Question about 1996 Acura TL Series

1 Answer

O2 wire got pull out of the oxgen sentor were do they go

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

GET A SCHEMATIC OF 02 SENSOR CIRCUIT. IN MOST CASES YOU WILL HAVE 4 WIRE. 1= 12V FOR HEATER 2= GROUND FOR HEATER 3=REF VOLTAGE FOR SENSOR 4=SIGNAL RETURN TO PCM

Posted on Apr 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace the oxgen sensor for 2002 s10 pickup


might need a special O2 sensor socket to remove, depending on how tight it is. Sometimes you can access it with a wrench

Nov 10, 2016 | 2002 Chevrolet S-10

2 Answers

Fuse for oxygen sensor


I doubt that there is any fuse for oxy sensor. The system computer is connected directly to the sensors, and no fuse is involved.

May 23, 2016 | Cars & Trucks

1 Answer

How do you know if oxgen sensors are bad on a 2008 chevy equinox....had cadillac converter replaced but check engine light still on


to know if a 02 sensor is good is with a scanner with ability of reading pcm data
if you see the data with the freeze frame
o2 sensor are rate 0volts to 1000mv
0 for lean and 1000mv for rich ... 500mv is the neutral below is lean and over 500mv is rich
it switch from rich to poor all the time but with time it will go from400mv to 650 mv poor o2 sensor
or with voltmeter backprobe at o2 sensor the voltage

Oct 07, 2013 | 2008 Chevrolet Equinox

1 Answer

Oxgen sensor on 2006 impla ls


Well if the O2 sensor were faulty, you should get a check engine light and a code for the sensor.
It could be a fuel pressure problem or other issue.

Aug 24, 2012 | 2006 Chevrolet Impala

1 Answer

Where is the o2 sensor on a 93 mighty max


It should be on catalytic convertor to check you oxgen levels in you exhaust.

Oct 12, 2011 | 1993 Mitsubishi Mighty Max

2 Answers

How many oxgen sensors does a 2004 Hyundai Santa Fe 2.7 2wheel drive vehicle have and where are they located? What idoes Bank 2 Sensor 1, Bank 1 Sensor 2, Bank 1 Sensor 1, and Bank 2 Sensor 2 mean?


you have 4 O2 sensors, bank one is the front cylinders ( close to the readiator ) there is 2 bank 1 O2 sensors one infront of the catalitic convertor ( bank 1 sensor 1 ) and one after the convertor ( bank 1 sensor 2 ) the same on the back cylinders they are bank two sensors 1 & 2 i will try to post the location of the wiring plugins if you find the plugs then you can folow the wiring to the sensor....good luck


johnjnail_106.jpg

johnjnail_107.jpg

johnjnail_108.jpg

johnjnail_109.jpg

Jul 01, 2011 | 2004 Hyundai Santa Fe

1 Answer

Will a canister purge vaule throw a oxgen sensor code


No, Each item has its own code more or less. A bad purge valve may give you a warning that the Evap system has a problem and this would include lines, tank, and the fuelcap. Sometimes the Code would be more specific naming the canister purge valve separately without including the lines, tank, or the fuelcap.

But the purge valve and the O2 sensors are completely different systems. The O2 sensors go on the exhaust and the purge valve is grouped with the fueltank. The comparision of the difference is like the purge valve belongs with the fueltank group and the O2 sensors belong with engine controls after the fuel system has finished its job.

I hope my solution is very helpful in explaining how each system is separate.

Jun 01, 2011 | Ford Thunderbird Cars & Trucks

1 Answer

Codes po135


Replace O2 sensor.

Td

Jul 06, 2010 | 1998 Ford Taurus

1 Answer

I fix my camshaft sensor cost $548.00 at dealer they said that po133 code (oxgen sensor) need to be replaced but that code did not pull up on my scanner only p1309 what should i do?


The code po133 means o2 sensor checked slow (response 1/1). You will need to replace the o2 sensor to correct the problem. You can purchase the o2 sensor yourself and replace it at home. It's no big problem in doing it yourself unless you want to take it back to the dealer. Hope this will help.

May 20, 2010 | Cars & Trucks

1 Answer

My engine light is on told it was oxgen sensors is that right


If they connected a scan tool to it and retrieved the error code from the computer and thats what it told them more than likely it is. Depending on what code it threw it could be something causing it to throw O2 code.

Sep 13, 2009 | 2003 Cadillac CTS

Not finding what you are looking for?
1996 Acura TL Series Logo

Related Topics:

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...