Question about 2007 Hyundai Santa Fe Limited

Open Question

Codes PO 464, PO 463, P2068 2007 hyundai santa fe

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 566 Answers

SOURCE: 2007 Hyundai Santa Fe - Replacing fog light

hi have not had pleasure of this on santa fe yet? but will try to help dependant of which side o/s or n/s ? i would first remove the screws holding the front of the under engine plastic cover/shield and drop down sufficient to gain view/access? to the rear of fog lamp then if a cover is on? try turning anti clock to remove? or if rubber cover pull off? then the bulb and clip should be visible? unplug the wire from bulb then the spring clip holding bulb in place normally just sring the 2x top ends together and swing down/clear to remove bulb? refit new bulb correctly! pay attention to position old bulb positioned? then clip securely and re connect wire at this stage it would be best to ensure bulb works ?? before you re assemble all else? wish you luck and hope this helps with your problem ?

Posted on Oct 28, 2008

goalie39
  • 469 Answers

SOURCE: ''check engine light'' illuminated, 1004 Hyundai, Santa Fe

If you live in the US, take it to qany Auto Zone store and thy will read the codes off for you, I would suspect any right thinking competitor would do the same, check if you don't have one near by.

Hope this is of some help.
Ed

Posted on Apr 21, 2009

emissionwiz
  • 75077 Answers

SOURCE: PROGRAM KEYFOB FOR HYUNDAI SANTA FE

This is from the factory service manual of your car:
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote. Translation you need the dealer to do this.

Posted on May 22, 2009

jmgldsmth
  • 1869 Answers

SOURCE: 2007 Hyundai Santa Fe Headlight

you need a torx screwdriver

Posted on May 29, 2009

  • 84 Answers

SOURCE: Change serpentine belt 2004 Hyundai Santa Fe

it uses a spring loaded tensioner.use a breaker bar to rotate the tension and it should just come off.if u need a pic or anything else to do it let me know,

Posted on Oct 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i get a manual for my Hyandia SantaFE???


Lots here. I just read one and do you think I can find it, but it was on page 1.

Here it is

Hyundai Santa Fe Owners Manuals | JustGiveMeTheDamnManual.com



www.justgivemethedamnmanual.com/hyundai/hyundai-santa-fe-owners-manuals






Below you will find free PDF files for select years of your Hyundai Santa Fe automobile. 2003 Hyundai Santa Fe Owners Manuals ยท 2004 Hyundai Santa Fe ...





Hyundai Santafe 2004 Google Search

Mar 17, 2017 | Hyundai Santa Fe Cars & Trucks

1 Answer

2005 hyundai santa fe


This code refers to a misfire on cyl#5. Possible spark plug or ignition coil ( most common ). Could also be an injector or wiring to any of the above

Jul 12, 2015 | 2004 Hyundai Santa Fe

1 Answer

I have a 2011 hyundai santa fe with the check


that code is the intake manifold runner performance try clear the code and see if came back posible a intermitent problem for fordwar diagnostic need to know what you are doing

Oct 07, 2014 | Cars & Trucks

2 Answers

Code po355


the ignition coil on cylinder number 5 secondary circuit malfuncion

Sep 12, 2014 | 2003 Hyundai Santa Fe

1 Answer

Where is the cam sensor located on the 2001 Hyundai Santa Fe


http://www.youtube.com/watch?v=5gwta1NvtsQ


This may help

Feb 28, 2013 | 2001 Hyundai Santa Fe

1 Answer

03 hyundai santa fe po 174 running lean bank 2 .have cleaned massair flow and vhecked for vacume leaks .. no luck


you need to check the 02 sensor for bank 2 to make sure its working properly as if not it will set this code.needs to be checked with a volt meter and should fluctuate between about .2-.3 volts to .7-.8volts and not stuck on one side or the other of .45 volts.

Jul 05, 2011 | Hyundai Santa Fe Cars & Trucks

1 Answer

2002 Hyundai Santa Fe speed sensor replacement, where exactly is it?


P0500 error code on Hyundai sta fe 2004 2.4 L where are the input and output speed sensors located?

Dec 17, 2010 | 2002 Hyundai Santa Fe

1 Answer

I have a Hyundai Santa Fe 2001, 6 cylinders. The


Hi
It sounds like the transmission slipped. You need have the vehicle check for trouble codes and the trans. fluid level.

Steve

Jan 29, 2010 | 2004 Hyundai Santa Fe

1 Answer

What is a 112 and a 444 code on my hyundai santa fe


Code PO 112 is intake air temperature circuit low input and PO 444 is Evaporative Emission control system purge contol valve circuit open. Both codes could be sensor problems or wiring problems.

Mar 11, 2009 | 2001 Hyundai Santa Fe

Not finding what you are looking for?
2007 Hyundai Santa Fe Limited Logo

Related Topics:

1,286 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...