Question about 2001 Pontiac Montana

1 Answer

How do you install a front wheel bearing on a 2001 Pont Montana

How do you install a front wheel bearing on a 2001 Pontiac Montana

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 401 Answers

Jack the vehicle up remove the wheel
remove the brake caliper bottom bolt 15mm. lift the caliper up and slide the caliper pin out
remove the caliper housing bracket 2 - 15mm. bolts
remove the brake rotor
remove the drive axle nut 1 5/16
the remove the hub bearing bolts 3- 13mm. they are in behind (best to use a 13mm flex socket)
disconnect the ABS harness
use a hammer and hit the hub bearing flage (it maybe corroded )
now the hub bearing is out clean the steering knuckle with sandpaper to remove corrosion
install the hub bearing (make sure the ABS harness is in the right position)
and reassemble
hope this helps

Posted on Apr 29, 2010

Testimonial: "Thanks for the very useful information. That was all I needed to get the job done."

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much does a wheel bearing for a 2003 pontiac montana cost?


Again it depends.... anywhere from $100 - $250 depending on front or rear, disk or drum with or without anti lock brakes...

Check out "rockauto.com"... great parts ant great prices...

Jun 03, 2014 | 2001 Pontiac Montana

1 Answer

Need to know clip type for front wheel bearing abs sensor on 2001 montana regular wheel base ?


Not sure what you are actually wanting to know here. I do know that the ads use two types of clips, one is plastic and the other is metal, the only difference that I know of is the price.

Mar 14, 2011 | 2001 Pontiac Montana

1 Answer

The right front tire make a whining sound and when the steering wheel is turned to the left it gets louder.


Sounds like you have a bad wheel bearing. Sometimes you can jack up the wheel, in your case the right front) and with one hand spin the wheel while holding onto the front strut spring with the other. If you can feel the noise (sounds wierd but you can feel the noise) than the bearing is bad. It helps if the transmission is in neutral (make sure you secure the vehicle from moving while its in neutral)

Oct 05, 2010 | 2001 Pontiac Montana

2 Answers

Where wheel speed sensor is located on 2001 pontiac grand am se


2001 Pontiac Grand Am 2.4L SFI DOHC 4cyl

Vehicle Speed Sensor - Location:
The speed sensors are built right into the wheel bearings of your vehicle, at the front and rear locations. They work both with the anti-lock brakes and with the traction control systems on the vehicle.

Removal & Installation
Front
The front wheel speed sensor is part of the hub/bearing assembly. Refer to Wheel Hub and Bearing Replacement in Front Suspension for service procedures.
Rear
The rear wheel speed sensor is part of the hub/bearing assembly. Refer to Wheel Hub and Bearing Replacement in Rear Suspension for service procedures.

I hope help you with this (remember rated this help) Have a nice day, good luck.

Sep 23, 2009 | 2001 Pontiac Grand Am SE

3 Answers

My rear left tire of 2001 Pontiac Montana will not turn


sounds like a bad set of wheel bearings. check them for ware.

Jun 11, 2009 | 2001 Pontiac Montana

2 Answers

2003 Pontiac Montana Front Wheel Bearings


Remove the wheel, remove the hub nut, remove the brake caliper and rotor, put your socket and extension through the hub flange onto the bearing retainer bolts, undo them, release the abs sensor connector if it has it, remove the bearing and hub flange as an assembly, put the new one on and go backwards from here. Torque the hub nut to 180 ft/lbs, your done.

Apr 08, 2009 | 2003 Pontiac Montana

2 Answers

Location of rear heater blower on 2000 pont montana


i got the same van ill take 600 -500$ sk8er724@yahoo.com

Jan 07, 2009 | 2001 Pontiac Montana

1 Answer

2001 pont montana heater blower doesnt work and fuse is ok


Your switch on the dash is faulty, If I turn mine fast on full (5) it doesn't work, slowly turn your switch. Dealer replacement part.

Dec 06, 2008 | 2001 Pontiac Montana

Not finding what you are looking for?
2001 Pontiac Montana Logo

519 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...