Question about 2002 Ford F350 Super Duty DRW Reg. Cab

2 Answers

How to take apart an ambulance?

I just purchased an ambulance truck to use for business purposes, but I really dont need anything inside of it at all. How do I go about taking everything out and dispose it?

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

    Teacher:

    An expert who has written 2 tips or uploaded 1 video tip.

  • Expert
  • 59 Answers

I can give you some suggestions;
First it was used for trauma, use good gloves and protective gear, and bleach, vinegar and other disenfectants as needed.

If you are in a state or locality where vehicle fitness iinspections are done, check with em before continuing.

Then make sure all electrical hot leads are removed or disconnected,
Same with any plumbing and communications hardware,
Then, unbolt and remove all you can with wrenches, some may need to be cut out depending on your needs, if you cut fiberglass wear a respirator, eye and ear protection too. Sawzall's work great with minimal dust, less than say a high speed angle grinder.

Be aware that some inner structure may affect the outer structure of the vehicle, if you remove this replace it with adequate structure suitable for your use.

Local dumps like small pieces, check with your local dump,transfer station, or garbage collection agency before assuming they will or won't take it.

Some of the stuff you remove can be sold, or given away on such sites as craigslist.com and your local freecycle network.

Hope this helps

Posted on Apr 29, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,498 Answers

Hey shakespeare.,

If your in Oregon, get me your address.

I take it you want the cabinetry, and storage inside and out.

First thing, make sure it's been secured of Oxygen Tanks and high voltage inverters.

I'd say in general, get a rivet punch, a hammer,,and a drill for the stubborn ones, a screw gun,with phillips, flat and and assoerrtment of specialty bits, lineman pliers, vise grips and wire cutters, Then go to town...

Get yourself a Sawzall and a box of blades for whatever is left.

Have fun.

Mike,.

Posted on Apr 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does anyone know where the auxiliary battery relay is located on a 2005 Ford E350 Club Wagon. Thanks


if so equipped with one , most only ambulance package has one it's in the under hood fuse box just under the power brake booster , there should be a telltale on inside lid of box to tell you what one it is , they usually only installed this on the ambulance prep package with two alternators , its job was to shut charging ckt power off to aux battery when ign was switched off to prevent loads from draining starting battery

Apr 19, 2015 | Ford E350 Cars & Trucks

1 Answer

Can I paint over this with a water based paint


Don't use a water-based paint for any purpose on a motor vehicle.

It can damage the finish of existing paint, and will NOT stick to the original paint. If this is just a stop-gap measure to cover some imperfection(s), and you don't care about perfection in the result, just purchase a can or two of spray touch-up paint and "have at 'er"!!!

Mar 24, 2015 | Cars & Trucks

1 Answer

Why qr 25 noisy in torque converter


There really isn't anything in a torque converter that could give you noise unless the thing is coming apart inside.(doubtful) What you might be hearing is a bad bearing from the output shaft.These can wear over time.Service for most of the "stuff" down there is replacement.The problem will get worse over time and needs to be seen to by a mechanic.good luck

May 17, 2014 | 2008 Nissan X-Trail

2 Answers

So I have a ford 97 e350 ambulance. I finally got the engine codes they read p0308 and p1662. Showed up at the same time. The truck ran rough, turned engine 9ff, back on, idled fine, and then a few mi utes...


cylinder 8 is missing combustion which caused the o2 code the black box will not cause a specific cylinder to miss, there fore a fuel distribution problem is evident, the injector on eight is proablly the culprit the #8 cylinder is the last cylinder to be fed a fuel, pressure test is needed to determine if the fuel pump is strong enough to deliver diesel, ambulance spend a lot of time idling causing fatigued fuel pumps

Nov 08, 2013 | Cars & Trucks

1 Answer

96 Chev C 3500 454 Gas ambulance. where is the fuel pump located??


The fuel pump should be located in the tank if it is a factory tank. If the ambulance conversion company replaced the tank, you will need to check with them on the pump's location.

Feb 28, 2011 | 1996 Chevrolet C3500

1 Answer

Bought an older 93' forrunner and its said to have a loose valve...? My experience is little and need some help delving into fixing this... do i just start taking it all apart so that i can get the top of...


first thing go buy a repair manual, valves dont come loose they fall into the engine usaully when the engine is running (not good plenty damage) it may just need the valve clearences adjusred if they are not hydraulic . so dont pull anything apart untill you get it diagnosed or you will waste plenty bucks

May 29, 2010 | 1993 Toyota 4Runner

1 Answer

No transission engagement. no d.t.c.in computer


Removed trans? Take it to a trans shop. If you dont know what you are looking at, how do you think you are going to fix it? You should have checked line pressure first before taking trans out. trans shops need to diagnose before they take any trans out.

Feb 06, 2010 | 2003 Ford Windstar

Not finding what you are looking for?
2002 Ford F350 Super Duty DRW Reg. Cab Logo

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...