Question about BMW X5 Series

1 Answer

How can i fix the Soft Close in my BMW X5? The back liftgate won't close. No motor noise. When push the lock it make a noise like itdid before. I checked all the related fuses and they were OK.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 31 Answers

Since your car is controled by computers and modules first you have to check the basic. fuses and relays. if they are okay then you may have to go with a pro. tech. to run a scanner.

Posted on Apr 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Cadillac srx power tailgate opens fine, but won't close with the remote. I can't hear the motor. The auto close button doesn't work either. Is there a fuse or relay? If so where is it?


An electronic control module controls it .
The liftgate module (LGM) controls operation of the liftgate latch motor and the liftgate actuator assembly. Do you have a Liftgate Ajar Indicator ON ? Or a message in the message center driver information center (DIC) illuminates the LIFT GATE AJAR indicator ? The liftgate control module could have a DTC - diagnostic trouble code in memory !

When open, the liftgate can be closed by either a keyless entry transmitter or the liftgate close switch. When a GMLAN serial data message or switch input is seen, the liftgate module begins the close sequence. The liftgate motor is reversed, lowering the liftgate until it latches into the liftgate latch. Once latched, the latch will cinch the liftgate to a fully closed position.
Power liftgate function will only be allowed if certain operating criteria are met. Any of the following may cause the power liftgate not to function:
?€¢ Vehicle is not in park. ?€¢ Engine cranking is present. ?€¢ Temperature limits have been exceeded. ?€¢ Liftgate motor overcurrent is detected. ?€¢ Excessive hall effect counts are seen. ?€¢ System voltage is out of range. ?€¢ A DTC is set that disables power liftgate functionality. The liftgate also receives inputs from 2 object detection sensors. If either of these sensors indicate an object is in the path of the liftgate, liftgate functions will be suspended until the object is removed.

Aug 03, 2015 | Cadillac Cars & Trucks

1 Answer

Won't close on own makes banging noise n you have to push roof to close


What kind of car do you have?????????????? But in any event it sounds like the pull down motor gearing is stripped. Hurrah for plastics if it were American made you wouldn't have this problem. (get out your check book)

Feb 16, 2013 | Cars & Trucks

1 Answer

2006 bmw x5 rear seat lock is pull out it looks like it has comb like teeth wont go back in


You just have to be forceful when pushing the seat back and down at same time. It WILL latch in position when you do this.

Nov 26, 2012 | 2009 BMW X5

1 Answer

2004 lincoln navigator ,doors will not open rear hatch will not unlock


The door locks are controlled by the vehicle security module (VSM). It gets power from fuses 30, 5, 6, and 40 in the central junction box (CJB). You say you checked these and all are OK. Therefore the problem must be in the door lock actuators, the door lock relays, or the door lock switches. I doubt that all of these are defective, so the VSM may be defective.

The liftgate is controlled by the power liftgate module (PLM), althogh the motor in the liftgate glass actuator is controlled by the VSM. The PLM gets power from fuses 105 and 5 in the CJB. If the PLM is assumed to be OK, the source of the problem could be the liftgate unlatch motor, the liftgate cinching motor, the L/R liftgate obstacle detection strips, the liftgate home position switch, the liftgate fork bolt/detent switch. or the power liftgate open/close switch

Sep 28, 2012 | 2004 Lincoln Navigator 4x4

1 Answer

Rear liftglass won't lock


#07-08-52-003: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE)/Key Fob Transmitter/Door Lock Switch, Lifgtate Hatch or Liftgate Glass May Lock/Unlock When Rear Liftgate Glass Button Depressed - (Sep 13, 2007)


Subject: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE), Key Fob Transmitter or Door Lock Switch, And/Or Liftgate Hatch Or Liftgate Glass May Lock Then Unlock When Rear Liftgate Glass Button is Depressed (Reposition Lock Cylinder Wave Washer and Adjust Lock Rod)


Models: 2005-2007 Buick Rainier

2005-2008 Chevrolet TrailBlazer, TrailBlazer EXT, TrailBlazer SS

2005-2008 GMC Envoy, Envoy XL, Envoy Denali

2005-2008 Saab 9-7X




--------------------------------------------------------------------------------
Do This
Don't Do This

Reposition liftgate lock cylinder wave washer and adjust lock rod.
DO NOT replace the liftgate latch or actuator.


Condition
Some customers may comment on one or more of the following conditions:

• The rear liftgate glass may not lock when using the remote keyless entry (RKE), key fob transmitter or door lock switch unless the lock is pressed a second time.

