Question about 2000 Mazda 626

Open Question

How do I remove the alternator? what belt do I remove?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to remove alternator belt to get the alternator out


It looks like you have one belt for all accessories. There should be a belt tensioner that keeps the belt tight. You move the tensioner to release tension on the belt, then remove the belt from the alternator pulley.

Jan 17, 2014 | 2007 Hyundai Santa Fe Limited

1 Answer

How to replace the power steering belt on a 4g13



ADJUSTMENT

Excessive belt tension will cause damage to the alternator and water pump pulley bearings, while, on the other hand, loose belt tension will produce slip and premature wear on the belt. Therefore, be sure to adjust the belt tension to the proper level.
To adjust the tension on a drive belt, loosen the adjusting bolt or fixing bolt locknut on the alternator, alternator bracket or tension pulley. Then move the alternator or turn the adjusting bolt to adjust belt tension. Once the desired value is reached, secure the bolt or locknut and recheck tension.


REMOVAL & INSTALLATION

1.5L, 1.6L, 1.8L, 2.0L and 2.4L Engines


0900c15280037bf7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 1.5L, 1.6L, 1.8L, 2.0L and 2.4L engines
Alternator Belt


0900c15280037bf8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Loosen the adjuster lock bolt . . .


0900c15280037bf9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the alternator belt from the engine

  1. Loosen the alternator support nut.
  2. Loosen the adjuster lock bolt.
  3. Rotate the adjuster bolt counter clockwise to release the tension on the belt.
  4. Remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the adjuster bolt clockwise until the proper tension is reached.
  3. Tighten the adjuster lock bolt and the alternator support nut.

POWER STEERING BELT


0900c15280037bfa.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. After the adjusting and fixed bolts are loosened, rotate the pump . . .


0900c15280037bfb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the power steering belt from the engine

  1. Remove the alternator belt as described above.
  2. Loosen the power steering pump adjusting bolts.
  3. Remove the power steering pump fixed bolt on the rear of the bracket.
  4. Rotate the pump toward the engine and remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the pump until the proper tension is reached.
  3. Tighten the adjusting bolts on the pump.
  4. Tighten the fixed bolt on the rear of the bracket.
  5. Install the alternator belt.

A/C COMPRESSOR BELT
  1. Loosen the tension pulley and remove the belt.
  2. The installation is the reverse of the removal.

3.0L DOHC, 3.0L SOHC Galant, and 3.5L Engines


0900c15280037bfc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Serpentine belt routing-Mitsubishi 3.0L engines (except 1998-00 Galant models)


0900c15280037bfd.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 3.5L and 1998-00 3.0L SOHC Galant engines
ALTERNATOR AND A/C COMPRESSOR

  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the front undercover.
  2. Loosen the tension pulley fixing nut and relieve the tension on the belt by turning the adjusting bolt.
  3. Remove the belt.

To install:
  1. Install the belt on the crankshaft and alternator pulleys.
  2. Using the adjusting bolt on the tensioner, tighten the belt to the desired tension.
  3. Tighten the fixing nut to hold the adjustment.
  4. Install the undercover and lower the vehicle to the floor.
  5. Connect the negative battery cable.

POWER STEERING BELT
  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the undercover.
  2. Remove the alternator and A/C compressor belt.
  3. Lower the vehicle and remove the cruise control pump link assembly.
  4. Place the power steering hose under the oil reservoir.
  5. Loosen the tension pulley fixing bolts and remove the power steering pump drive belt.

To install:
  1. Install the power steering pump drive belt.
  2. Insert an extension bar or equivalent into the opening at the end of the tension pulley bracket and pivot the pulley to apply tension to the belt.
  3. Tighten the fixing bolts.
  4. Raise the vehicle and install the alternator and A/C compressor belt.
  5. Install the undercover and lower the vehicle.
  6. Connect the negative battery cable.

