Question about BMW X3 Series

1 Answer

How to remove rear window from the regulator 2006 x3

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 462 Answers

As far as I remember it has one bolt holding glass to the window reg. with plastic bushings .
if you have door penal removed , pull out(carefully , don't tear it apart) isolation , lower the window and you wll see it.

Posted on Apr 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 bmw x3 3.0i timing chain or belt


BMW, 3.0i has two Timing Chains. Primary Timing Chain can be
reached by removing the Harmonic Balancer. Lower Timing Case Cover. Vanos Adjusting Unit. Secondary timing chain replacement will require removal of several components and Vanos Adjusting Unit.

Mar 16, 2015 | 2006 BMW X3 X3 4dr AWD 3.0i

1 Answer

2006 BMW X3 rear passenger side window not working


ok i think cable that operate the gears to the window broke

Dec 16, 2013 | 2006 BMW - X3-Series

1 Answer

Passenger back window will not roll up


If you can hear the motor running and the window does not move than the wire in the regulator has probably broken. The rear door panel will need to be removed to access the regulator. Regulators are pretty common and should be in stock at just about any good parts store. I like the Dorman brand of aftermarket regulators and have also has good luck with the NAPA brand as well.

Aug 13, 2012 | 2006 Hummer H2

1 Answer

How to change fuel filter catrige and micro filter on BMW X3


IF YOU HAVE FUEL FILTER WITH FUEL PUMP ASSEMBLY YOU HAVE TO REPLACE FUEL PUMP ASSEMBLY REMOVE THE REAR SEAT BENCH IN ORDER TO REPLACE THE FUEL PUMP ASSEMBLY. NOW IF YOU HAVE FUEL PRESSURE REGULATOR AND FUEL FILTER AS ONE UNIT.BECAUSE FUEL PRESSURE REGULATOR BUILT TO THE FUEL FILTER.TO REPLACE FUEL FILTER, FIRST DEPRESSURIZE THE FUEL SYSTEM BY REMOVING THE FUEL PUMP RELAY LOCATED ON THE COWL.THEN CRANK ENGINE UNTIL IT DIES LACK OF FUEL.THE CRANK ENGINE OVER FEW TIMES TO MAKE SURE ALL FUEL OUT THE FUEL LINES.LOCATION OF FUEL FILTER UNDER THE VECHICLE MOUNTED TO THE LEFT SIDE OF THE CHASIS.

Jul 12, 2011 | 2009 BMW X3

1 Answer

The left rear door window fell off the track. How do I remove the door panel to access it.


This is the complete procedure you stop when you see the problem.



1. REMOVE REAR DOOR INSIDE HANDLE BEZEL


(a) Remove the screw.


(b) Using a screwdriver with its tip taped, disengage the 2 claws A.


(c) Pull out the the rear door inside handle bezel in the direction indicated by the arrow, disengage the claw B, and remove the rear door inside handle bezel.


2. REMOVE DOOR PULL HANDLE


(a) Using a screwdriver wrapped with the protective tape, disengage the 2 clips and remove the door pull handle.


3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


(a) Remove the screw.


(b) Disengage the 7 clips.


(c) Disconnect the connector and pull up on the rear door trim board sub-assembly to remove it.


4. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


(a) Remove the bolt.


(b) Disengage the 2 claws and separate the rear door inside handle sub-assembly.


(c) Disconnect the 2 cables and remove the rear door inside handle sub-assembly.


5. REMOVE REAR SPEAKER


6. REMOVE REAR DOOR SERVICE HOLE COVER


(a) Disconnect each connector and remove the rear door service hole cover.


HINT:


Remove the remaining tape on the door side.


7. REMOVE REAR DOOR GLASS RUN


(a) Connect the window regulator switch assembly.


(b) Fully lower the door glass.


(c) Remove the rear door glass run.


8. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


(a) Remove the 2 bolts, the screw and rear door window division bar sub-assembly.


9. REMOVE REAR DOOR QUARTER WINDOW GLASS


(a) Pull out the direction indicated by the arrow, remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit.


10. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP


11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


(a) Remove the rear door glass sub-assembly as shown in the illustration.


(b) Disconnect the window regulator switch assembly.


12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


(a) Disconnect the connector.


(b) Loosen the temporary bolt.


NOTICE:


If the temporary bolt is removed, the rear door window regulator may fall and become deformed.