• The rear liftgate or glass locks, but may be unlocked when the rear liftgate lock cylinder button is depressed.

• The rear liftgate locks but the liftgate glass may not lock.

Cause
These conditions may be caused by one or all of the following:

• The rear liftgate cylinder lock rod may be out of adjustment.





• The wave washer on the liftgate lock cylinder may be out of position with the cup side down.

• Excessive movement or slack in the lock rods at the liftgate bell crank assembly.





• The liftgate lock cylinder pawl may contact the rear liftgate glass latch when the lock cylinder button is depressed.

Correction
Important: Do Not remove the rear liftgate lock cylinder from the vehicle to perform this repair.

Reposition the rear liftgate lock cylinder wave washer and adjust the lock rod using the steps below.

Verify the customer's condition.

Open the liftgate.

Remove the upper liftgate garnish molding.

Remove the rear liftgate trim panel.

Remove the cylinder lock rod from the threaded lock rod retaining clip.

Tip
Place the tip of a screwdriver blade into the opening of the C-clip and slowly rotate the screwdriver to pry out the C-clip from the shaft. Then use needle-nose pliers to remove the C-clip.

Remove the C-clip from the rear liftgate lock cylinder push button and remove the wave washer.

Install the wave washer with the cup side up.

Position the wave washer with the curved edges of the wave spring parallel to the tabs on the lock cylinder shaft.

Important: Use needle-nose pliers to slightly squeeze the C-clip back into shape. Make sure the clip seated, you should feel a snap and hear an audible click.

Install the C-clip onto the shaft and in the slot using needle nose pliers. Then rotate the pawl several times to make sure the C-clip does not rotate. If the clip rotates then the clip is not fully seated.

Position the lock cylinder pawl to the full clockwise position.

Pull up on the cylinder lock rod to remove any slack in the bell crank.

Install the cylinder lock rod into the threaded lock rod retaining clip while removing any slack from the lock rod linkage.

Close the lock rod retainer clip.

Close the liftgate assembly.

Open the liftgate glass while keeping the liftgate closed.

Use the key fob to cycle the liftgate to the lock and unlock position while inspecting the rear liftgate pawl. The lock cylinder pawl should have clearance between the latch as shown above. If the pawl is contacting the latch, readjust the cylinder lock rod.

Verify that the customer's condition has been corrected.

Install the rear liftgate trim panel.

Install the upper liftgate garnish molding.

Jan 17, 2012 | 2009 Saab 9-7X

3 Answers

The rear lift gate on my 2006 Lincoln Navigator will not open automatically or manually and there appears to be no way to access anything inside the door from inside or out.


POWER LIFT-GATE OPERATION - To open the optional power liftgate, push the button on the instrument panel , press on your five-button key fob (if equipped), or press and release the control located in the left rear quarter panel (Figure B). To unlatch the liftgate glass, push the button ) under the center of the license plate lamp shield, or press on your five-button key fob. Do not open the liftgate or the liftgate glass in a garage or other enclosed area with a low ceiling. Keep clear of the liftgate when operating the rear switch. To open the liftgate manually, pull the handle located on the liftgate to release the liftgate from the vehicle. The power system will take over when you release the handle. To close, make certain the rear window is closed, and then pull down the liftgate a few inches to activate power closing. Closing the gate rapidly or more than a few inches may activate the obstacle detection feature and stop the power system.------------ Also click this link for more help:--- http://technoanswers.blogspot.com/2011/05/power-liftgate-on-will-not-open-on.html ------------ This should help.Keep updated.Thanks.Helpmech.

May 19, 2011 | Lincoln Navigator Cars & Trucks

1 Answer

How do I manually close my 2004 X5 roof


remove the cover where the sunroof switch is and you will see the motor.on the motor is a place to put a 4 or 5 millimeter allen(a allen socket would work best) insert the allen and turn

Feb 04, 2011 | 2005 BMW X5

1 Answer

Subaru liftgate lock stuck, liftgate won't close


You should open the tailgate and pull the handle and at the same time push the hook back so that it is not in the way of the lock bar when go to close it. Sounds like it just got jammed and should be able to be fixed with out having to replace. Assuming that it is not rusted and seized.

Jun 25, 2009 | 2006 Subaru Outback

2 Answers

I have 2001 bmw x5 4.4i, keys wont unlock one back door?


this may be a problem with the actual door lock itself or the general module not sending an open signal to the lock

Dec 30, 2008 | 2001 BMW 5 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

403 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...