3.0L SOHC Diamante
  1. Disconnect the negative battery cable.
  2. Loosen the lockbolt on the face of the A/C tensioner pulley.
  3. Turn the adjusting bolt of the A/C tensioner pulley to loosen the tension of the A/C belt.
  4. Remove the A/C compressor belt.
  5. Loosen the locknut on the face of the power steering/alternator tensioner pulley.
  6. Turn the adjusting bolt of the tensioner pulley to loosen the tension of the belt.
  7. Remove the power steering/alternator belt.

To install:
  1. Install the power steering/alternator belt first and then the A/C compressor drive belt.
  2. Adjust the belts to the proper tension by turning the adjusting bolts and tighten pulley fixing nut/bolt.
  3. Tighten the mounting nut of the power steering/alternator tensioner pulley to 36 ft. lbs. (50 Nm).

Mar 21, 2013 | 1996 Mitsubishi Mirage

1 Answer

I want to know how to remove the alternator kia optima 2003


  1. Disconnect the negative battery cable.
  2. Temporarily loosen the water pump pulley bolts, 1.6L (VIN 3) engine only.
  3. Remove the front air intake inlet pipe bolts, 1.8L engine only.
  4. Remove the top hose from the air intake inlet pipe, 1.8L engine only.
  5. Remove the air intake inlet pipe clamp and the pipe, 1.8L engine only.
  6. Remove the power steering pump, 2.0L engine only.
  7. Remove the power steering pump bracket, 2.0L engine only.
  8. Remove the alternator B terminal cover cap.
  9. Disconnect the alternator electrical connections.
  10. Loosen, but do not remove the alternator pivot bolt and the tensioner mounting bolt.
  11. Remove the drive belt(s); relieve tension on the belt by rotating the adjustment bolt.
  12. Remove the water pump pulley, 1.6L (VIN 3) engine only.
  13. Remove the power steering pump, 1.6L (VIN 3) engine only.
  14. Remove the power steering pump bracket, 1.6L (VIN 3) engine only.
  15. Remove the alternator tensioner mounting bolt and the belt tensioner.
  16. Remove the alternator pivot bolt.
  17. Loosen the bolt at the base of the adjusting bracket and rotate the bracket up.
  18. Remove the alternator.

    0996b43f80207fa4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Alternator mounting-1.5L and 1.6L (VIN 5) engine shown


    0996b43f80207fa5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Alternator mounting-2.0L and 1.6L (VIN 3) engines shown


    0996b43f80231908.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Alternator mounting-2.4L and 2.7L engine


To install:
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Install the alternator.
  3. Install the alternator pivot bolt and hand-tighten at this time.
  4. Rotate the adjusting bracket into position, place the belt tensioner into position. Hand-tighten the mounting bolt.
  5. Install the drive belt.
  6. Adjust the belt tension by rotating the adjustment bolt.
  7. The belt deflection for 1.5L, 1.6L (VIN 5), 2.4L and 2.7L engines, is as follows:
    1. New belt: 0.22-0.28 in. (5.5-7mm).
    2. Used belt: 0.24-0.28 in. (6-7mm).

  8. The belt deflection for 1.6L (VIN 3) engine is as follows :
    1. New belt: 0.13-0.15 in. (3.3-3.7mm).
    2. Used belt: 0.17-0.19 in. (4.2-4.7mm).

  9. The belt deflection for the 2.0L engine, is as follows:
    1. New belt: 0.22-0.31 in. (5.5-8mm).
    2. Used belt: 0.33-0.45 in. (8.5-11.5mm).

  10. The belt deflection for the 1.8L engine, is as follows:
    1. New belt: 0.23-0.31 in. (6-8mm).
    2. Used belt: 0.28-0.35 in. (7-9mm).

  11. Tighten the tensioner bolt to 14-19 ft. lbs. (19-26 Nm) and the pivot bolt to 28-38 ft. lbs. (38-51 Nm).
  12. Connect the alternator electrical connections.
  13. Install the alternator B terminal cover cap.
  14. Install the power steering pump and adjust the power steering belt tension, 2.0L and 1.6L (VIN 3) engines only.
  15. Install the water pump pulley, 2006 1.6L engine only.
  16. Install the air intake inlet pipe and fasten the clamp, 1.8L engine only.
  17. Install the top hose to the air intake inlet pipe, 1.8L engine only.
  18. Install the front air intake inlet pipe bolts, 1.8L engine only.
  19. Connect the negative battery cable.