(c) Remove the 3 bolts and the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.


(d) Remove the temporary bolt from the regulator.


13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY REAR


(a) Using a "torx" driver (T25), remove the 3 screws and power window regulator motor assembly rear.


14. REMOVE REAR DOOR LOCK ASSEMBLY


(a) Disconnect the connector.


(b) Remove the bolt.


(c) Using a "torx" socket wrench (T30), remove the 3 screws.


(d) Slide the rear door lock assembly downward, pull out the link from the outside handle frame, and remove the rear door lock assembly and cables as a unit.


(e) Remove the door wire harness packing.


(a) Using a "torx" socket wrench (T30), loosen the screw.


(b) Disengage the 2 claws and remove the rear door outside handle cover.


(a) Disengage the 2 claws and remove the rear door outside handle pad rear.

Jan 03, 2011 | 2006 Toyota Highlander

1 Answer

Window dropped into rear door panel. How do I remove the panel & repair


the window regulator has failed. the door panel has to be removed first which requires removing the trim piece that is on the grab handle (extremely hard to remove without breaking) there are three of four screws that hold the door panel on. once the door panel is off, the vapor barrier has to be removed. don't tear it, it is there for a reason to keep water out of the vehicle. make sure you reseal it properly with window weld. once the vapor barrier is removed you will need to unclip the window glass from the regulator. i typically will take and break the tab that holds the window. once the window is loose, move the glass all the way to the top of the door. now remove the regulator, swap the motor over, and reassembly. i would recommend taking the vehicle to a bmw dealership, around $650 for the complete repair and the dealership will stand behind their repairs

Apr 18, 2009 | 2004 BMW 3 Series

1 Answer

How do you remove a rear window motor on a 1997 f-250 crew cab?


You will need to remove the regulator which is the device the rolls the window up and down. This will be riveted on which is best but could be bolted back. Once you have this out you can remove the motor from the regulator and replace. Becare ful if it has a spring on the regulator you want to put the regulator in a vise so it will not get you.

Feb 26, 2009 | 2006 Ford F-250 Super Duty

3 Answers

Hey when i push the power botton for the rear window it doesn't go down,I checked the power button,and its good ! Can i replace the power motor in the rear window,and where is it located,i would like to...


  1. Raise and support the rear door window glass to the full up position.
  2. Remove the interior door handle.
  3. Remove the rear door speaker.
  4. Remove the water shield.
  5. Disconnect the rear door window regulator motor electrical connector.
  6. Remove the rear door window regulator rivets.
  7. Remove the rear door window regulator by sliding the regulator arms off of the window glass track.
  8. Installation is the reverse of the removal procedure, noting the following:
    • Cycle the door glass to make sure of engagement of the drive mechanism.
    • Remove the rear door window glass-to-regulator bolt or rivet.
    • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet.
    • Secure the rear door window glass in the full UP position with tape.
    • Disconnect the window regulator motor electrical connector.
    • Remove the 2 window regulator nuts.
    • Remove the 3 window regulator motor bracket nuts.
    • Install the window regulator assembly. Tighten the 3 motor bracket nuts to 89 inch lbs. (10 Nm).
    • Install the 2 window regulator nuts. Tighten the nuts to 89 inch lbs. (10 Nm).
    • Connect the window regulator motor electrical connector.
    • Remove the tape securing the rear door window glass in the full UP position.
    • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet. Tighten the bolt to 62 inch lbs. (7 Nm), or install a new rivet.
    • Install the window regulator motor
    • Remove the window regulator assembly.
Remove the window regulator motor

Feb 23, 2009 | 2001 Ford Explorer

1 Answer

Rear passenger side window stuck in down position


1) Yes you are right to think that it is the regulator.
2) You can repair this.

Remove the screws that hold the door panel on.
Remove the door panel. There are alot of clips on the door panel that just need to be pulled out with panel while removing.
Remove debris shield.(plastic piece between door panel and door.
The regulator will be visible at this point.
Disconnect the electrical connector from the regulator. Separate Glass from regulator. Some use clips some use bolts to hold the glass to the regulator.
Remove regulator attaching bolts.

Thats it just reverse the procedure for installation.

Aug 29, 2008 | 2006 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Anthony Jones
Anthony Jones

Level 2 Expert

128 Answers

Frankie B

Level 2 Expert

65 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...