matiz 800cc

This is the best info I have.

Just as important as the torque values is the tightening sequence. Since modern engine heads are soft alloys this is key. The bolts are tighten down maybe half the final value on the first pass and then tighten down fully on the final pass.
The Sequence is; 7 1 3 5 8 4 2 6 bolts 5&6 are the flywheel side of the engine Torque values Stage 1. 40-45Nm first pass Stage 2. 85-90Nm. second pass

Since you have the head removed look for carbon build up on the pistons.
You may want to get a car service manual from the library or on the internet.

May 11, 2009 | 2000 Daewoo Lanos

1 Answer

Air Bag light on in Daewoo Matiz


any auto electrician should be able to plug in and diagnose for you the most probale cause is a bad connection normally on the contacts under the seat if you locate them just discoonect them give them a quick blow clean and refit see if it cures the problem

Dec 11, 2008 | 1999 Daewoo Leganza

Not finding what you are looking for?
2002 Daewoo Nubira Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...