Feb 09, 2011 | 2003 Kia Optima

1 Answer

How do i replace the alternator?


REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. If equipped with a pulley cover shield, remove the shield at this time.
  3. Loosen the alternator pivot bolt. Remove the adjustment arm to alternator bolt. Pivot the alternator to gain slack in the drive belt and remove the belt.
  4. Disconnect and label (for correct installation) the alternator wiring. NOTE: Some models use a push-on wiring connector on the field and stator connections. Pull or push straight when removing or installing, or damage to the connectors may occur.
  5. Remove the pivot bolt and the alternator. Fig. 1: Alternator harness connections 86753014.gif
    Fig. 2: Remove and set aside the alternator belt 86753300.jpg
    Fig. 3: Remove the alternator pivot bolt 86753301.jpg
    Fig. 4: Tag and disconnect the wiring harness connector 86753302.jpg
    Fig. 5: Remove the alternator when it is completely detached 86753303.jpg
    To install:
  6. Position the alternator assembly onto the vehicle. Install the alternator pivot and adjuster arm bolts, but do not tighten them at this time.
  7. Install the alternator drive belt and adjust the drive belt tension.
  8. Once the proper belt tension is reached, tighten the adjuster bolt to 24–40 ft. lbs. (33–54 Nm) and the pivot bolt to 40–50 ft. lbs. (54–67 Nm).
  9. Reconnect the alternator wiring.
  10. Install the pulley shield, if equipped.
  11. Connect the negative battery cable.
prev.gif next.gif

Jul 11, 2010 | 1989 Ford Taurus

1 Answer

Changing alternator


REMOVAL & INSTALLATION
2.2L Engines
CHRYSLER ALTERNATOR
  1. Disconnect the negative battery cable.
  2. Label and disconnect the wiring (for easy installation).
  3. Remove the air conditioning compressor drive belt, if equipped.
  4. Loosen the alternator adjusting bracket bolt and adjusting bolt. Remove the alternator belt.
  5. Remove the bracket and mounting bolts.
  6. Remove the pivot bolt and nut.
  7. Lift the alternator from the vehicle.
When lifting the alternator out of the vehicle on some years with A/C, clearance may be restricted by the condenser cooling fan assembly or the A/C compressor and mounting bracket assembly, if so, removal of one of these items will be necessary.

To install:

  1. Position the alternator against the engine.
  2. Install the pivot bolt and nut.
  3. Install the mounting bracket bolts, and adjusting bolt.
  4. Install drive belts and adjust to specification.
  5. Tighten all the mounting bolts and nuts.
  6. Connect all alternator terminals.
  7. Connect the negative battery cable.

BOSCH ALTERNATOR

  1. Disconnect the negative battery cable.
  2. Disconnect the wiring and label for easy installation.
  3. Remove the air conditioning compressor drive belt.
  4. Loosen the alternator adjusting bracket locknut and adjusting screw. Remove the alternator belt.
  5. Remove the bracket locknut and mounting bolt.
  6. Remove the pivot bolt and nut.
  7. Remove the alternator from the engine.
To install:
  1. Position the alternator against the engine.
  2. Install pivot bolt and nut.
  3. Set the mounting bracket in place and install the bracket mounting bolt and locknut.
  4. Install the drive belts and adjust to specification.
  5. Tighten all the mounting bolts and nuts.
  6. Connect all alternator terminals.
  7. Connect the negative battery cable.

2.5L Engines
2.5L engines were equipped with either Chrysler or Bosch alternators.

  1. Disconnect the negative battery cable.
  2. Remove the drive belts.
  3. Remove the adjusting bracket-to-engine mounting bolt.
  4. Remove the adjusting locking bolt and nut, then remove the mounting bracket.
  5. Position the alternator to gain access to the wiring.
  6. Disconnect the wiring and label for easy installation.
  7. Remove the pivot bolt, nut, and washers.
  8. Remove the alternator assembly from the engine.
To install:
  1. Position the alternator assembly against the engine.
  2. Loosely install the pivot bolt, washers, and nut.
  3. Attach all wiring connectors to the alternator.
  4. Position the mounting bracket in place, then install engine mounting bolt.
  5. Loosely install the adjusting locking bolt and nut.
  6. Install the drive belts, and adjust to specification.
  7. Tighten all mounting bolts and nuts.
  8. Connect the negative battery cable.

