Question about 2007 Mercedes-Benz ML350

1 Answer

How do reset the brake pads sensor? - 2007 Mercedes-Benz ML350

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 462 Answers

After you replace brakes and sensor it should go off on it's own.
check the rest of the sensors , maybe you need the other end brake job.

Posted on Apr 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW DO I RESET MY BRAKE PAD LIGHT ON 2005 MERCEDES BENZ SL500


Hi,

Typically you cannot "reset" the light. The light illuminates when it becomes grounded, via a small wire pushed into the brake pad itself. The only repair is to replace the brake pads, (turn/replace the rotors) and replace however many sensors are damaged.

Save money next time and inspect/replace before you ruin the sensors...

Doc

Oct 02, 2014 | Cars & Trucks

1 Answer

How to reset service indicator light on 2005 Mini cooper S


low fluid level will keep the light on also the pad wear sensors need to be replace once the pads have worn down to the sensor they are not resetting sensors

Aug 14, 2012 | Cars & Trucks

2 Answers

Replace brake pad light on, how do you reset it?


you need to replace the pad wear sensor when the pad wears down it wears the sensor and the sensor needs to be replace if you look at the sensor you can see the wire on the sensor wears threw

May 19, 2012 | 2009 Audi Q7

1 Answer

Brake pad wear indicator light does not go off at the dash after changing rotors brake pads and the sensor in the front wheels all pads and rotors and the sensor is ok at rear. the vehicle has only 30000...


Did you change the sensor? if you did, do a battery reset (disconnect for 10 to 20 min.).

Obviously the wear sensor has made contact with the rotor and is already damaged. You're not even suppose to resuse the wear pad sensor if its worn or damaged anyways.The way how the sensor works is that it must make contact to the rotor to complete the wear pad light indicator circuit. There is no mentioning that he replaced the the wear pad sensor with a new one.

But if one did replaced the wear pad sensor and the wear pad indicator is lit up, the way to reset it is to leave the key on in ignition switch #2 or #1 for about 30sec. turn it off and its reset.

Its possible that you forgot to replace the brake light sensors. They are about 15 bucks, and have to be replaced in order for that light to turn off. You can either get them from the dealer where they'll likely charge you 3 times as much, or you can go to http://www.turnermotorsport.com and get them there.

You have to reset the light by leaving the ignition switch on position #2 for about 30 sec. turn off the ignition and start the engine up and see if it goes out. I recommend buying a new wear pad sensor as well because now light will lit up when you're way below spec (less than 3mm)

Also, you could try with this procedure for one E39: Turning off the Check Brake Linings warning on the Instrument Cluster...
- so you've just changed the brake pads on your E39, along with the wear sensors. The old sensor(s) needed replacement cause you waited a bit too long before changing the pads, and wore through the sensor(s), turning on the BRAKE light on the dash. But wait, the light is still on? But there's a new sensor installed... what gives?!
- there is a procedure required in order to turn off the light/warning. With the ignition off, step on and hold the brake pedal. Now, while holding the brake pedal down, turn on the ignition switch to position 2 (just before cranking). Hold the brake pedal until the BRAKE light is off. Tada, the warning is gone and reset.

NOTE: This procedure worked on a 2001 E46 325i. It took about 15-20 seconds, but it cleared out w/o having to unhook the battery.

Other details find in the Owners Manual 2006-BMW-Z4m-Roadster-Owner-Manual

Keep us updated.

Nov 04, 2010 | 2006 BMW Z4 Roadster

3 Answers

How to reset brake light after changing pads.


Hi Peters6709,
Sorry to tell you, but you need to replace the pad-wear sensors as well. They are the little trapezoid pieces that hang inside the tops of the inside pads. They should run about $10 each. Once replaced, disconnect the battery completely for about 10 minutes, if you have a stock radio keep the code handy.

Next time check the pads every 10-12K miles. I have been running the SAME pad wear sensors on my Z3 for the past 2 pad changes now after making the same mistake the first time.

Best of luck!

May 02, 2010 | 1999 BMW 323 Series

3 Answers

How to shut off Brake wear sensor after pad change


If the brake pads were worn enough to activate the warning light the sensor or sensors must be replaced. There is no reset for this.

Oct 24, 2009 | 2004 Lexus LS 430

2 Answers

How do I reset brake pad warning indicator light after servicing brakes.


disconnect + battery terminal and start car then pump brakes till light goes out then test

Aug 22, 2009 | 1999 Mercury Cougar

1 Answer

Replace brake pad light on, how do you reset it?


Did you change the sensors when you changed the pads?

Mar 21, 2009 | 2001 Audi A6

2 Answers

I replaced the front pads on a VW JETTA 2.5 and the check pads light is on. How can I reset the check pads light?


As the brake pads wear, the brake pad wear sensor contained in the brake pad contacts the brake rotor. This causes the sensor to fail. When a pad wear sensor fails it opens the ground circuit of the pad wear warning light system causing the pad wear warning light to illuminate. Perform normal brake service to correct this condition and be sure to replace the brake pads with pads containing wear sensors. Once the brake pads and wear sensors are replaced, reset the brake pad warning system by turning the ignition switch to the "on" position. As long as continuity to ground exists through all the brake pad wear sensors the system should reset and the pad warning light in the dash will go out. If the pad warning light does not go out, a check of the pad warning circuit for an open circuit condition or poor ground must be performed.

Mar 03, 2009 | 2005 Volkswagen Jetta

3 Answers

BRAKE WARNING LIGHT


I dunno if this will work on your BMW, but on my BMW Z3 and M3, it was....

Turn the ignition key to position 2, but do NOT start the car. Wait for about 45 seconds and the brake warning message will be reset.

If it doesn't reset, then the brake sensor was damage. You will need to replace the brake sensor. It sounds like you replace the brake right after you saw the warning, so the brake sensor should be okay.

Dec 19, 2008 | 2003 BMW 325

Not finding what you are looking for?
2007 Mercedes-Benz ML350 Logo

Related Topics:

523 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...