Question about 1998 Isuzu Rodeo

1 Answer

I took my rodeo to the shop to have cv axle

I took my 92 rodeo to the shop to have cv axle change, they spent 6hrs and could not get it out, is there a pin or something holding it in?

Posted by on

1 Answer

Go to a trans shop

Posted on Apr 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get the CV axle for a 1998 Isuzu rodeo


THERE ARE PLENTY AVAILABLE FROM SCRAP YARDS, AND E-BAY. THE RODEO HAD PROBLEMS WITH THE TRANSMISSION.

Jun 20, 2015 | 1998 Isuzu Rodeo

1 Answer

Isuzu rodeo troubleshooting


Sounds like a ball joint seeing that the cv joints were replaced, have you had it aligned?

May 07, 2014 | 1998 Isuzu Rodeo

1 Answer

How to replace passenger cv joint 94 intrepid


as for your cv boot you will find you are cost ahead to replace cv axle . if you replace only the boot you have no warranty if you replace whole axle you have warranty not a hard job if you know how

Jan 10, 2013 | 1994 Dodge Intrepid

1 Answer

Im replacin the cv joints on passanger side and driver side how do i get the axle out of the transmission casing is ther a key behind the plate with the 4 bolts? my truck is a 99 isuzu rodeo LS 4wd


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Apr 20, 2011 | 1999 Isuzu Rodeo

1 Answer

1996 Toyota Camry LE. Took it to the shop to have the CV joints replaced, both of them. Mechanics are unable to get either side axles out of the transmission. They have tried using heat, impact hammer,...


There is a small "circlip"holding the axle in place. Place a pry bar between the cv joint and the transmission and pry the axle out with a sharp snapping movement. This should pop the axle loose from the "circlip". The steering wheel can be turned to gain more working room. Tell those guys to lay off the heat. Hopefully no damage was done and they will be able to get the new axles in without too much trouble. Merry Christmas.

Dec 24, 2010 | 1994 Toyota Camry

1 Answer

I have a 1999 isuzu 4wd rodeo 6 cylinder and was wondering if Need to install a new boot kit or if I need to replace the entire front left cv axle shaft. I had a tear in my rubber boot and noted some...


Do not try to get the cv axle out ot the axle housing. It is a major operation. Remove boot and disconnect the inner cv joint and save about five hours of time. The choice is yours ,boot or reman cv axle. You will need to take the reman. axle apart to install it though and some new clamps. Not a simple operation.

Sep 28, 2009 | 1997 Isuzu Rodeo

1 Answer

Cv joint removal


Get the replacement cv axle and remove inner boot and clip and bearings. Do the same on the old axle. Replace bearing clip, cv shaft and reassemble. Do not try to remove the part from inside the front axle unless you want to spend about six hours of time and money.

May 12, 2009 | 1999 Isuzu Rodeo

1 Answer

1994 cv axle


please go to an auto parts store and buy the auto manual for this car.its not that hard to do.and be careful

Apr 09, 2009 | 2001 Isuzu Rodeo

2 Answers

Having problem pulling cv axle


from the front? If so no there is no easy way to do so. I had to drop the differental and then remove the cv shaft.... but this was on a 1993 I would think its still the same...

Feb 09, 2009 | 2001 Isuzu Rodeo

2 Answers

97 toyota celica outer cv boot replacement passenger side


have you undone the main hub bolt, if yes, there could be two different items holding the cv joint on, one is a small circlip in the joint end, or the other is just like an expanding metal ring again only small. what i had to do to change my one was take the driveshaft out (easier to see whats there) then gently (rubber hammer) hit the CV joint it should then fall off to allow you to change the CV joint. I spent over an hour trying to get the metal ring off, then after taking driveshaft off it was changed and back on in ten mins. Or you can go to a motor factors or similar and get a boot puller, my opinion hammer works better lol

Jan 25, 2009 | 1997 Toyota Celica

Not finding what you are looking for?
1998 Isuzu Rodeo Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...