2.6L Engines
2.6L engines were equipped with Mitsubishi alternators.
  1. Disconnect the negative battery cable.
  2. Disconnect the wiring and label for easy installation.
  3. Remove the adjusting strap mounting bolt.
  4. Remove the drive belts.
  5. Remove the support mounting bolt and nut.
  6. Remove the alternator assembly.
To install:
  1. Position the alternator assembly against the engine, then install the support bolt.
  2. Install the adjusting strap mounting bolt.
  3. Install the alternator belts and adjust to specification.
  4. Tighten all the support bolts and nuts.
  5. Connect all of the wiring terminals to the alternator.
  6. Connect the negative battery cable.

3.0L Engines
The 3.0L engines were equipped with either the Nippondenso or Bosch alternators.
  1. Disconnect the negative battery cable.
  2. Install a 1 / 2 in. breaker bar in the tensioner slot. Rotate counterclockwise to release belt tension and remove poly-V belt.
  3. Remove the alternator mounting bolts (2).
  4. Remove the wiring and remove alternator.
To install:
  1. Position the alternator onto the engine, then install the wiring.
  2. Set the alternator against the mounting bracket and install the mounting bolts.
  3. Rotate the tensioner counterclockwise and install poly-V belt.
  4. Connect the negative battery cable.

3.3L and 3.8L Engines
The 3.3L and 3.8L engines were equipped with the Nippondenso alternators.
  1. Disconnect the negative battery cable.
  2. Remove the alternator drive belt, by relieving the tension on the dynamic tensioner.
  3. Loosen the nut on the support bracket at the exhaust manifold, do not remove it.
  4. Remove the alternator tensioner/power steering bracket bolt.
  5. Remove the tensioner stud nut and remove the tensioner.
  6. Remove the alternator mounting bolts.
  7. Remove the power steering reservoir from the mounting bracket, do not disconnect the hoses, and position it out of the way.
  8. Remove the alternator support bracket bolts. Remove the intake plenum to alternator bracket bolt and remove the alternator support bracket from the engine.
  9. Remove the alternator from the engine and disconnect the electrical leads.
To install:
  1. Install the alternator in position on the engine and connect the electrical leads.
  2. Install the alternator support bracket, tighten the retaining bolts to 40 ft. lbs. (54 Nm).
  3. Install the power steering reservoir on the mounting bracket.
  4. Install the alternator mounting bolts, tighten the bolts to 40 ft. lbs. (54 Nm).
  5. Install the tensioner and tensioner mounting stud. Install the retaining nut on the exhaust manifold.
  6. Install the alternator belt, insert a 1 / 2 in. extension into the square hole in the tensioner and turn the tensioner. Tighten the tensioner bolt.
  7. Connect the negative battery cable.

Hope this help (remember comment and rated this).

Apr 01, 2010 | 1994 Dodge Caravan

1 Answer

How to install 03 ford focus alternator?


Removing the Alternator
Disconnect battery ground cable
Remove the ground wire (black) from the alternator
Disconnect the positive wire (red wire held on by a retaining nut) from the back of the alternator
Now disconnect the wire harness from the alternator
Remove the drive belt
NOTE: Some models use a belt tensioner that applies tension to the drive belt.
The best tool to use for this job is the serpentine belt too.
If you can borrow one from a neighbour you can get one at PartSource. (Part# 648451)
On other models you will have to loosen the adjusting bolt on the alternator bracket.
If you're not sure about how to remove the drive belt, visit your local PartSource for free print outs of vehicle specific instructions.
Take off the mounting bolts from the alternator bracket
Now remove the alternator from the engine compartment There. You've removed the alternator. How easy was that?
Installing Your New Alternator
Put the alternator in the engine compartment
Install the mounting bolts that connect the alternator to the alternator bracket
Connect the alternator wiring harness
Now connect the positive wire to the alternator
NOTE: Your new alternator should come with a retaining nut.
Remember to remove the nut before you install the positive wire.
If it doesn't keep the old nut.
Connect the ground wire to the alternator
Now install the drive belt
This is a great time to replace your old worn out belt. When inspecting your old belt look for signs of cracking, oil soaked, hard glazed, splitting or fraying.
All these signs mean it's time you replaced your drive belt.
If your vehicle no longer has the belt routing diagram under the hood, visit your local PartSource for a free print out of the belt routing diagram.
Reconnect the ground battery cable .

