Question about 2005 Pontiac Grand Prix

Open Question

Pontiac grand prix GXP monsoon amp wiring diagram

2004-2008 pontiac grand prix GXP monsoon amp and radio wiring diagram

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Radio Wiring Diagram

Go to www.crutchfield.com.

On the bottom of the page there is a link for product support. On the next page, type "2005 Grand Prix" in the search box and hit enter. The top link shows an image and pinout on models with Monsoon sound systems, the second link for ones without.

Hope that helps! Good luck!

Posted on Jun 20, 2008

PyroPCMan
  • 405 Answers

SOURCE: diagram on a pontiac grand prix

Ignition Switch GM Century/Lumina/Grand Prix/Intrigue 1997-2000 The vehicles covered by this guide use one of two types of ignition switches:

  • A mechanical key and lock cylinder built into the steering column, that works a pull rod to actuate the separate electrical portion of the ignition switch mounted further down the steering column. For more information and replacement procedures on this type of switch, please see .
  • An instrument panel-mounted ignition switch is also used on some W-Body vehicles. To service this switch, the radio, heater & A/C control panel and the instrument cluster must be removed. All of these procedures are found elsewhere in this section.
REMOVAL & INSTALLATION
Instrument Panel-Mounted Ignition Switch
WARNING You must perform the Body Control Module (BCM) theft deterrent relearn procedure after replacement of the ignition lock cylinder. Failure to perform this relearn procedure means the BCM will not function properly. This means the vehicle will not be theft protected by the Passlock system and the engine may not crank or start. GM recommends that this procedure be performed with their Tech 2® or equivalent scan tool. An alternate relearn procedure is given at the end of this procedure.
  1. Disconnect the negative battery cable.
  2. Remove the radio assembly following the procedures found in this section.
  3. Remove the heater & A/C control head assembly following the procedures found in this section.
  4. Remove the instrument cluster assembly following the procedures found in this section.
  5. Detach the electrical connectors from the ignition switch.
  6. Insert the key and turn the ignition switch lock cylinder to the ACC position.
  7. Depress the transaxle park/lock cable retainer to release, then pull to remove the cable from the ignition switch.
NOTE You must perform the Body Control Module theft deterrent relearn procedure after replacement of the ignition lock cylinder.
  1. If it is necessary to remove the ignition lock cylinder from the ignition switch (theft damage, etc.), use the following procedure:
    1. Insert the key and turn the ignition switch lock cylinder to the ON position.
    2. Using a small flat-bladed tool, depress and hold the lock cylinder retaining tab.
    3. Using the key as an aid, pull to remove the ignition switch lock cylinder from the switch.
    4. Remove the key from the lock cylinder.
    5. Carefully pull to release the ignition switch bezel from the ignition switch lock cylinder.
  2. Remove the ignition switch bracket bolts and remove the ignition switch through the instrument panel cluster opening.
  3. Remove the bolts retaining the ignition switch to the bracket and remove the bracket.
0900c15280090fea.jpgRemoving an instrument panel-mounted ignition switch assembly—1998 Oldsmobile Intrigue shown, others similar To install:
  1. Install the ignition switch to its bracket and install the bolts. Install the ignition switch into position through the instrument panel cluster opening and install the bracket retaining bolts.
  2. If removed, install the ignition switch lock cylinder to the ignition switch using the following procedure:
    1. Recode the lock cylinder, if necessary.
    2. Align the ignition switch bezel to the tabs on the ignition switch lock cylinder and carefully press to secure in place.
    3. Insert the key and turn the ignition switch lock cylinder to the ON position.
    4. Align the ignition switch lock cylinder to the ignition switch, then press into place.
  3. Turn the key to the ACC position. Align and press into place the transaxle park/lock cable to the ignition switch. Remove the key from the switch.
  4. Attach the electrical connectors to the ignition switch.
  5. Install the instrument cluster using the procedures found in this section.
  6. Install the heater & A/C control panel using the procedures found in this section.
  7. Install the radio assembly using the procedures found in this section.
  8. Connect the negative battery cable.
  9. If the lock cylinder was removed, perform the BCM Programming/RPO Configuration procedure.
THEFT DETERENT RE-LEARN—WITHOUT TECH 1®SCAN TOOL
This procedure takes approximately 30 minutes. Make sure the battery is fully charged before proceeding.
  1. Turn the ignition switch to the OFF position.
  2. Turn the ignition switch all the way from the OFF to the START position, then leave it in the ON position. The engine will not crank.
  3. The SECURITY light should come on and stay on for at lease ten minutes.
  4. Turn the ignition switch to the OFF position for five seconds.
  5. Repeat Steps 2, 3 and 4 again for a second time.
  6. Repeat Steps 2, 3 and 4 again for a third time.
  7. Turn the ignition switch to the OFF position.
  8. Turn the ignition switch all the way to the START position. The engine should now start.

