Question about 1991 GMC K2500

1 Answer

When put into 4 high from 2wd I hear a squeek squeek squeek while driving about 20 or 30 km per hour

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 972 Answers

You have a bad ujoint on your front drive shaft. remove shaft and replace the bad one but i would replace both. its squeeking cause the bearings in it have turned to rusty powder and are dry, the bad one will be easy to spot

Posted on Apr 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 ford ranger - Where is the 4x4 actuator located


On the transfer case
Transfer Case - Electronic Shift
The four-wheel drive electronic shift-on-the-fly feature electrically shifts the vehicle transfer case between 2WD, 4WD HIGH, and 4WD LOW. The system mode is selected by the operator through the mode select switch (MSS) on the instrument panel. The operator is informed which mode the system is in by two instrument cluster indicators: one for 4WD HIGH which appears as 4WD, and one for 4WD LOW, which appears as 4WD LOW. Shifts into 4WD HIGH can be made at any speed. When shifting into 4WD HIGH with the vehicle stationary, tooth blockage may occur preventing shift completion. When the vehicle is driven above 8 km/h (5 mph) the shift will complete. When shifting in or out of 4WD LOW, the four-wheel drive (4WD) control module requires that the vehicle speed be less than 5 km/h (3 mph), the brake pedal be applied, and the transmission be in NEUTRAL (automatic transmission) or the clutch pedal be depressed (manual transmission).
The gearmotor encoder assembly is mounted externally on the transfer case. It drives a rotary cam which moves the mode fork and range fork within the transfer case between the 4WD HIGH, 4WD LOW, and 2WD range positions.
The four-wheel drive (4WD) control module controls the gearmotor encoder assembly that shifts between 4WD HIGH, 4WD LOW, and 2WD modes.

Mar 17, 2017 | Ford Cars & Trucks

1 Answer

If 360 km per hour is equal to 40 miles per hour, please show me how to calculate using formular


360 km/hr is NOT 40 miles/hr.
1 mile is about 1.6 km
To go from km to miles, multiply by 0.62
To go from miles to km, multiply by 1.6

Kilometers per hour to Miles per hour

Feb 23, 2017 | Cars & Trucks

2 Answers

Does the driving on overdrive mode cause high fuel consumption, because the transmission use the first three ratios mostly?


Driving in overdrive, say on a trip where your speeds are over 65 to 70..Actually saves gas, but using overdrive to drive around town not only uses more gas, but can cause damage to your transmission.

Dec 23, 2014 | 2000 Audi A6

1 Answer

2008 Silverado Z71 grinding noise in 4 wheel high - what is the cause


Could be the axle trying to engage or it could be in the transfer case. Suggest you put it on stands all around and have some one listen underneath for exact location while engaging it.

Sep 12, 2014 | Cars & Trucks

1 Answer

High temprature


Mid way is ok, but u need check thermostat, cheap to replace, also check rad is not blocked with insects, oil ok? Water cap tight? Turn on heat full in car see the temp drop, water pump can be on way out

Apr 05, 2013 | 2006 Nissan Armada

1 Answer

1985 ford not staying in 2 wheel drive


your 4 wheel shifter is hitting the floor now ..i made a notch in the floor so the shifter can go foward all the way..check your fan shroud to..fan is really close now

Mar 10, 2013 | 1985 Ford F150

1 Answer

Will not go in 4 low 4x4 lights start blinking after trying . reset light by unhooking battery . then goes in 4 high normelly but not 4 low. i thlnk auto 4 is working 4 liter SOHC 1998


Normally 4 wheel drive HIGH is engaged on the fly or as you are moving more than 10 km per hour or 10 miles per hour but 4 wheel drive LOW is engaged at around 3 to 5 mph. no more or you could ruin the transfer case. Try going from 2 high to 4 high by switching back and forth and then try 2 high to 4 low when idling along. What usually happens is the mechanics under the car freeze up or rust up and you have to switch back and forth to free it up.

Nov 01, 2010 | 1998 Ford Explorer

1 Answer

It stalls after 15 min driving 110 km per hour if i go 80 or 90 its good fuel filter pump are new thx


sounds like the fuel pump is not putting enough fuel through to keep up with the demand of 110 km ph
but is putting out enough for the 80-90- km ph
advise the install of a larger low (litres per minute) fuel pump

Sep 20, 2010 | 1987 Buick LeSabre

1 Answer

My jeep will not shift into 4low but 2wd and part time and 4high works fine then when you try to put it into 4 low its hard to pull up then when its their and you let offf the brake it just makes a loud...


Well, in the future it would be better to let us know what it is exactly that you drive, (cherokee, grand, jk, cj, ....)however, i'm guessing from the picture that you drive a grand. I dont know how long you have owned it or if you have put it in 4 low before, but you need to put the normal transmission in neutral before shifting to 4 low using the transfer case (the thing that gives you 4wheel drive via the lever) However, on your vehicle, if you have full time 4 wheel, i think you have the selec-trac transfer case and only have a switch. According to the Jeep website and i'm assuming your manual, you need to slow the vehicle to 2-3 miles per hour and then place it in neutral before attempting to shift to 4 low.

Jeep Site
http://www.jeep.com/en/4x4/how_systems_work/selec_trac_2/

Joel

Feb 18, 2009 | 1995 Jeep Grand Cherokee

1 Answer

98 Ford Ranger Squeeks when accelerating


do you hear the squeeking in the truck only if so then its the little o ring plastic in the peddle makeing the noise.

Feb 04, 2009 | 2003 Ford Ranger Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...