Nov 19, 2009 | 2003 Ford Focus

1 Answer

Remove and replace alternator


2000 Ford Truck Expedition 4WD 4.6L EFI 8cyl

Alternator - REMOVAL & INSTALLATION

4.2L Engine

  1. Disconnect the negative battery cable.
  2. Disconnect 2 alternator and voltage regulator electrical harness connectors at the alternator. To disconnect push-on type terminals, depress the lock tab and pull straight off.
  3. Remove the positive battery cable nut and remove the positive battery cable at the alternator.
  4. Rotate the drive belt tensioner away from the drive belt and remove the drive belt from the alternator pulley.
  5. Remove 3 alternator retaining bolts and remove the alternator.
To install:
  1. Place the alternator on the engine and install 3 alternator retaining bolts. Tighten the bolts to 18-22 ft. lbs. (20-30 Nm).
  2. Rotate the drive belt tensioner away from the drive belt and install the drive belt on the alternator pulley.
  3. Connect 2 alternator and voltage regulator electrical harness connectors.
  4. Connect the positive battery cable to the alternator and install the nut and washer. Tighten the nut to 84 inch lbs. (10 Nm).
  5. Connect the negative battery cable.
  6. Start the engine and check for proper charging system operation.
4.6L, 5.4L and 6.8L Engines

f52fc60.jpg

Fig. 1 Detach the connectors from the alternator

ffe1937.jpg

Fig. 2 Remove the nut and the battery cable from the post on the rear of the alternator

6ce39ae.jpg

Fig. 3 Remove the 2 front alternator mounting bolts and ...

45a032e.jpg

Fig. 4 Remove the alternator from the engine by carefully lifting it up and...

6513790.jpg

Fig. 5 ... out of the engine compartment
  1. Disconnect the negative battery cable.
  2. Rotate the drive belt tensioner away from the drive belt and remove the drive belt from the alternator pulley.
  3. Detach the electrical harness connectors at the alternator assembly.
  4. Disconnect the positive battery cable and remove the nut and washer.
  5. Remove 2 front alternator bolts.
  6. Remove the rear alternator support bracket retaining bolts and the support bracket.
  7. Remove the alternator from the vehicle.
To install:
  1. Place the alternator in position and loosely install 2 front alternator retaining bolts.
  2. Install the alternator bracket and 3 alternator bracket bolts. Tighten to 84 inch lbs. (10 Nm).
  3. Tighten 2 front alternator retaining bolts to 19 ft. lbs. (26 Nm).
  4. Connect 2 electrical harness connectors to the alternator assembly.
  5. Connect the positive battery cable and install the nut and washer. Tighten the nut to 72 inch lbs. (8 Nm).
  6. Rotate the drive belt tensioner away from the drive belt and install the drive belt on the alternator pulley.
  7. Connect the negative battery cable.
  8. Start the engine and check for proper charging system operation.
5.8L and 7.5L Gasoline Engines and 7.3L Diesel Engine
  1. Disconnect the battery ground cable.
  2. Label and detach the connectors from the alternator.
  3. Release the tensioner and remove the drive belt from the alternator pulley.
  4. Remove the alternator retaining bolts.
  5. Remove the alternator from the vehicle.
To install:
  1. Position the alternator and install the retaining bolts. Tighten the retaining bolts to 15-21 ft. lbs. (21-29 Nm).
  2. Install the drive belt.
  3. Attach the alternator connectors.
  4. Connect the battery ground cable.