Posted on Sep 09, 2008

bunnydawg
  • 5158 Answers

SOURCE: 2004 pontiac grand prix serpentine belt replacement/ routing

first look underneath the hood... is it there on a sticker... if not i'll need the size of the motor to let you know

Robert

Posted on Jan 27, 2009

  • 1 Answer

SOURCE: LOOKING FOR A FUSE BOX DIAGRAM FOR 2004 PONTIAC GRAND PRIX GT

It's under the hood, on the driver's side, under a square, black box with a lightning symbol on it. Loosen the flower-shaped screw that holds the lid of the box down, remove the lid, flip it upside down and when you look at the inside of the lid, you'll see a map of all your car's fuses. There's also a fuse diagram on the very end of the dash, but it's accessible only when you open the driver's side door. When you're driving, that end of the dash is blocked by the closed door.

Posted on Jul 01, 2009

  • 92 Answers

SOURCE: 2004 PONTIAC GRAND PRIX FUSE BOX DIAGRAM

The diagram is on the fuse box cover or lid (depending on which fusebox, cabin or engine compartment. The diagram is also in the owner's manual.

Posted on Feb 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I disconnect the amplifier on my 2005 Grand Prix; it makes continuous static noise whether the radio is on or off or whether the ignition is on or off?


Assuming it's the monsoon amplifier it's located under the rear deck about 8 inches away from the passenger rear speaker. However unplugging it will kill all the speakers. The only way to properly bypass it is to run all new wires.
You maybe able to find another factory amp at a salvage yard.  

Warning: Most of the Monsoon head units have a 6V offset, making it incompatible with aftermarket amps.

Feb 28, 2015 | 2005 Pontiac Grand Prix

1 Answer

1997 grand prix 4 door radio wiring diagram


Go to your local dealership repair shop. They can scan a copy for you. It will make it all very easy when you have the wire colors and circuit description.

Jul 22, 2012 | Cars & Trucks

1 Answer

Both power outlets in my 2007 Pontiac Grand Prix do not work. HELP


Unless you can use a volt meter at some skill level
& better yet follow the wires & even have a wiring diagram

Then you need help
Not from the internet,we don't have the
car to test things

A handy friend or a repair shop

Jun 08, 2012 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

Looking for diagram on how to replace a water pump in 2007 pontiac grand prix


library sec629 has mitchell and chilton--online also-------at parts store haynes book

Oct 12, 2011 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

Can I change the battery in my pontiac grand prix gxp without going to the dealer


of course you can but make sure you have the radio code written on the back of the sun visor before you start

Jul 31, 2011 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

Need radio wiring diagram for 2000 pontiac grand prix factory diagram


2000 Pontiac Grand Prix Car Stereo Wiring Guide
Car Radio Battery Constant 12v+ Wire: Orange
Car Radio Accessory Switched 12v+ Wire: Yellow
Car Radio Ground Wire: Black
Car Radio Illumination Wire: Brown
Car Stereo Dimmer Wire: Gray
Car Stereo Antenna Trigger Wire: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: Dash
Left Front Speaker Positive Wire (+): Tan
Left Front Speaker Negative Wire (-): Gray
Right Front Speaker Positive Wire (+): Light Green
Right Front Speaker Negative Wire (-): Dark Green
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: Rear Deck
Left Rear Speaker Positive Wire (+): Brown
Left Rear Speaker Negative Wire (-): Yellow
Right Rear Speaker Positive Wire (+): Dark Blue
Right Rear Speaker Negative Wire (-): Light Blue

Sep 17, 2009 | 2000 Pontiac Grand Prix

2 Answers

CB Radio in a 2007 Pontaic Grand Prix


Easy to hardwire. Run the ground wire to anything metal under the dash, the power wire can be tapped into any fuse in the fusebox with a small adaptor available at any auto supply store.

Jul 02, 2009 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

Need a diagram of the 2007 pontiac grand prix belt system.....


try these websites to see if you can find anything on your car drive belt diagram its www.webcrawler.com and the other one is www.alldatadiy.com also try www.autozone.com and for the most part there is a diagram under the hood showing you how the belt goes

Jun 09, 2009 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

Aux input location


Though I'm sure there is an AUX button on the radio, there isn't actually an auxillary port on a 2007 Grand Prix stock radio.I'm sorry to say, but you would have to get an aftermarket radio.

Mar 11, 2009 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

Radio Wiring Diagram


Go to www.crutchfield.com.

On the bottom of the page there is a link for product support. On the next page, type "2005 Grand Prix" in the search box and hit enter. The top link shows an image and pinout on models with Monsoon sound systems, the second link for ones without.

Hope that helps! Good luck!

Jun 13, 2008 | 2005 Pontiac Grand Prix

Not finding what you are looking for?
2005 Pontiac Grand Prix Logo

Related Topics:

2,253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...