Question about 1995 Chrysler Cirrus

Open Question

95 Chrysler Cirrus driver side front seat will not move front or back. The seat is all the way back and is over the rear bolts to the seat. How do I get the seat to move out of the way?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ga_drifter
  • 36 Answers

SOURCE: 2004 chrysler sebring.The driver side rear door electric window

you have a bad window regulator assembly

Posted on Jan 30, 2009

Ad
  • 4 Answers

SOURCE: 2005 Chrysler Pacifica passenger doors have no power

If your alarm went off, it could be that someone had tried to break into your car. They most likely may have cut some of the wires inside your door with what ever device they may have been using. Look for evidence between the bottom of the windows and doors where the problem is. If not, then it is possible that your automatic window assemblies are malfunctioning. Do you hear the motors run on the windows when you go up or down with the switch? I also have a Pacifica, 2005, however no window problems yet.

Good Luck,

Ray

Posted on May 11, 2009

  • 39 Answers

SOURCE: Where is coolant drain plug on 1996 Chrysler Cirrus?

The coolant drain plug is located on the bottom left side of the radiator when looking from front of car. To access it you must remove the passenger side fog light and push the rubber cover out of the way.

Posted on Jun 23, 2009

  • 3 Answers

SOURCE: Picture of 1999 Chrysler Cirrus rear disc parking

Parking brake is operated by a cable and not the caliper. Your car has disc brake pads for squeezing the rotor to stop, the parking brake has drum type brake shoes that push out on the inside of the rotor. Changing the disc pads only requires squeezing the piston back in like usual.

Posted on Dec 17, 2009

Danniboi
  • 1098 Answers

SOURCE: The heated seats for the front driver and passenger don't work

yes maybe a fuse, also look under the seat and ensure the wire is connected they sometimes get caught when moving the seat back and forward and split against the metal seat base.

Posted on Jan 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing front passenger seat


Move the seat all the way to the rear to access the front two bolts, then move the seat all the way to the front to access the rear two bolts. Don't forget to unplug any electrical connectors before removing the seat as to avoid damaging connectors or wiring.

Jun 22, 2016 | Chrysler Sebring Cars & Trucks

1 Answer

Removing driver side door panel on 95 cirrus


This is basically the same for a cirrus

May 21, 2014 | 2000 Chrysler Cirrus

1 Answer

Right rear brakes keeps messing up on a 1998 Chrysler Cirrus, we keep buying new right rear brakes about every two months or less. Can you help us out?


You have to make sure the brake system is operating properly.Change both rear brakes it sounds like the left rear brake side is not working making the right side wear out so quick.After changing the back brakes bleed them making sure you have no air in your brake lines.start bleeding them from the left rear to the right rear to the left front to right front to master cylinder.

Apr 02, 2014 | 1998 Chrysler Cirrus

1 Answer

Front seat removal pt cruiser


If you move the seats all the way back you should be able to get at the front two bolts on each seat. If you move the seats all the way forward you should be able to get at the rear two bolts on each seat. Once the bolts are removed unplug all the harness under the seats and remove the seats from the vehicle.

Mar 09, 2012 | 2002 Chrysler PT Cruiser

3 Answers

How do i take the back off on a 1999 nissan maxima bucket seat


Hi, follow the instruction below......
Rear
See Figures 3, 4, 5 and 6
  1. Remove the lower seat cushion by pulling straight up on the front portion and disengaging the clips. Then hinge the seat upward to release the rear clips.
03b6e0a.jpg

Fig. 3: Pull up on the front of the lower seat cushion and disengage the clips
  1. Remove upper rear seat back-to-chassis bolts.
77eb191.jpg

Fig. 4: Remove the bolts behind the center armrest ...

a796228.jpg

Fig. 5: ... and the bolts on the lower corners ...

fbf100a.jpg

Fig. 6: ... Then pull up on the seat to disengage the three clips on the top of the seat
  1. Remove rear seat back by tilting forward and pulling straight up.

To install:
  1. Install the lower seat cushion and torque the lower rear seat-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm).
  2. Install the upper rear seat back cushion and torque the upper rear seat back-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm)

Jan 19, 2011 | 1999 Nissan Maxima

1 Answer

1996 Chrysler cirrus has rear seat belt that won't unlock


You may have something in the retracter for the seat belt so you will have to acces it and take a look to see what is in there.

Feb 07, 2010 | 1996 Chrysler Cirrus

1 Answer

How do you install a fuel pump on a 99 chrysler cirrus


fuel pump is under the rear seat on right side in fuel tank you have to remove seat

Jul 30, 2009 | 1999 Chrysler Cirrus

1 Answer

Back struts.


Should have to take off the bolt on the bottom of the strut, and the strut mounts on the top. Most likely get them through the trunk.

Mar 18, 2009 | 1995 Chrysler Cirrus

1 Answer

I need to replace the front driver's seat in a 95 saturn...


seat frame base is held to floor with four bolts, one in each corner.  Begin by moving seat to the full forward position, remove the two rear seat frame bolts, they may be covered by carpet and plastic trim.  Them move seat to full rear position and remove both front frame bolts, the seat will now be free to remove.  Keep me posted

Jan 06, 2009 | 1995 Saturn Sl

Not finding what you are looking for?
1995 Chrysler Cirrus Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...