I really hope help you with this (remember rated this help) Good luck.

Oct 13, 2009 | 2000 Ford Expedition

1 Answer

How to check alternator, and how to replace it.



Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Temporarily loosen the water pump pulley bolts, 1.6L (VIN 3) engine only.
  4. Remove the front air intake inlet pipe bolts, 1.8L engine only.
  5. Remove the top hose from the air intake inlet pipe, 1.8L engine only.
  6. Remove the air intake inlet pipe clamp and the pipe, 1.8L engine only.
  7. Remove the power steering pump, 2.0L engine only.
  8. Remove the power steering pump bracket, 2.0L engine only.
  9. Remove the alternator B terminal cover cap.
  10. Disconnect the alternator electrical connections.
  11. Loosen, but do not remove the alternator pivot bolt and the tensioner mounting bolt.
  12. Remove the drive belt(s); relieve tension on the belt by rotating the adjustment bolt.
  13. Remove the water pump pulley, 1.6L (VIN 3) engine only.
  14. Remove the power steering pump, 1.6L (VIN 3) engine only.
  15. Remove the power steering pump bracket, 1.6L (VIN 3) engine only.
  16. Remove the alternator tensioner mounting bolt and the belt tensioner.
  17. Remove the alternator pivot bolt.
  18. Loosen the bolt at the base of the adjusting bracket and rotate the bracket up.
  19. Remove the alternator.

    0900c15280028419.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Alternator mounting-1.5L and 1.6L (VIN 5) engine shown


    0900c1528002841a.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Alternator mounting-2.0L and 1.6L (VIN 3) engines shown


    0900c1528002841b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Alternator mounting-2.4L and 2.7L engine

To install:
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Install the alternator.
  3. Install the alternator pivot bolt and hand-tighten at this time.
  4. Rotate the adjusting bracket into position, place the belt tensioner into position. Hand-tighten the mounting bolt.
  5. Install the drive belt.
  6. Adjust the belt tension by rotating the adjustment bolt.
  7. The belt deflection for 1.5L, 1.6L (VIN 5), 2.4L and 2.7L engines, is as follows:
    1. New belt: 0.22-0.28 in. (5.5-7mm).
    2. Used belt: 0.24-0.28 in. (6-7mm).

  8. The belt deflection for 1.6L (VIN 3) engine is as follows :
    1. New belt: 0.13-0.15 in. (3.3-3.7mm).
    2. Used belt: 0.17-0.19 in. (4.2-4.7mm).

  9. The belt deflection for the 2.0L engine, is as follows:
    1. New belt: 0.22-0.31 in. (5.5-8mm).
    2. Used belt: 0.33-0.45 in. (8.5-11.5mm).

  10. The belt deflection for the 1.8L engine, is as follows:
    1. New belt: 0.23-0.31 in. (6-8mm).
    2. Used belt: 0.28-0.35 in. (7-9mm).

  11. Tighten the tensioner bolt to 14-19 ft. lbs. (19-26 Nm) and the pivot bolt to 28-38 ft. lbs. (38-51 Nm).
  12. Connect the alternator electrical connections.
  13. Install the alternator B terminal cover cap.
  14. Install the power steering pump and adjust the power steering belt tension, 2.0L and 1.6L (VIN 3) engines only.
  15. Install the water pump pulley, 2006 1.6L engine only.
  16. Install the air intake inlet pipe and fasten the clamp, 1.8L engine only.
  17. Install the top hose to the air intake inlet pipe, 1.8L engine only.
  18. Install the front air intake inlet pipe bolts, 1.8L engine only.
  19. Connect the negative battery cable.

Jul 29, 2009 | 2002 Kia Spectra

2 Answers

Bad alternator


Disconnect the negative clamp on the battery. Remove the bolt on the adjustment arm (the one with the slot) of the alternator. Loosen the pivot bolt at the bottom of the Alt. Swing the alt inward to loosen the belt. Take the belt of the pulley. Take off the wires noting where they attach. Remove the pivot bolt. You should be able to take the alt off now. Reverse the sequence but when adjusting the belt tension pry the side of the alternator with a bar so the belt can only be deflected about three quarters of an inch. Tighten the adjustment bolt. Don't over tighten the belt. It'll prematurely wear your bearings. Don't under tighten. It'll squeal.

