Question about Mercedes-Benz 560-Series

1 Answer

Need torque setting for lock nut in rear of hub please

Posted by on

  • iancapewell Apr 29, 2010

    thanks will try now,

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,489 Answers

Great car!! Should be around 225 ft lbs. Let me know if you need anything else.

Posted on Apr 28, 2010

  • Kori Policy
    Kori Policy Apr 29, 2010

    Let me make sure that you are refering to the axle nut or something different?!

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear hub torque setting


If you mean the bolts that hold the back-plate, tighten to 35 ftlbs. If you mean the hub nut that hold the bearing assembly, tighten till firm, then back off the nut and tighten till there is no play in the bearing assembly. Do this with the wheel on. Now use the ca adjustment. Put the cap on and you are done.ge and split pin to hold the

Mar 31, 2014 | 1996 Volkswagen Golf

1 Answer

Torque specs bearing


Honestly you should search google. It is right there. the inner hub nut must be torqued to 59 Nm rotate the hub three times in each direction and then loosen the inner hub nut until it can be turned by hand, then again tighten the inner hub nut to 25 Nm. the lockwasher against the inner hub nut, it only goes in one way, it has a small inner tab that locates with the key way of the hub, this is between the threads. Once the lock washer is in the correct position, you can now install the outer hub nut, this outer nut must be torqued to 47 Nm, once you have tightened this outer nut, please once again check that the starting effort is correct.

Oct 18, 2013 | 2007 Toyota Hilux 2.5

2 Answers

Torque on the rear spindle nut of a 1992 mercury cuogar


there is no torque you turn the nut till its thigh than back it off 1/4 turn put the cotterpin in and then the cap

Apr 24, 2011 | 1992 Mercury Cougar

1 Answer

We replaced the hub bearing and want to know the tork setting for the hub nut that holds the cv shaft through the hub? Please


The nut should be a conical locking style nut. 90 foot pounds is normal torque setting if it is a non self lock nut. Locking nuts are installed till fully seated

Feb 27, 2011 | Mercury Sable Cars & Trucks

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd


4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal
      06017-esca-g94.gif

      Inner wheel bearing removal-rear hub/bearing
      06017-esca-g95.gif

      Rear wheel bearing removal-2wd
      06017-esca-g96.gif

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable
    06017-esca-g97.gif

    Rear wheel bearing installation
    06017-esca-g98.gif
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

1 Answer

Rear wheel hub torque settings


spindle hub bolts 75-110 ft lbs.

rear spindle lock nut 130-173 ft lbs.

lug nuts 65-87 ft lbs.

Oct 08, 2010 | 2004 Mazda 6

1 Answer

What are the torque settings for landcruiser hub and axle assembly


This is for the hub....front hub:

  1. Install the hub with a new gasket and tighten the mounting nuts to 23 ft. lbs. (31 Nm).
  2. Install the bolt and washer and tighten it to 13 ft. lbs. (18 Nm).
  3. Coat the inner hub splines with grease.
  4. Make sure the control handle on the cover is still at FREE (if not automatic), position a new gasket in the cover and install the cover so that the pawl tabs are lines up with the non-toothed portions of the hub body. Tighten the mounting nuts to 7 ft. lbs. (10 Nm).
This is for the rear hub:

To install:
  1. Place the hub on the axle housing and install the outer bearing.
  2. Install the lock plate with the lock plate tab positioned into the groove of the axle housing.
  3. Install and tighten the adjusting nut with the special tool used during removal.
  4. Torque the nut to 43 ft. lbs. (59 Nm). Rotate the hub a few times and retorque the adjusting nut to 43 ft. lbs. (59 Nm).
  5. Loosen the adjusting nut until the hub can be turned by hand.
  6. Tighten the nut a small amount and check the amount of pressure required to rotate the hub using a spring tension gauge.
  7. The recommended rotational torque is 5.7-12.6 lbs. (1984-88: 0.9-7.3 lbs.). Tighten or loosen the adjusting nut as required to obtain this reading.
  8. Align one of the axle housing slots with one of the adjusting nut slots. Install the lock screws into the holes of the adjusting nut which are at right angles to the aligned slots. Torque the lock screws to 35-60 inch lbs.
  9. Recheck the rational torque and install the axle shaft using a new gasket.
  10. Install the wheels and lower the vehicle.

Next post is for axles.

Aug 07, 2010 | 1986 Toyota Land Cruiser

1 Answer

Need the 2000 Buick LeSabre rear wheel Hub nut torque spec.


Those are not nuts, they are bolts. The torque spec for those bolts is 52ft.lbs

Jul 12, 2009 | 2000 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76673 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...