Question about 1991 Ford Mustang

1 Answer

Hello i have a problem with my 1993 ford mustang convertible top motor. I bought a new motor but when i plugged it in it starts runnin and stays running until i unplug it. Even without the ground wire being connectected. Could it be the top switch is out please help me.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 75 Answers

It sounds like the problem is in the switch or relay. the circuit is not opening when the power is turned off.

Posted on Apr 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1993 Ford Mustang convertible won't go up.But the motor is coming on.Also it will go down thou


There must be a hydraulic fluid leak somewhere. Check to see if there is oil filler cap on your hydraulic pump located in the trunk compartment. Fill if necessary with just enough fluid to raise the top. The reason it won't go up is cause it is lacking pressure from the low fluid

Jun 26, 2012 | 1993 Ford Mustang

1 Answer

Where is the fuse panel on a 1993 ford 4 cly mustang


Hello barbaragarla: My name is Roger and I will help you. You can find the fuse panel located to the left of the steering column under the instrument panel. Should you need further help please just ask. Please rate the answer you received. Thank You for using Fix Ya. Roger

Feb 04, 2011 | 1993 Ford Mustang

1 Answer

1989 5.0 starts but wont stay runnin or idle put hand over intake and fether the gas and you can keepit runnin till you take hand off has new full pump and filter but still no luck


The tuning is for sure wrong the air mixture is not correct and when your hand is placed over it corrects to stabilise.
So i advice you to take a quick test of the tuning /timing.

Sep 28, 2010 | 1989 Ford Mustang

2 Answers

93 mustang convertable quarter windows off track


I'd check to make sure the window regulators are ok,and not damaged.
Tony
www.foxbodyconnection.com

Feb 19, 2010 | 1993 Ford Mustang

1 Answer

What wiring plug engages the torque converter clutch on transmission? My 95 mustang gt 5.0 stalls out when it gets warm but if i put it in first or second gear it stays running.It also has very little...


There are no wires associated with torque converter They work on fluid pressure Your problem with trans will more than likely be linked to lack of power from motor Get your motor tuned would be a good start Hope this helps

Oct 25, 2009 | 1987 Ford Mustang

2 Answers

Convertible top won't go back up, can you help?


IT is probably a fuse. Does it work at all? my mustang had a busted cylinder and only 1 side would go up. If it doesnt work at all then check your fuses. With no manual you will have to use a flashlight and shine on them and see if one is blown. IF they all look good then I would go buy a testlight for about $10 and manually check the fuses for power. It oculd be the motor, however that will cost you several hundred dollars and that is if you install it yourself.

Oct 06, 2009 | 2001 Ford Mustang

1 Answer

Convertible top motor runs for a few seconds and quits. top goes uo about 6 inches but settles back when motor quits. how can i check to see if motor is still good or if needs replacing?


the motor just pumps hydraulic fluid into the lift pistons. If you are low on fluid, the motor can't create enough pressure to run the pistons. Check the fluid level.

1994 info

Section 01-17: Convertible 1994 Mustang. Workshop Manual
ADJUSTMENTS Fluid Level
  1. Remove rear seat. Refer to Section 01-10 .
  1. Carefully remove the rubber fill plug from the back and the reservoir and check the fluid level. The level should be at the bottom of the filler hole. If necessary, add Synthetic Mercon® Multi-Purpose Automatic transmission fluid E6AZ-19582-B or equivalent meeting Ford specification ESR-M2C163-A2. srb~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not overfill or the reservoir seal could be blown out.
  1. Replace fill plug with a new fill plug.
  1. Bleed system as outlined if necessary.

Jul 08, 2009 | 1965 Ford Mustang

1 Answer

Can not find motor mounts for 1986 Ford mustang convertible model .


there are motor mounts and i just bought them for my car the mint go to this wed page www.mustangsunlimited.com they have just about every thing

good luck

Jul 22, 2008 | 1986 Ford Mustang

Not finding what you are looking for?
1991 Ford Mustang Logo

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...