May 08, 2009 | Ford Explorer Cars & Trucks

1 Answer

Changing the starter on a Kia Spectra


Here's step-by-step instructions on how to access, remove and re-install your alternator. Hope it helps! Have a great day!

Alternator Kia_Sephia_Rio_Spectra_Optima_1998-2006
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Temporarily loosen the water pump pulley bolts, 1.6L (VIN 3) engine only.
  4. Remove the front air intake inlet pipe bolts, 1.8L engine only.
  5. Remove the top hose from the air intake inlet pipe, 1.8L engine only.
  6. Remove the air intake inlet pipe clamp and the pipe, 1.8L engine only.
  7. Remove the power steering pump, 2.0L engine only.
  8. Remove the power steering pump bracket, 2.0L engine only.
  9. Remove the alternator B terminal cover cap.
  10. Disconnect the alternator electrical connections.
  11. Loosen, but do not remove the alternator pivot bolt and the tensioner mounting bolt.
  12. Remove the drive belt(s); relieve tension on the belt by rotating the adjustment bolt.
  13. Remove the water pump pulley, 1.6L (VIN 3) engine only.
  14. Remove the power steering pump, 1.6L (VIN 3) engine only.
  15. Remove the power steering pump bracket, 1.6L (VIN 3) engine only.
  16. Remove the alternator tensioner mounting bolt and the belt tensioner.
  17. Remove the alternator pivot bolt.
  18. Loosen the bolt at the base of the adjusting bracket and rotate the bracket up.
  19. Remove the alternator. 0900c15280028419.jpgAlternator mounting—1.5L and 1.6L (VIN 5) engine shown 0900c1528002841a.jpgAlternator mounting—2.0L and 1.6L (VIN 3) engines shown 0900c1528002841b.jpgAlternator mounting—2.4L and 2.7L engine
To install:
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Install the alternator.
  3. Install the alternator pivot bolt and hand-tighten at this time.
  4. Rotate the adjusting bracket into position, place the belt tensioner into position. Hand-tighten the mounting bolt.
  5. Install the drive belt.
  6. Adjust the belt tension by rotating the adjustment bolt.
  7. The belt deflection for 1.5L, 1.6L (VIN 5), 2.4L and 2.7L engines, is as follows:
    1. New belt: 0.22-0.28 in. (5.5-7mm).
    2. Used belt: 0.24-0.28 in. (6-7mm).
  8. The belt deflection for 1.6L (VIN 3) engine is as follows :
    1. New belt: 0.13-0.15 in. (3.3-3.7mm).
    2. Used belt: 0.17-0.19 in. (4.2-4.7mm).
  9. The belt deflection for the 2.0L engine, is as follows:
    1. New belt: 0.22-0.31 in. (5.5-8mm).
    2. Used belt: 0.33-0.45 in. (8.5-11.5mm).
  10. The belt deflection for the 1.8L engine, is as follows:
    1. New belt: 0.23-0.31 in. (6-8mm).
    2. Used belt: 0.28-0.35 in. (7-9mm).
  11. Tighten the tensioner bolt to 14-19 ft. lbs. (19-26 Nm) and the pivot bolt to 28-38 ft. lbs. (38-51 Nm).
  12. Connect the alternator electrical connections.
  13. Install the alternator B terminal cover cap.
  14. Install the power steering pump and adjust the power steering belt tension, 2.0L and 1.6L (VIN 3) engines only.
  15. Install the water pump pulley, 2006 1.6L engine only.
  16. Install the air intake inlet pipe and fasten the clamp, 1.8L engine only.
  17. Install the top hose to the air intake inlet pipe, 1.8L engine only.
  18. Install the front air intake inlet pipe bolts, 1.8L engine only.
  19. Connect the negative battery cable.
 

Nov 23, 2008 | 2003 Kia Spectra

Not finding what you are looking for?
2000 Mazda 626 Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...